21353
12
Zoom out
Zoom in
Vorherige Seite
1/120
Nächste Seite
2-050-330-11(3)
© 2004 Sony Corporation
DVD Recorder
Operating Instructions
RDR-HX900/HX1000
2
WARNING
To prevent fire or shock hazard, do not
expose the unit to rain or moisture.
To avoid electrical shock, do not open
the cabinet. Refer servicing to qualified
personnel only.
The mains lead must only be changed
at a qualified service shop.
This appliance is classified as a
CLASS 1 LASER product. The
CLASS 1 LASER PRODUCT
MARKING is located on the rear
exterior.
CAUTION
The use of optical instruments with this
product will increase eye hazard. As
the laser beam used in this DVD
recorder is harmful to eyes, do not
attempt to disassemble the cabinet.
Refer servicing to qualified personnel
only.
This label is located on the laser
protective housing inside the
enclosure.
Notice for customers in the
United Kingdom and Republic of
Ireland
A moulded plug complying with
BS1363 is fitted to this equipment for
your safety and convenience.
Should the fuse in the plug supplied
need to be replaced, a 5 AMP fuse
approved by ASTA or BSI to BS1362,
(i.e., marked with or mark)
must be used.
If the plug supplied with this
equipment has a detachable fuse cover,
be sure to attach the fuse cover after
you change the fuse. Never use the
plug without the fuse cover. If you
should lose the fuse cover, please
contact your nearest Sony service
station.
Precautions
This unit operates on 220 – 240 V
AC, 50/60 Hz. Check that the unit’s
operating voltage is identical with
your local power supply.
To prevent fire or shock hazard, do
not place objects filled with liquids,
such as vases, on the apparatus.
VIDEO Plus+ and PlusCode are
registered trademarks of Gemstar
Development Corporation. The
VIDEO Plus+ system is manufactured
under license from Gemstar
Development Corporation.
Precautions
This equipment has been tested and
found to comply with the limits set
out in the EMC Directive using a
connection cable shorter than 3
metres.
On safety
Should any solid object or liquid fall
into the cabinet, unplug the recorder
and have it checked by qualified
personnel before operating it any
further.
On power sources
The recorder is not disconnected
from the AC power source (mains)
as long as it is connected to the
wall outlet, even if the recorder
itself has been turned off.
If you are not going to use the
recorder for a long time, be sure to
disconnect the recorder from the
wall outlet. To disconnect the AC
power cord (mains lead), grasp the
plug itself; never pull the cord.
Before disconnecting the AC
power cord (mains lead), check
that the recorder’s hard disk is not
operating (recording or dubbing)
on the front panel display.
On placement
Place the recorder in a location
with adequate ventilation to
prevent heat build-up in the
recorder.
Do not place the recorder on a soft
surface such as a rug that might
block the ventilation holes.
Do not place the recorder in a
confined space such as a bookshelf
or similar unit.
Do not place the recorder in a
location near heat sources, or in a
place subject to direct sunlight,
excessive dust, or mechanical
shock.
Do not place the recorder in an
inclined position. It is designed to
be operated in a horizontal
position only.
Keep the recorder and discs away
from equipment with strong
magnets, such as microwave
ovens, or large loudspeakers.
CAUTION
CLASS 3B VISIBLE AND INVISIBLE LASER RADIATION WHEN OPEN.
AVOID DIRECT EXPOSURE TO THE BEAM.
RADIATIONS LASER VISIBLES ET INVISIBLES DE CLASSE 3B EN CAS
D’OUVERTURE. EVITER TOUTE EXPOSITION DIRECTE AU FAISCEAU.
KLASSE 3B SICHTBARE UND UNSICHTBARE LASERSTRAHLUNG WENN
GEÖFFNET. DIREKTEN KONTAKT MIT DEM STRAHL VERMEIDEN.
UNDGÅ DIREKTE UDSÆTTELSE FOR STRÅLING.
SYNLIG OG USYNLIG LASERSTRÅLING AF KLASSE 3B VED ÅBNING.
UNNGÅ DIREKTE EKSPONERING FOR STRÅLEN.
SYNLIG OG USYNLIG LASERSTRÅLING I KLASSE 3B NÅR DEKSEL ÅPNES.
KLASS 3B SYNLIG OCH OSYNLIG LASERSTRÅLNING NÄR DENNA DEL ÄR
ÖPPNAD. UNDVIK ATT DIREKT EXPONERA DIG FÖR STRÅLNINGEN.
AVATTUNA LUOKAN 3B NÄKYVÄÄ JA NÄKYMÄTÖNTÄ LASERSÄTEILYÄ.
VÄLTÄ SUORAA ALTISTUMISTA SÄTEELLE.
ATTENTION
VORSICHT
ADVARSEL
ADVARSEL
VARNING
VAR O!
3
Do not place heavy objects on the
recorder.
On recording
Note that the contents of the
recording cannot be compensated
for under any and all conditions,
including conditions that may
arise due to a malfunction of this
unit.
Make trial recordings before
making the actual recording.
About the hard disk drive
The hard disk has a high storage
density, which enables long
recording durations and quick
access to the written data. However,
it can easily be damaged by shock,
vibration or dust, and should be kept
away from magnets. To avoid losing
important data, observe the
following precautions.
Do not apply a strong shock to the
recorder.
Do not place the recorder in a
location subject to mechanical
vibrations or in an unstable
location.
Do not move the recorder with its
mains lead connected.
Do not move the recorder for one
minute after you have unplugged
the mains lead.
Do not disconnect the mains lead
while the power is on.
Do not use the recorder in a place
subject to extreme changes in
temperature (temperature gradient
less than 10 °C/hour).
Do not attempt to change the hard
disk. This may result in a
malfunction. Should the hard disk
be damaged, you cannot recover
lost data. The hard disk is only a
temporary storage space.
The recorded contents of the hard
disk drive may be erased or
destroyed if the unit should
malfunction for whatever reason,
or if the hard disk drive is repaired,
modified or replaced. Note that the
contents of the recording cannot
be compensated for under any and
all conditions.
Copyrights
Television programmes, films,
video tapes, discs, and other
materials may be copyrighted.
Unauthorized recording of such
material may be contrary to the
provisions of the copyright laws.
Also, use of this recorder with
cable television transmission may
require authorization from the
cable television transmitter and/or
programme owner.
This product incorporates
copyright protection technology
that is protected by U.S. patents
and other intellectual property
rights. Use of this copyright
protection technology must be
authorized by Macrovision, and is
intended for home and other
limited viewing uses only unless
otherwise authorized by
Macrovision. Reverse engineering
or disassembly is prohibited.
Copy guard function
Since the recorder has a copy guard
function, programmes received
through an external tuner (not
supplied) may contain copy
protection signals (copy guard
function) and as such may not be
recordable, depending on the type of
signal.
If you have any questions or
problems concerning your recorder,
please consult your nearest Sony
dealer.
About this manual
In this manual, the internal hard
disk drive is written as “HDD,”
and “disc” is used as a general
reference for the HDD, DVDs, or
CDs unless otherwise specified by
the text or illustrations.
Instructions in this manual
describe the controls on the
remote. You can also use the
controls on the recorder if they
have the same or similar names as
those on the remote.
The on-screen display illustrations
used in this manual may not match
the graphics displayed on your TV
screen.
The explanations regarding DVDs
in this manual refer to DVDs
created on this recorder. The
explanations do not apply to
DVDs that are created on other
recorders and played back on this
recorder.
IMPORTANT NOTICE
Caution: This recorder is capable
of holding a still video image or
on-screen display image on your
television screen indefinitely. If
you leave the still video image or
on-screen display image
displayed on your TV for an
extended period of time you risk
permanent damage to your
television screen. Plasma display
panels and projection televisions
are especially susceptible to this.
Check your model name
The instructions in this manual
are for 2 models: RDR-HX900
and RDR-HX1000. Check your
model name by looking at the
front panel of the recorder.
