Bedienungsanleitung Sony mz-r410 (Seite 16 von 64) (Englisch)

157183

Zoom out

Zoom in

Vorherige Seite

1/64

Nächste Seite

Notes

• The pause function cannot be turned on or off

manually during synchro-recording. Press x

to stop recording.

• Do not change “SYNC-R” setting while

recording. Recording may not be done

properly.

• Even when there is no recorded sound on the

sound source, there may be cases when

recording does not pause automatically during

synchro-recording due to the noise level

emitted from the sound source.

• If a silent portion is encountered for

approximately 2 seconds during synchro-

recording from a sound source other than a

CD or an MD, a new track mark is

automatically added at the point where the

silent portion ends.

• Synchro-recording cannot be done if the

connecting cord is not an optical cable.

• You cannot change the recording mode during

recording.

• “Saving” or “Edit” flashes while data of the

recording (the track’s start and end points,

etc.) is being recorded. Do not move the

recorder or disconnect the power source while

the indication is flashing in the display.

• The lid does not open until “Edit” disappears

in the display.

• If the power supply is disrupted (i.e. the

battery is removed or becomes exhausted or

the AC power adaptor is disconnected) during

a recording or editing operation, or while

“Edit” appears in the display, then it will not

be possible to open the lid until power is

restored.

• You can make a digital recording only from an

optical type output.

• When recording from a portable CD player,

set the CD player to pause, and then do the

recording procedure on the recorder.

• Note the following when recording from a

portable CD player:

—Some portable CD players may not be

capable of digital out when the AC power

adaptor is disconnected. If this is the case,

connect the AC power adaptor to the

portable CD player and use it on AC power

as the power source.

—On some portable CD players, optical

output may not be possible when using an

anti-skip function (e.g., ESP* or G-

PROTECTION). If this is the case, turn off

the anti-skip function.

∗ Electronic Shock Protection

• When there is no sound (page 60) from the

player for more than 3 seconds during

synchro-recording, the recorder goes into the

standby mode automatically. When the sound

comes from the player again, the recorder

resumes synchro-recording. If the recorder is

kept in the standby mode for 5 minutes or

longer, the recorder stops automatically.

• For MDLP recording, follow steps 1 to 3 of

“Long-time recording (MDLP)” (page 21) to

select the recording mode, and then start the

procedure of synchro-recording.

• LINE IN (OPTICAL) jack is for both digital

and analog input. The recorder automatically

recognizes the type of line cable and switches

to digital or analog input.

• The recording level is adjusted automatically.

To adjust the level manually, see “Adjusting

the recording level manually (Manual

Recording)” (page 26).

• You can monitor the sound during recording.

Connect the headphones/earphones to i and

adjust the volume by pressing VOL +, –. This

does not affect the recording level.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Sony mz-r410 Seite 16

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Sony mz-r410

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info