Bedienungsanleitung Sony MZM100 (Seite 74 von 119) (Englisch)

23382

Zoom out

Zoom in

Vorherige Seite

1/119

Nächste Seite

Playback sound skips. • The recorder is placed where it receives continuous vibration.

, Put the recorder on a stable place.

• A very short track may cause sound to skip.

, Try not to create a short track.

Momentary noise is

heard.

• Due to the special digital audio compression technology used in

LP4 mode, momentary noise may occur on very rare occasions

with certain sound sources.

Sound has a lot of static. • Strong magnetism from a television or such device is interfering

with operation.

, Move the recorder away from the source of strong magnetism.

The volume of the

recorded track is low.

• The track was recorded in analog mode (in digital mode, the

recording level is automatically set to the same level as that of the

sound source). Or you used a connecting cord with an attenuator.

, Use a correct connecting cord without an attenuator.

• The recording level was low.

, Adjust the recording level manually while recording (page 35).

Volume cannot be turned

up.

•AVLS is on.

, Release the AVLS settings (page 57).

No sound comes through

the earphones.

• The earphones plug is not firmly connected.

, Plug in the plug of the earphones firmly to the remote control.

Plug in the plug of the remote control firmly to the i jack.

• The plug is dirty.

, Clean the plug.

The disc cannot be

played on another

component.

• The component does not support Hi-MD.

, Discs recorded on this recorder can be played only on

components that support Hi-MD.

The edited tracks may

exhibit sound dropout

during search operations.

• This occurs due to the MiniDisc system limitation. The

fragmentation of data may cause sound dropout while searching

because the tracks are played in higher speed than normal

playback.

There is no R-channel

sound output when

playing a track recorded

from a cassette deck or

through an amplifier, or

when listening to sound

from a cassette deck or

amplifier.

• There is no R-channel output if the cassette deck or an amplifier is

connected with a monaural cord.

, Make sure to use a stereo connecting cord. If, however, the

connected equipment is monaural, there will be no R-channel

sound output even with a stereo connecting cord.

The recorder cannot play

MP3 tracks.

• You tried to play an MP3 track with a format not supported by this

recorder.

, This recorder only supports MP3 tracks (MPEG-1 Audio

Layer-3/Sampling frequency 44.1 kHz) that have been

transferred using the SonicStage software.

“R” appears in the

display window during

playback.

• “R” appears when the contents of an editing operation performed

during recorder playback are ready to be written to the disc.

, When playback on the recorder is stopped, the edited contents

are written to the disc and the “R” disappears.

Symptom Cause/Remedy

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Sony MZM100 Seite 74

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info