4
Table of Contents
WARNING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
Ways to Use Your DVD Recorder . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
Quick Guide to Disc Types . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
Hookups and Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Hooking Up the Recorder . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
Step 1: Unpacking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
Step 2: Connecting the Aerial Cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
Step 3: Connecting the Video Cords . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
Step 4: Connecting the Audio Cords . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17
Step 5: Connecting the Mains Lead . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19
Step 6: Preparing the Remote . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19
Step 7: Easy Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22
Connecting a VCR or Similar Device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26
Connecting to a Satellite or Digital Tuner . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28
Connecting a PAY-TV/Canal Plus Decoder . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29
Guide to Displays . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Using the On-Screen Menus . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32
Using the Title List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .33
Using the “Disc Info” Screen (disc settings) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35
Checking the Play Information and Playing Time . . . . . . . . . . . . . . . . . . . . . . . . . . . .38
How to Enter Characters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .40
Recording . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
Before Recording . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .41
Timer Recording (Standard/VIDEO Plus+) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .42
Checking/Changing/Cancelling Timer Settings (Timer List) . . . . . . . . . . . . . . . . . . . .46
Recording Without the Timer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .48
Recording From Connected Equipment With a Timer (Synchro Rec) . . . . . . . . . . . .51
Recording From Connected Equipment Without a Timer . . . . . . . . . . . . . . . . . . . . . .52
Playback . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
Playing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .54
Chasing Playback/Simultaneous Rec and Play . . . . . . . . . . . . . . . . . . . . . . . . . . . . .60
Searching for a Title/Chapter/Track, etc. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .61
Playing MP3 Audio Tracks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .62
Editing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64
Before Editing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .64
Editing a Title . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .65
Creating and Editing a Playlist . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .68
5
Dubbing (HDD y DVD) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72
Before Dubbing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72
Dubbing a Single Title (Title Dub) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74
Dubbing Multiple Titles (Dub Selected Titles) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75
DV Dubbing (DV t HDD/DVD) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77
Before DV Dubbing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77
Recording an Entire DV Format Tape (One Touch Dubbing) . . . . . . . . . . . . . . . . . . . 79
Program Edit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80
Settings and Adjustments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83
Using the Setup Displays . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83
Aerial Reception and Language Settings (Settings) . . . . . . . . . . . . . . . . . . . . . . . . . . 84
Video Settings (Video) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88
Audio Settings (Audio) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91
Recording and Parental Control Settings (Features) . . . . . . . . . . . . . . . . . . . . . . . . . 93
Disc and Remote Control Settings/Factory Settings (Options) . . . . . . . . . . . . . . . . . . 96
Easy Setup
(Resetting the Recorder) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 98
Additional Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 99
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 99
Self-diagnosis Function
(When letters/numbers appear in the display) . . . . . . . . . . . . . . . . . . . . . . . . . . 104
Notes About This Recorder . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 104
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 105
About i.LINK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 106
Guide to Parts and Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 108
Glossary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 112
Language Code List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 114
Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 115
6
Ways to Use Your DVD Recorder
Quick access to recorded titles – Title List
, Display the Title List to see all of the titles
on the disc, including recording date,
channel, recording mode and thumbnail
image (page 33).
Play the beginning of a title while it is being recorded – Chasing Playback
, If you are using a DVD-RW (VR mode) or
the HDD, you can watch a programme from
the beginning while it is being recorded
(page 60).
Watching one title while recording another – Simultaneous Rec and Play
, If you are using a DVD-RW (VR mode) or
the HDD, you can watch a previously
recorded programme while recording
another programme on the same disc
(page 60).
1.5/4.7GB
Sort
Date
Title
Number
My Movies
TITLE LIST
ORIGINAL
1 AAB 13:00-14:00
Wed 5. 9 13:00 (1H00M) SP
2 DEF 20:00-21:00
Fri 17. 9 20:00 (1H00M) SLP
3 AAB 9:00-9:30
Sat 25. 9 9:00 (0H30M) EP
4 GHI 20:00-20:30
Sat 25. 9 20:00 (0H30M) SLP
AAB
DEF
AAB
GHI
Title List
Recording
The match isn’t over yet,
but I’ll start watching it
from the beginning now.
Recording
I think I’ll watch yesterday’s
golf match now, even though
I am recording a movie.
7
Creating your own programme – Playlist
, Record a programme on a DVD-RW (VR
mode), then delete, move and add scenes at
will to create your own, original
programme (page 68).
Copying a recorded title to and from the HDD – Dubbing (HDD y DVD)
, Create copies of your favourite titles for
safekeeping by dubbing them to a DVD, or
make a copy of your friend’s recordings by
dubbing them to the HDD (page 72).
Automatic dubbing of DV tapes – DV Dubbing (DV t HDD/DVD)
, Connect your digital video camera to the
DV IN jack and automatically dub the
entire contents or just selected scenes to a
DVD disc (page 77).
A list of recordable and playable discs is on page 8.
Original
Playlist
Dubbing
Control
Dubbing
8
Quick Guide to Disc Types
Recordable and playable discs
Usable disc versions (as of May 2004)
4x-speed or slower DVD+RWs
2x-speed or slower DVD-RWs (Ver.1.1, Ver.1.1
with CPRM*
1
)
8x-speed or slower DVD+Rs
8x-speed or slower DVD-Rs (Ver.2.0)
“DVD+RW,” “DVD-RW,” “DVD+R,” and “DVD-R,”
are trademarks.
*1
CPRM (Content Protection for Recordable Media) is
a coding technology that protects copyrights for
images.
*2
Only if the recording mode is SP, HSP, or HQ, and
“DVD Rec Picture Size” is set to “16:9.
*3
Erasing titles does not free up disc space.
Compatibility with
other DVD players
(finalizing)
Playable only on VR mode
compatible players
(finalization unnecessary)
Playable on most DVD
players (finalization
necessary) (page 37)
Playable on DVD+RW
compatible players
(automatically finalized)
Playable on most DVD
players (finalization
necessary) (page 37)
Playable on most DVD+R
compatible players (finalization
necessary) (page 37)
Format in VR
mode
(page 36)
Format in
Video mode
(page 36)
Automatically
formatted
(Formatting
unnecessary)
Automatically
formatted
Automatically
formatted
Formatting
(new discs)
Icon
used in
this
manual
Disc
Logo
Type
DVD-
RW
VR
mode
Video
mode
DVD+RW
Hard disk
drive
(internal)
DVD-R
DVD+R
-
RW
VR
-
RW
Video
+
RW
-
R
+
R
HDD
9
Yes
Yes
Yes
Yes
No
No
Yes
Yes
Yes
Yes
Yes
Yes
No
No
No
No
Yes
Yes *
2
No
Yes *
2
No
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes *
3
Yes *
3
Yes
No
Yes
No
No
Yes
No
No
Yes Yes Yes Yes Yes Yes No
No
No
Recording Features Editing Features
Rewrite
(page 41)
Auto
Chapter
(page 93)
Manual
Chapter
(page 68)
Record
16:9 sizes
(page 49)
Change
title name
(page 65)
Delete title
(page 66)
A-B Erase
(page 66)
Playlist
(page 68)
Discs that cannot be recorded on
4x-speed compatible DVD-RWs (Ver. 1.2/4x)
DVD-RWs (Ver.1.0)
DVD+RWs that are not 2.4x-speed compatible
Dual layer discs
8 cm discs
,continued
10
Playable discs
Discs that cannot be played
All CD-ROMs (including PHOTO CDs)
CD-Rs/CD-RWs, other than those recorded in
music CD format, MP3 format, or Video CD
format
Data part of CD-Extras
DVD-ROMs
DVD Audio discs
DVD-RAMs
HD layer on Super Audio CDs
DVD VIDEOs with a different region code
(page 11)
z Hint
This DVD recorder can play 8 cm CDs and 8 cm DVDs
as well.
Discs such as movies that can be purchased or rented
VIDEO CDs or CD-Rs/CD-RWs in
VIDEO CD/Super VIDEO CD format
Music CDs or CD-Rs/CD-RWs in music CD format
that can be purchased
CD-ROMs/CD-Rs/CD-RWs created on a PC or
similar device in music format containing MP3
audio tracks
Icon
used in
this
manual
Disc
Logo
VIDEO CD
CD
DATA CD
DVD VIDEO
Type Characteristics
DVD
VCD
CD
DATA CD
11
Note on playback operations of DVD VIDEOs/
VIDEO CDs
Some playback operations of DVD VIDEOs/
VIDEO CDs may be intentionally set by software
producers. Since this recorder plays DVD
VIDEOs/VIDEO CDs according to the disc
contents the software producers designed, some
playback features may not be available. Also, see
the instructions supplied with the DVD VIDEOs/
VIDEO CDs.
Region code (DVD VIDEO only)
Your recorder has a region code printed on the rear
of the unit and will only play DVD VIDEOs
(playback only) labelled with identical region
codes. This system is used to protect copyrights.
DVD VIDEOs labelled will also play on this
recorder.
If you try to play any other DVD VIDEO, the
message “Playback prohibited by region code.”
will appear on the TV screen. Depending on the
DVD VIDEO, no region code indication may be
labelled even though playing the DVD VIDEO is
prohibited by area restrictions.
Music discs encoded with copyright protection
technologies
This product is designed to play back discs that
conform to the Compact Disc (CD) standard.
Recently, various music discs encoded with
copyright protection technologies are being
marketed by some record companies. Please be
aware that among those discs, there are some that
do not conform to the CD standard and may not be
playable by this product.
Notes
Some DVD+RWs/DVD+Rs, DVD-RWs/DVD-Rs, or
CD-RWs/CD-Rs cannot be played on this recorder due
to the recording quality or physical condition of the
disc, or the characteristics of the recording device and
authoring software. The disc will not play if it has not
been correctly finalized. For more information, see the
operating instructions for the recording device.
You cannot mix VR mode and Video mode on the same
DVD-RW. To change the disc’s format, reformat the
disc (page 36). Note that the disc’s contents will be
erased after reformatting.
You cannot shorten the time required for recording
even with high-speed discs. Also, you cannot record on
the disc if the disc is not 1x speed compatible.
It is recommended that you use discs with “For Video”
printed on their packaging.
You cannot add new recordings to DVD-Rs or DVD-
RWs (Video mode) that contain recordings made on
other DVD equipment.
In some cases, you may not be able to add new
recordings to DVD+RWs that contain recordings made
on other DVD equipment. If you do add a new
recording, note that this recorder will rewrite the DVD
menu.
If the disc contains PC data unrecognizable by this
recorder, the data may be erased.
ALL
RDR–XXXX
00V 00Hz
00W
NO.
0-000-000-00
X
Region code
12
Hookups and Settings
Hooking Up the Recorder
Follow steps 1 to 7 to hook up and adjust the settings of the recorder.
Notes
Plug cords securely to prevent unwanted noise.
Refer to the instructions supplied with the components to be connected.
You cannot connect this recorder to a TV that does not have a SCART or video input jack.
Be sure to disconnect the mains lead of each component before connecting.
Step 1: Unpacking
Check that you have the following items:
Audio/video cord (pinplug × 3 y pinplug × 3) (1)
Mains lead (1)
Aerial cable (1)
Remote commander (remote) (1)
R6 (size AA) batteries (2)
13
Hookups and Settings
Step 2: Connecting the Aerial Cable
Connect the aerial cable by following the steps below. Do not connect the mains lead until you reach “Step
5: Connecting the Mains Lead” (page 19).
1 Disconnect the aerial cable from your TV and connect it to AERIAL IN on the rear panel of the
recorder.
2 Connect AERIAL OUT of the recorder to the aerial input of your TV, using the supplied aerial
cable.
AERIAL
IN
LINE 4 IN DIGITAL OUT
COAXIAL
OPTICAL
PCM/DTS/MPEG/
DOLBY DIGITAL
COMPONENT
VIDEO OUT
VIDEO
S VIDEO
AUDI OR L
LINE 2 OUT
VIDEO
S VIDEO
AUDIOR L
Y
P
B
/
C
B
P
R
/
C
R
~ AC IN
OUT
LINE 1 - TV LINE 3 / DECODER
AERIAL
IN
OUT
DVD recorder
TV
to AERIAL OUT
to AERIAL IN
Aerial cable (supplied)
: Signal flow
14
Step 3: Connecting the Video Cords
Select one of the following patterns A through D, according to the input jack on your TV monitor,
projector, or AV amplifier (receiver). This will enable you to view pictures. Audio connections are
explained in “Step 4: Connecting the Audio Cords” (page 17).
Note
Do not connect more than one type of video cord between the recorder and your TV at the same time.
VIDEO
AUDIO
INPUT
L
R
INPUT
S VIDEO
P
R
/C
R
P
B
/C
B
Y
COMPONENT
VIDEO IN
AERIAL
IN
LINE 4 IN DIGITAL OUT
COAXIAL
OPTICAL
PCM/DTS/MPEG/
DOLBY DIGITAL
COMPONENT
VIDEO OUT
VIDEO
S VIDEO
AUDIOR L
LINE 2 OUT
VIDEO
S VIDEO
AUDIOR L
Y
P
B /
CB
P
R /
CR
~ AC IN
OUT
LINE 1 - TV LINE 3 / DECODER
C
B
D
A
Audio/video
cord (supplied)
Component video
cord (not supplied)
(yellow)
TV, projector, or AV
amplifier (receiver)
TV, projector, or AV
amplifier (receiver)
(green)
S-video cord
(not supplied)
TV, projector, or AV
amplifier (receiver)
(red) (blue)
(green)
(blue)
(red)
: Signal flow
to COMPONENT
VIDEO OUT
to LINE 2 OUT (VIDEO)
to LINE 2 OUT (S VIDEO)
SCART cord (not
supplied)
To LINE 1 – TV
DVD recorder
TV
15
Hookups and Settings
A Connecting to a SCART input jack
Connect using a SCART cord (not supplied) to the
LINE 1-TV jack and your TV. Be sure to make the
connections firmly to avoid hum and noise.
See the operating instructions supplied with the
TV to be connected. Also, when you set “Line1
Output” to “S Video” or “RGB” in step 15 of Easy
Setup (page 22), use a SCART cord that conforms
to the selected signal.
B Connecting to a video input jack
Connect the yellow plug of the audio/video cord
(supplied) to the yellow (video) jack. You will
enjoy standard quality images.
Note that you cannot use the PROGRESSIVE
button with this connection.
C Connecting to an S VIDEO input
jack
Connect using an S-video cord (not supplied).
You will enjoy high quality images.
Note that you cannot use the PROGRESSIVE
button with this connection.
D Connecting to component video
input jacks (Y, P
B/CB, PR/CR)
Connect the component via the COMPONENT
VIDEO OUT jacks using a component video cord
(not supplied) or three video cords (not supplied)
of the same kind and length. You will enjoy
accurate colour reproduction and high quality
images.
If your TV accepts progressive 525p/625p format
signals, you must use this connection and set
“Component Out” in Video Setup to “On”
(page 89). Then press PROGRESSIVE on the
remote to send progressive video signals. For
details, see “Using the PROGRESSIVE button”
(page 16).
When playing “wide screen” images
Some recorded images may not fit your TV
screen. To change the aspect ratio, see page 88.
If you are connecting to a VCR
Connect your VCR to the LINE 3/DECODER
jack on the recorder (page 26).
Notes
When you connect the recorder to your TV via the
SCART jacks, the TV’s input source is set to the
recorder automatically when you start playback. If
necessary, press TV/DVD on the remote to return the
input to the TV.
For correct SMARTLINK connection, you will need a
SCART cord that has the full 21 pins. Refer to your
TV’s instruction manual as well for this connection.
If you connect this recorder to a TV with
SMARTLINK, set “Line1 Output” to “Video” in step
15 of Easy Setup.
About the SMARTLINK features
(for SCART connections only)
If the connected TV (or other connected
equipment such as a set top box) complies with
SMARTLINK, NexTView Link,
MEGALOGIC*
1
, EASYLINK*
2
,
CINEMALINK*
2
, Q-Link*
3
, EURO VIEW
LINK*
4
, or T-V LINK*
5
, this recorder
automatically runs the SMARTLINK function
after you complete the connection pattern A on
page 14 (the SMARTLINK indicator lights up
when you turn on your TV). You can enjoy the
following SMARTLINK features.
•Preset Download
You can download the tuner preset data from
your TV to this recorder, and tune the recorder
according to that data in Easy Setup. This
greatly simplifies the Easy Setup procedure. Be
careful not to disconnect the cables or exit the
Easy Setup function during this procedure
(page 22).
Yellow
White (L)
Red (R)
Yellow
White (L)
Red (R)
Green
Blue
Red
Green
Blue
Red
,continued
16
•TV Direct Rec
You can easily record what you are watching on
your TV (page 48).
One Touch Play
You can turn on the recorder and TV, set the
TV’s input to the recorder, and start playback
with one touch of the H (play) button
(page 55).
One Touch Menu
You can turn on the recorder and TV, set the TV
to the recorder’s channel, and display the Title
List menu with one touch of the TITLE LIST
button (page 55).
One Touch Timer
You can turn on the recorder and TV, set the TV
to the recorder’s channel, and display the timer
programming menu with one touch of the
TIMER button on the remote (page 44).
Automatic Power Off
The recorder will turn off automatically if the
recorder is not used after you turn off the TV.
NexTView Download
You can easily set the timer by using the
NexTView Download function on your TV.
See your TV’s instruction manual.
*1
“MEGALOGIC” is a registered trademark of Grundig
Corporation.
*2
“EASYLINK” and “CINEMALINK” are trademarks
of Philips Corporation.
*3
“Q-Link” is a trademark of Panasonic Corporation.
*4
“EURO VIEW LINK” is a trademark of Toshiba
Corporation.
*5
“T-V LINK” is a trademark of JVC Corporation.
z Hint
SMARTLINK also works with TVs or other equipment
having EPG Timer Control, EPG Title Download, and
Now Recording functions. For details, refer to the
operating instructions supplied with your TV or other
equipment.
Notes
The SMARTLINK features are available only when
“Video” is selected in “Line1 Output.”
The SMARTLINK features are not available for
devices connected via the DVD recorder’s LINE 3/
DECODER jack.
Not all TVs respond to the functions above.
Using the PROGRESSIVE button
By using the PROGRESSIVE button on the
remote, you can select the signal format in which
the recorder outputs video signals: interlace or
progressive. Connect the recorder using the
COMPONENT VIDEO OUT jacks (pattern D on
page 15), and set “Component Out” in Video
Setup to “On” (page 89). Then press the
PROGRESSIVE button. “PROGRESSIVE”
appears in the front panel display when the
recorder outputs progressive signals.
Progressive
Select this when:
your TV accepts progressive signals, and,
the TV is connected to the COMPONENT
VIDEO OUT jacks.
Note that the pictures will not be clear or no
picture will appear if you select progressive signal
output when either of the above conditions is not
met.
Interlace
Set to this position when:
your TV does not accept progressive signals, or,
your TV is connected to jacks other than the
COMPONENT VIDEO OUT jacks (LINE OUT
(VIDEO) or S VIDEO).
z Hint
When you select progressive signal output, you can fine-
tune the signal according to the type of software you are
watching (page 89).
Note
Consumers should note that not all high definition
television sets are fully compatible with this product and
may cause artifacts to be displayed in the picture. In the
case of 525/625 progressive scan picture problems, it is
recommended that the user switch the connection to the
‘standard definition’ output. If there are questions
regarding our TV set compatibility with this model 525p/
625p DVD recorder, please contact our customer service
centre.
17
Hookups and Settings
Step 4: Connecting the Audio Cords
Select one of the following patterns A or B, according to the input jack on your TV monitor, projector,
or AV amplifier (receiver).
This will enable you to listen to sound.
z Hint
For correct speaker location, see the operating instructions supplied with the connected components.
Note
Do not connect your TV’s audio output jacks to the LINE IN (AUDIO L/R) jacks at the same time. This will cause
unwanted noise to come from your TV’s speakers.
AERIAL
IN
LINE 4 IN DIGITAL OUT
COAXIAL
OPTICAL
PCM/DTS/MPEG/
DOLBY DIGITAL
COMPONENT
VIDEO OUT
VIDEO
S VIDEO
AUDIOR L
LINE 2 OUT
VIDEO
S VIDEO
AUDI OR L
Y
P
B /
CB
P
R /
CR
~ AC IN
OUT
LINE 1 - TV LINE 3 / DECODER
VIDEO
AUDIO
INPUT
L
R
B
A
DIGITAL OUT
COAXIAL
OPTICAL
PCM/DTS/MPEG/
DOLBY DIGITAL
LINE 2 OUT
VIDEO
S VIDEO
AUDIOR L
AV amplifier (receiver)
with a decoder
(red)
TV, projector, or AV
amplifier (receiver)
Audio/video
cord (supplied)
: Signal flow
Coaxial digital cord
(not supplied)
to DIGITAL OUT (COAXIAL or
OPTICAL)
to LINE 2 OUT (R-AUDIO-L)
Optical digital cord (not supplied)
Rear (L)
DVD recorder
(white)
(yellow)*
(yellow)
(white)
(red)
[Speakers]
Front (L)
[Speakers]
to coaxial
digital input
Rear (R)
Front (R)
Subwoofer
or
Centre
* The yellow plug is used for video signals (page 14).
to optical
digital input
,continued
18
A Connecting to audio L/R input
jacks
This connection will use your TV’s or stereo
amplifier’s (receiver’s) two speakers for sound.
Connect using the audio/video cord (supplied).
Surround effect (page 56)
TV: Dynamic, Wide, Night
Stereo amplifier (receiver): Standard, Night
Note
Do not connect the LINE 4 IN (R-AUDIO-L) and LINE
2 OUT (R-AUDIO-L) jacks to your TV’s audio output
jacks at the same time. This will cause unwanted noise to
come from your TV’s speakers.
B Connecting to a digital audio
input jack
If your AV amplifier (receiver) has a Dolby*
1
Digital, DTS*
2
, or MPEG audio decoder and a
digital input jack, use this connection.
Connect using a coaxial or optical digital cord (not
supplied).
Surround effect
Dolby Digital (5.1ch), DTS (5.1ch), MPEG audio
(5.1ch)
*1
Manufactured under license from Dolby Laboratories.
“Dolby,” “Pro Logic,” and the double-D symbol are
trademarks of Dolby Laboratories.
*2
“DTS” and “DTS Digital Out” are trademarks of
Digital Theater Systems, Inc.
Notes
After you have completed connection B, make the
appropriate settings under “Audio Connection” in Easy
Setup (page 22). If your AV amplifier (receiver) has an
MPEG audio decoder function, set “MPEG” to
“MPEG” in Audio Setup (page 92). Otherwise, no
sound or a loud noise will come from your speakers.
The surround sound effects of this recorder cannot be
used with connection B.
Yellow
White (L)
Red (R)
Yellow
White (L)
Red (R)
Coaxial cord
Optical cord
19
Hookups and Settings
Step 5: Connecting the
Mains Lead
Connect the supplied mains lead to the AC IN
terminal of the recorder. Then plug the recorder
and TV mains leads (power cords) into the mains.
After you connect the mains lead, you must wait
for a short while before operating the recorder.
You can operate the recorder once the front panel
display lights up and the recorder enters standby
mode.
If you connect additional equipment to this
recorder (page 26), be sure to connect the mains
lead after all connections are complete.
Step 6: Preparing the
Remote
You can control the recorder using the supplied
remote. Insert two R6 (size AA) batteries by
matching the 3 and # ends on the batteries to the
markings inside the battery compartment. When
using the remote, point it at the remote sensor
on the recorder.
Notes
If the supplied remote interferes your other Sony DVD
recorder or player, change the command mode number
for this recorder (page 21).
Use the batteries correctly to avoid possible leakage
and corrosion. Do not touch the liquid with bare hands
should leakage occur. Observe the following:
– Do not use a new battery with an old battery, or
batteries of different manufacturers.
– Do not attempt to recharge the batteries.
If you do not intend to use the remote for an extended
period of time, remove the batteries.
– If battery leakage occurs, wipe out any liquid inside
the battery compartment, and insert new batteries.
Do not expose the remote sensor (marked on the
front panel) to strong light, such as direct sunlight or
lighting apparatus. The recorder may not respond to the
remote.
~ AC IN
to mains
to AC IN
1
2
,continued
20
Controlling TVs with the remote
You can adjust the remote’s signal to control your
TV.
If you connected the recorder to an AV amplifier
(receiver), you can use the supplied remote to
control the AV amplifier’s (receiver’s) volume.
Notes
Depending on the connected unit, you may not be able
to control your TV or AV amplifier (receiver) with
some or all of the buttons below.
If you enter a new code number, the code number
previously entered will be erased.
When you replace the batteries of the remote, the code
number may be reset to the default setting. Set the
appropriate code number again.
1 Slide the TV/DVD switch to TV.
2 Hold down [/1.
3 Enter your TV’s manufacturer code (see
“Code numbers of controllable TVs”
below) using the number buttons.
4 Release [/1.
When the TV/DVD switch is set to TV, the
remote performs the following:
* If you use the number buttons to select the TV’s
programme position, press -/-- followed by the number
buttons for two-digit numbers.
To operate the TV/DVD button
(for SCART connections only)
The TV/DVD button switches between the
recorder and the last input source selected on the
TV. Point your remote at the recorder when using
this button. The button works even if the TV/DVD
switch is set to DVD.
When you connect the recorder to the TV via the
SCART jacks, the input source for the TV is set to
the recorder automatically when you start
playback. To watch another source, press the TV/
DVD button to switch the TV’s input source.
Code numbers of controllable TVs
If more than one code number is listed, try
entering them one at a time until you find the one
that works with your TV.
[/1 Turns your TV on or off
2 (volume) +/– Adjusts the volume of your
TV
PROG +/– Selects the programme
position on your TV
(wide mode) Switches to or from the
wide mode of a Sony wide-
screen TV
t (TV/video) Switches your TV’s input
source
1 2 3
4 5 6
7 8 9
0
TV/DVD
switch
"/1
2 +/–
Number buttons,
SET/-/--
t, TV/DVD
PROG +/–
Number buttons and
SET, -/--*
Selects the programme
position on your TV
Manufacturer Code number
Sony 01 (default)
Aiwa 01 (default)
Grundig 11
Hitachi 23, 24, 72
Loewe 06, 45
Nokia 15, 16, 69, 73
Panasonic 17, 49
Philips 06, 07, 08, 23, 45, 72
Saba 12, 13, 36, 43, 74, 75
Samsung 06, 22, 23, 71, 72
Sanyo 25
Sharp 29
Telefunken 12, 13, 36, 43, 74, 75
Thomson 12, 13, 43, 74, 75
Toshiba 38
LG 06
JVC 33
21
Hookups and Settings
Controlling the volume of your AV
amplifier (receiver) with the remote
1 Slide the TV/DVD switch to DVD.
2 Hold down [/1, and enter the
manufacturer code (see the table below)
for your AV amplifier (receiver) using the
number buttons.
3 Release [/1.
The 2 (volume) +/– buttons control the AV
amplifier’s volume.
If you want to control the TV’s volume, slide
the TV/DVD switch to TV.
z Hint
If you want to control the TV’s volume even when the
TV/DVD switch is set to DVD, repeat the steps above
and enter the code number 90 (default).
Code numbers of controllable AV amplifiers
(receivers)
If more than one code number is listed, try
entering them one at a time until you find the one
that works with your AV amplifier (receiver).
If you have a Sony DVD player or
more than one Sony DVD recorder
If the supplied remote interferes with your other
Sony DVD recorder or player, set the command
mode number for this recorder and the supplied
remote to one that differs from the other Sony
DVD recorder or player.
The default command mode setting for this
recorder and the supplied remote is DVD3.
1 Press SYSTEM MENU.
The System Menu appears.
2 Select “SETUP,” and press ENTER.
Manufacturer Code number
Sony 78, 79, 80, 91
Denon 84, 85, 86
Kenwood 92, 93
Onkyo 81, 82, 83
Pioneer 99
Sansui 87
Technics 97, 98
Yamaha 94, 95, 96
1 2 3
4 5 6
7 8 9
0
TV/DVD
switch
"/1
2 +/–
Number
buttons
1 2 3
4 5 6
7 8 9
0
SYSTEM
MENU
M/m,
ENTER
COMMAND
MODE
switch
O RETURN
SETUP
Settings
Video
Audio
Features
Options
Easy Setup
Channel Setting
Channel List
Clock
Language
,continued
22
3 Select “Options,” and press ENTER.
4 Select “Command Mode,” and press
ENTER.
5 Select the Command mode (DVD1, DVD2,
or DVD3), and press ENTER.
6 Slide the COMMAND MODE switch on the
remote so it matches the mode you
selected above.
To return to the previous step
Press O RETURN.
Step 7: Easy Setup
Follow the steps below to make the minimum
number of basic adjustments for using the
recorder. If you do not complete Easy Setup, it
will appear each time you turn on your recorder.
Settings are made in the following order.
m
m
m
m
m
m
1 Turn on the TV.
2 Press [/1.
The recorder turns on.
Settings
Video
Audio
Features
Options
Easy Setup
Format DVD :
HDD Bilingual Rec. :
DVD Bilingual Rec. :
Dimmer :
Auto Display :
Command Mode :
Factory Setup
VR
Main
Main
Normal
On
DVD3
SETUP
Settings
Video
Audio
Features
Options
Easy Setup
Format DVD :
HDD Bilingual Rec. :
DVD Bilingual Rec. :
Dimmer :
Auto Display :
Command Mode :
Factory Setup
VR
Main
Main
Normal
On
DVD3
SETUP
DVD1
DVD2
DVD3
OSD Language Setup
Tuner and Channel Setup
Clock Setup
TV Type Setup
Video Connection Setup
Audio Connection Setup
Finished!
1 2 3
4 5 6
7 8 9
0
"/1
</M/m/,,
ENTER
O RETURN
PROG +/–
23
Hookups and Settings
3 Switch the input selector on your TV so that
the signal from the recorder appears on
your TV screen.
“Initial settings necessary to operate the DVD
recorder will be made. You can change them
later using Setup. Before you start, check that
you have made all necessary connections.”
appears.
If this message does not appear, select “Easy
Setup” from “SETUP” in the System Menu
to run Easy Setup. For details, see “Settings
and Adjustments” (page 83).
4 Press ENTER.
The Setup Display for selecting the language
used in the on-screen display appears.
5 Select a language.
6 Press ENTER.
The Setup Display for selecting your country
and language for the tuner system appears.
The channel order will be set according to the
country or language you select.
7 Select your country or language.
If you live in a French speaking country that
is not listed on the display, select “ELSE.”
8 Press ENTER.
If you made connection A (page 14) and the
connected TV complies with
SMARTLINK, the Preset Download
function automatically starts.
If the Preset Download function does not
work or if you made a connection other than
A, the Auto Tuner Preset function
automatically starts searching for all of the
receivable channels and presets them.
To set the channels manually, see page 84.
9 After the download or search is complete,
the Clock function automatically starts.
Once the clock signal is received, the Setup
Display for selecting the aspect ratio of the
connected TV appears.
If the current time or date is not set, the
display for setting the clock manually
appears. Set the clock manually using </
M/m/,, and press ENTER.
OSD 1/9
Select the screen Language.
English
Français
Deutsch
Italiano
Español
Nederlands
Dansk
EASY SETUP
EASY SETUP
Tuner System 2/9
Select a country and
language.
L
N
NL
P
S
SF
UK
ELSE
– Français
– Dansk/Norsk
– Nederlands
– Português
– Svenska
– Suomi
– English
– English
EASY SETUP
Preset Download 3/9
Loading data from TV.
Please wait.
Prog. 1
EASY SETUP
Auto Tuner Preset 3/9
Searching for receivable channels.
Please wait.
Prog. 1
EASY SETUP
Clock 4/9
Searching for clock data.
Please wait.
,continued
24
10Select the setting that matches your TV
type.
“16:9”: For wide-screen TVs or standard TVs
with a wide screen mode.
“4:3 Letter Box”: For standard TVs.
Displays “wide screen” pictures with bands
on the upper and lower sections of the screen.
“4:3 Pan Scan”: For standard TVs.
Automatically displays “wide screen”
pictures on the entire screen and cuts off the
sections that do not fit.
For details, see “TV Type” on page 88.
11Press ENTER.
The Setup Display for the component out
jacks appears.
12Select an option.
Select “On” if you are using the
COMPONENT VIDEO OUT jacks.
Otherwise, select “Off.”
13Press ENTER.
The Setup Display for the LINE 3/DECODER
jack appears.
14Select an option.
Select “Yes” if you will connect a decoder to
the LINE 3/DECODER jack. Otherwise,
select “No.”
15Press ENTER.
The Setup Display for selecting the type of
video signal output from the LINE 1-TV jack
appears.
16Select the type of signal you want to output
from the LINE1-TV jack.
“Video”: Outputs video signals.
“S Video”: Outputs S video signals.
“RGB”: Outputs RGB signals.
Note that if you select “On” in step 12, you
cannot select “RGB,” and that if you select
“Yes” in step 14, you cannot select “S Video.”
If you select “S Video” or “RGB,
SMARTLINK will be deactivated.
17Press ENTER.
The Setup Display for selecting the type of
jack used to connect to your amplifier
(receiver) appears.
18Select the type of jack (if any) you are
using to connect to an amplifier (receiver),
and press ENTER.
If you did not connect an AV amplifier
(receiver), select “No,” then go to step 22.
If you connected an AV amplifier (receiver)
using just an audio cord, select “Yes: LINE
OUT (R-AUDIO-L),” then go to step 22.
If you connected an AV amplifier (receiver)
using either a digital optical or coaxial cord,
select “Yes: DIGITAL OUT.”
19Select the type of Dolby Digital signal you
wish to send to your amplifier (receiver).
If your AV amplifier (receiver) has a Dolby
Digital decoder, select “Dolby Digital.”
Otherwise, select “D-PCM.”
EASY SETUP
TV Type 5/9
Select your TV screen type.
16 : 9
4 : 3 Letter Box
4 : 3 Pan Scan
EASY SETUP
Line1 Output 8/9
Select the Line1 output signal.
Video
S Video
RGB
EASY SETUP
Audio Connection 9/9
Is this recorder connected to an amplifier (receiver)?
Select the type of jack you are using.
Yes :
LINE OUT(R-AUDIO-L)
Yes :
DIGITAL OUT
No
Audio Connection 9/9
Dolby Digital
D-PCM
Dolby Digital
EASY SETUP
25
Hookups and Settings
20Press ENTER.
The Setup Display for the DTS signal appears.
21Select whether or not you wish to send a
DTS signal to your amplifier (receiver),
and press ENTER.
If your AV amplifier (receiver) has a DTS
decoder, select “On.” Otherwise, select “Off.”
22Press ENTER when “Finish” appears.
Easy Setup is finished. All connections and
setup operations are complete.
To return to the previous step
Press O RETURN.
z Hints
If your AV amplifier (receiver) has an MPEG audio
decoder, set “MPEG” to “MPEG” (page 92).
If you want to run Easy Setup again, select “Easy
Setup” in the Setup Display (page 98).
Note
To record TV programmes using the timer, you must set
the clock accurately.
Audio Connection 9/9
DTS
On
Off
EASY SETUP
EASY SETUP
Easy Setup is finished.
Finish
26
Connecting a VCR or Similar Device
After disconnecting the recorder’s mains lead from the mains, connect a VCR or similar recording device
to the LINE IN jacks of this recorder.
Use the DV IN jack on the front panel if the equipment has a DV output jack (i.LINK jack) (page 77).
See also the instruction manual supplied with the connected equipment.
To record on this recorder, see “Recording From Connected Equipment Without a Timer” (page 52).
Connecting to the LINE 3 jack
Connect a VCR or similar recording device to the LINE 3/DECODER jack of this recorder.
Notes
Pictures containing copy protection signals that prohibit any copying cannot be recorded.
If you pass the recorder signals via the VCR, you may not receive a clear image on your TV screen.
Be sure to connect your VCR to the DVD recorder and your TV in the order shown below. To watch video tapes,
watch the tapes through a second line input on your TV.
The SMARTLINK features are not available for devices connected via the DVD recorder’s LINE 3/DECODER jack.
When you record to a VCR from this DVD recorder, do not switch the input source to TV by pressing the TV/DVD
button on the remote.
If you disconnect the recorder’s mains lead, you will not be able to view the signals from the connected VCR.
AERIAL
IN
LINE 4 IN DIGITAL OUT
COAXIAL
OPTICAL
PCM/DTS/MPEG/
DOLBY DIGITAL
COMPONENT
VIDEO OUT
VIDEO
S VIDEO
AUDI OR L
LINE 2 OUT
VIDEO
S VIDEO
AUDIOR L
Y
P
B /
CB
P
R /
CR
~ AC IN
OUT
LINE 1 - TV LINE 3 / DECODER
TV
DVD recorder
to i
LINE1-TV
VCR
to i LINE
3/DECODER
SCART cord
(not supplied)
to SCART input
VCRDVD recorder TV
VCR DVD recorder TV
Line input 1
Line input 2
27
Hookups and Settings
Connecting to the LINE 2 IN or LINE 4 IN jacks
Connect a VCR or similar recording device to the LINE 2 IN or LINE 4 IN jacks of this recorder. If the
equipment has an S-video jack, you can use an S-video cord instead of an audio/video cord.
z Hint
When the connected equipment outputs only monaural sound, use audio cables that distribute monaural sounds to left/
right channels (not supplied).
Notes
Do not connect the yellow LINE IN (VIDEO) jack when using an S-video cord.
Do not connect the output jack of this recorder to another equipment’s input jack with the other equipment’s output
jack connected to the input jack of this recorder. Noise (feedback) may result.
Do not connect more than one type of video cord between the recorder and your TV at the same time.
AERIAL
IN
LINE 4 IN DIGITAL OUT
COAXIAL
OPTICAL
PCM/DTS/MPEG/
DOLBY DIGITAL
COMPONENT
VIDEO OUT
VIDEO
S VIDEO
AUDI OR L
LINE 2 OUT
VIDEO
S VIDEO
AUDI OR L
Y
P
B
/
C
B
P
R
/
C
R
~ AC IN
OUT
LINE 1 - TV LINE 3 / DECODER
OUTPUT
S VIDEO
AUDIO
LR
VIDEO
VCR, etc.
Audio/video cord
(supplied)
S-video
cord (not
supplied)
to LINE 2 IN DVD recorder (front)
: Signal flow
(rear)
to LINE 4 IN
VCR, etc.
28
Connecting to a Satellite or Digital Tuner
Connect a satellite or digital tuner to this recorder using the LINE 3/DECODER jack. Disconnect the
recorder’s mains lead from the mains when connecting the tuner.
To use the Synchro-Rec function, see below.
If the satellite tuner can output RGB signals
This recorder accepts RGB signals. If the satellite
tuner can output RGB signals, connect the TV
SCART connector on the satellite tuner to the
LINE 3/DECODER jack, and set “Line3 Input” of
“Scart Setting” to “Video/RGB” in Video Setup
(page 90). Note that this connection and setup
disable the SMARTLINK function. If you want to
use the SMARTLINK function with a compatible
set top box, see the instructions supplied with the
set top box.
If you want to use the Synchro Rec function
This connection is necessary to use the
Synchronized Recording function. See
“Recording From Connected Equipment With a
Timer (Synchro Rec)” (page 51).
Set “Line3 Input” of “Scart Setting” in Video
Setup (page 90) according to the specifications of
your satellite tuner. See your satellite tuner’s
instructions for more information.
If you are using a B Sky B tuner, be sure to
connect the tuner’s VCR SCART jack to the LINE
3/DECODER jack. Then set “Line3 Input” of
“Scart Setting” according to the specifications of
the VCR SCART jack on your satellite tuner.
Notes
Do not set “Line3 Input” of “Scart Setting” in Video
Setup to “Decoder.”
Synchronized Recording does not work with some
tuners. For details, see the tuner’s operating
instructions.
If you disconnect the recorder’s mains lead, you will
not be able to view the signals from the connected
tuner.
AERIAL
IN
LINE 4 IN DIGITAL OUT
COAXIAL
OPTICAL
PCM/DTS/MPEG/
DOLBY DIGITAL
COMPONENT
VIDEO OUT
VIDEO
S VIDEO
AUDI OR L
LINE 2 OUT
VIDEO
S VIDEO
AUDIOR L
Y
P
B /
CB
P
R /
CR
~ AC IN
OUT
LINE 1 - TV LINE 3 / DECODER
TV
to SCART input
SCART cord
(not supplied)
Satellite tuner, etc.
to i
LINE1-TV
to i LINE
3/DECODER
DVD recorder
29
Hookups and Settings
Connecting a PAY-TV/Canal Plus Decoder
You can watch or record PAY-TV/Canal Plus programmes if you connect a decoder (not supplied) to the
recorder. Disconnect the recorder’s mains lead from the mains when connecting the decoder.
Connecting a decoder
AERIAL
IN
LINE 4 IN DIGITAL OUT
COAXIAL
OPTICAL
PCM/DTS/MPEG/
DOLBY DIGITAL
COMPONENT
VIDEO OUT
VIDEO
S VIDEO
AUDI OR L
LINE 2 OUT
VIDEO
S VIDEO
AUDI OR L
Y
P
B /
CB
P
R /
CR
~ AC IN
OUT
LINE 1 - TV LINE 3 / DECODER
TV
Aerial cable
(supplied)
SCART cord
(not supplied)
PAY-TV/Canal
Plus decoder
to AERIAL
OUT
to i LINE 3/DECODER
DVD recorder
to AERIAL IN
to SCART input
SCART cord (not
supplied)
to i
LINE1-TV
,continued
30
Setting PAY-TV/Canal Plus channels
To watch or record PAY-TV/Canal Plus
programmes, set your recorder to receive the
channels using the on-screen display.
In order to set the channels correctly, be sure to
follow all of the steps below.
1 Press SYSTEM MENU.
The System Menu appears.
2 Select “SETUP,” and press ENTER.
3 Select “Video,” and press ENTER.
4 Select “Scart Setting,” and press ENTER.
5 Press M/m to select “Video” or “RGB” for
“Line1 Output,” “Decoder” for “Line3
Input,” and “Video” for “Line3 Output,”
and press ENTER.
The Video Setup display appears again.
6 Press O RETURN to return the cursor to
the left column.
7 Select “Settings,” and press ENTER.
8 Select “Channel Setting,” and press
ENTER.
9 Press PROG +/– to select the desired
programme position.
1 2 3
4 5 6
7 8 9
0
SYSTEM
MENU
O RETURN
PROG +/–
</M/m/,,
ENTER
Settings
Video
Audio
Features
Options
Easy Setup
Channel Setting
Channel List
Clock
Language
SETUP
Settings
Video
Audio
Features
Options
Easy Setup
SETUP
TV Type :
Pause Mode :
Component Out :
Progressive Mode :
Screen Saver :
Scart Setting
Line4 Input :
16 : 9
Auto
Off
Auto
On
Video
Video - Scart Setting
Line1 Output Line3 Input Line3 Output
Video
Video
Video
S Video
S Video
RGB
Video/RGB
Video/RGB
Decoder
S Video
S Video
Video/RGB
Video
S Video
Video
Video
S Video
Video
Settings
Video
Audio
Features
Options
Easy Setup
Channel Setting
Channel List
Clock
Language
SETUP
Settings - Channel Setting
Prog. 8
System :
Normal / CATV :
Channel Set :
Station Name :
PAY - TV / CANAL+ :
Audio :
BG
Normal
C2
CDE
Off
NICAM
Settings - Channel Setting
Prog. 6
System :
Normal / CATV :
Channel Set :
Station Name :
PAY - TV / CANAL+ :
Audio :
BG
Normal
C24
PQR
Off
NICAM
Selected programme position
31
Hookups and Settings
10Select “System,” and press ENTER.
11Press M/m to select an available TV
system, BG, DK, I, or L, and press ENTER.
To receive broadcasts in France, select “L.”
12Select “Normal/CATV,” and press ENTER.
13Select “Normal,” and press ENTER.
To preset CATV (Cable Television) channels,
select “CATV.”
14Select “Channel Set,” and press ENTER.
15Select the PAY-TV/Canal Plus channel,
and press ENTER.
16Select “PAY-TV/CANAL+,” and press
ENTER.
17Select “On,” and press ENTER.
To return to the previous step
Press O RETURN.
Notes
When you set “Line3 Input” to “Decoder” in step 5
above, you will not be able to select “L3” because Line
3 will become a dedicated line for the decoder.
If you disconnect the recorder’s mains lead, you will
not be able to view the signals from the connected
decoder.
Settings - Channel Setting
Prog. 6
System :
Normal / CATV
Channel Set :
Station Name :
PAY - TV / CANAL+ :
Audio :
BG
Normal
C1
ARD
On
NICAM
BG
DK
I
L
Settings - Channel Setting
Prog. 6
System :
Normal / CATV :
Channel Set :
Station Name :
PAY - TV / CANAL+ :
Audio :
BG
Normal
C1
PQR
Off
NICAM
Normal
CATV
Settings - Channel Setting
Prog. 6
System :
Normal / CATV :
Channel Set :
Station Name :
PAY - TV / CANAL+ :
Audio :
BG
Normal
C1
PQR
Off
NICAM
C24
Settings - Channel Setting
Prog. 6
System :
Normal / CATV :
Channel Set :
Station Name :
PAY - TV / CANAL+ :
Audio :
BG
Normal
C24
PQR
On
NICAM
On
Off
32
Guide to Displays
Using the On-Screen Menus
This section introduces the System Menu, TOOLS
menu, and sub-menu. By using these displays, you
can perform most of the recorder’s operations.
System Menu
The System Menu appears when you press
SYSTEM MENU, and provides entries to all of
the recorder’s main functions, such as timer
recording and setup.
Select an option by pressing M/m and ENTER.
A TITLE LIST (page 33):
Turns on the Title List menu, which shows
recorded titles on the disc.
B TIMER (page 42):
Allows you to set a new timer recording
setting.
C TIMER LIST (page 46):
Turns on the Timer List menu, which allows
you to check, change, or cancel timer settings.
D DV EDIT (page 77):
Activates the DV Edit function, which allows
you to record and edit the contents of a DV
format tape.
E DUBBING (page 72):
Dubs titles from the HDD to a DVD and vice
versa. Select the dubbing direction before
dubbing.
F SETUP (page 83):
Turns on the Setup Display, which allows you
to set up the recorder to suit your preferences.
Sub-menu
The sub-menu appears when you select an item
from a list menu (e.g. a title from the Title List
menu), and press ENTER. The sub-menu displays
options applicable only to the selected item. The
displayed options differ depending on the
situation and disc type.
Select an option by pressing M/m and ENTER.
Example: The Title List menu
+
R
DVD
VCD
CD
DATA CD
-
RW
VR
-
RW
Video
+
RW
-
R
HDD
1 2 3
4 5 6
7 8 9
0
Number
buttons, SET
TOOLS
</M/m/,,
ENTER
SYSTEM
MENU
O RETURN
SYSTEM MENU
TITLE LIST
TIMER
TIMER LIST
DV EDIT
DUBBING
SETUP
1 AAB 13:00-14:00
2 DEF 20:00-21:00
3 AAB 9:00- 9:30
4 GHI 20:00-20:30
5 DEF 20:00-20:30
6 L3 21:00-21:30
7 L3 21:00-21:30
8 GHI 10:00-10:30
15. 9
17. 9
25. 9
25. 9
15.10
19.10
26.10
28.10
Wed
Fri
Sat
Sat
Fri
Tu e
Tu e
Thu
Sort
1.5/4.7GB
My Movies
TITLE LIST
ORIGINAL
Date
Title
Number
Close
Play
Play Beginning
Erase
Dubbing
Protect
Title Name
Set Thumbnail
A-B Erase
Options for
the selected
item
33
Guide to Displays
TOOLS
The TOOLS menu appears when you press
TOOLS, and displays options applicable to the
entire disc (e.g. disc protection), recorder (e.g.
audio settings during recording), or multiple items
on a list menu (e.g. erasing multiple titles). The
displayed options differ depending on the
situation and disc type.
Select the option by pressing M/m and ENTER.
Example 1: When you press TOOLS while the
Title List menu is turned on.
Example 2: When you press TOOLS while a
DVD-RW (VR mode) is playing.
To return to the previous display
Press O RETURN.
Using the Title List
The title of programmes recorded on a disc is
displayed in the Title List.
1 Press HDD or DVD.
If you select DVD, press Z (open/close) and
place a DVD on the disc tray. Press Z again
to close the disc tray.
Wait until “LOAD” disappears from the front
panel display.
2 Press TITLE LIST.
To show the list in greater detail (zoom), press
ZOOM+.
1 AAB 13:00-14:00
2 DEF 20:00-21:00
3 AAB 9:00- 9:30
4 GHI 20:00-20:30
5 DEF 20:00-20:30
6 L3 21:00-21:30
7 L3 21:00-21:30
8 GHI 10:00-10:30
15. 9
17. 9
25. 9
25. 9
15.10
19.10
26.10
28.10
Wed
Fri
Sat
Sat
Fri
Tu e
Tu e
Thu
Sort
1.5/4.7GB
My Movies
TITLE LIST
ORIGINAL
Date
Title
Number
TOOLS
Close
Disc Info
Erase Titles
Dub Selected Titles
Playlist
Options for the disc or menu
TOOLS
Close
Stop
Disc Info
Erase
Protect
Options for the disc or picture
+
RW
-
RW
VR
-
RW
Video
-
R
+
R
HDD
1 2 3
4 5 6
7 8 9
0
Z
TOOLS
ZOOM +/–
CURSOR
MODE
</M/m/,,
ENTER
HDD DVD
TITLE LIST
With the recording side facing down
,continued
34
Standard Title List (Example: DVD-RW in VR
mode)
“Zoomed” Title List
A Disc type:
Displays a media type, HDD or DVD.
Also displays the title type (Original or
Playlist) for DVD-RWs (VR mode).
B Sort buttons:
Sorts the title order (see below).
C Zooming indicator:
Shows the current zoom status.
D Disc name (DVD only) (page 36)
E Disc space (remainder/total)
F Title information:
Displays the title number, title name, and
recording date.
z (red): Indicates that the title is currently
being recorded.
: Indicates that the title is currently being
dubbed.
: Indicates the protected title.
“NEW” (or N): Indicates that the title is newly
recorded (not played back) (HDD only).
: Indicates that the Update function is set
(HDD only) (page 42).
G Scroll bar:
Appears when all of the titles do not fit on the
list. To view the hidden titles, press M/m.
H Title’s thumbnail picture
To scroll the list display by page (Page mode)
Press CURSOR MODE while the list display is
turned on. The display enters Page mode. Each
time you press M/m, the entire Title List changes
to the next/previous page of titles.
To return to the Cursor mode, press CURSOR
MODE again.
About the Title List for DVD-RWs (VR mode)
You can switch the Title List to show Original or
Playlist.
While the Title List menu is turned on, press
TOOLS and select either “Original” or “Playlist,”
and press ENTER. “PLAYLIST” appears on the
front panel display when “Playlist” is selected.
For details, see “Edit options for DVD-RWs (VR
mode)” (page 64).
To change the title order (Sort)
Press < while the Title List menu is turned on to
move the cursor to the Sort column. Press M/m to
select the item, and press ENTER.
To change a title thumbnail picture
(Thumbnail) (HDD/DVD-RW in VR mode only)
You can select a favourite scene for the thumbnail
picture shown in the Title List menu.
1 Press TITLE LIST while a disc is in the
recorder and press ZOOM+.
2 Select a title whose thumbnail picture you
want to change, and press ENTER.
3 Select “Set Thumbnail” from the sub-menu,
and press ENTER.
The selected title starts to play in the
background.
1 AAB 13:00-14:00
2 DEF 20:00-21:00
3 AAB 9:00- 9:30
4 GHI 20:00-20:30
5 DEF 20:00-20:30
6 L3 21:00-21:30
7 L3 21:00-21:30
8 GHI 10:00-10:30
15. 9
17. 9
25. 9
25. 9
15.10
19.10
26.10
28.10
Wed
Fri
Sat
Sat
Fri
Tu e
Tu e
Thu
Sort
1.5/4.7GB
My Movies
TITLE LIST
ORIGINAL
Date
Title
Number
m
1.5/4.7GB
Sort
Date
Title
Number
My Movies
TITLE LIST
ORIGINAL
1 AAB 13:00-14:00
Wed 5. 9 13:00 (1H00M) SP
2 DEF 20:00-21:00
Fri 17. 9 20:00 (1H00M) SLP
3 AAB 9:00-9:30
Sat 25. 9 9:00 (0H30M) EP
4 GHI 20:00-20:30
Sat 25. 9 20:00 (0H30M) SLP
AAB
DEF
AAB
GHI
Order Sorted
New
(HDD only)
in order of when the titles were
recorded. The title that is recorded
most recently and not played back is
listed at the top.
Date in order of when the titles were
recorded. The title that is recorded
most recently is listed at the top.
Title in alphabetical order.
Number in order of recorded title number.
35
Guide to Displays
4 While watching the playback picture, press
H, X, or m/M to select the scene you
want to set for a thumbnail picture, and press
ENTER.
The scene is set for the title’s thumbnail
picture.
To turn off the Title List
Press TITLE LIST.
z Hint
After recording, the first scene of the recording (the title)
is automatically set as the thumbnail picture.
Notes
The Title List may not appear for DVDs created on
other DVD recorders.
The letters that cannot be displayed are replaced with
*
.”
Title thumbnail pictures are displayed only on this
recorder.
It may take a few seconds for the thumbnail pictures to
be displayed.
After editing, the title thumbnail picture may change to
the first scene of the recording (title).
After dubbing, the title thumbnail picture set on the
source recording is cancelled.
Using the “Disc Info”
Screen (disc settings)
With the Disc Information display, you can check
the disc type and remaining disc space. Also, you
can perform operations such as formatting and
finalizing (page 36).
1 Press HDD or DVD.
If you select a DVD, press Z (open/close) and
place a DVD on the disc tray. Press Z again
to close the disc tray.
Wait until “LOAD” disappears from the front
panel display.
2 Press TOOLS.
The TOOLS menu appears.
3 Select “Disc Info,” and press ENTER.
Items in the display differ depending on the
disc type or recording format.
+
RW
-
RW
VR
-
RW
Video
-
R
+
R
HDD
1 2 3
4 5 6
7 8 9
0
TOOLS
</M/m/,,
ENTER
Z
HDD
DVD
With the recording side facing down
,continued
36
Example: DVD-RW (VR mode)
A “Disc Name” (DVD only)
B “Media”: Disc type
C “Format”: Recording format type (DVD-
RW only)
D “Title no.”: Total number of titles
E “Protected”: Indicates whether protection is
set (DVD-RW in VR mode only)
F “Date”: Dates of when the oldest and the
most recent titles were recorded (DVD
only)
G “Continuous Rem. Time”/“Remainder
(approximate)
The longest continuous recording time in
each of the recording modes
Disc space bar
Remaining disc space/total disc space
H Disc setting buttons (page 36)
“Disc Name”
“Protect Disc”
“Finalize”/“Unfinalize”
“Erase All”
“Format”
Available settings differ depending on the
disc type.
z Hint
For DVD+RWs and DVD-RWs (Video mode), you can
check free space and title location on the disc using the
Disc Map display (page 67).
Note
On this model, 1 GB (read “gigabyte”) is equivalent to 1
billion bytes. The larger the number, the larger the disc
space.
Labelling, protecting, or formatting
a disc
You can execute options effective for the entire
disc using the Disc Information display.
1 Press TOOLS while the disc is in the
recorder.
The TOOLS menu appears.
2 Select “Disc Info,” and press ENTER.
Example: When the inserted disc is a DVD-
RW (VR mode).
3 Select an option, and press ENTER.
“Disc Name” (DVD only): Labels a DVD.
Enter the disc name in the “Input Disc Name”
display (page 40).
“Protect Disc” (DVD-RW in VR mode only):
Protects all titles on the disc. To cancel the
protection, select “Don’t Protect.”
“Erase All” (HDD/DVD+RW/DVD-RW
only): Erases all titles on the disc (except the
protected titles).
“Format” (HDD/DVD+RW/DVD-RW only):
Erases all contents of the disc to make a blank
disc. For DVD-RWs, select a recording
format (VR or Video) according to your
needs.
z Hints
You can set protection for individual titles (page 65).
By reformatting, you can change the recording format
on DVD-RWs, or record again on DVD-RWs (Video
mode) that have been finalized.
Note
You can enter up to 64 characters for a DVD’s disc name.
The disc name may not appear when the disc is played on
other DVD equipment.
Disc Information
DiscName Movie
Close
Media DVD-RW Format VR
Title no. Original 3 / Playlist 2
Protected Not Protected
Date 15.9.2003 ~ 28.10.2003
HQ : 0H30M
LP : 1H30M
HSP : 0H45M
EP : 2H00M
SP : 1H00M
2. 3 / 4. 7GB
SLP : 3H00M
Remainder
Disc Name
Format
Erase All
Finalize
Protect Disc
+
RW
-
RW
VR
-
RW
Video
-
R
+
R
HDD
Disc Information
DiscName
Close
Media DVD-RW Format VR
Title no. Original 3 / Playlist 2
Protected Not Protected
Date 15. 9. 2003 ~ 28. 10. 2003
HQ : 0H30M
LP : 1H30M
HSP : 0H45M
EP : 2H00M
SP : 1H00M
2. 3 / 4. 7GB
SLP : 3H00M
Remainder
Disc Name
Format
Erase All
Finalize
Protect Disc
37
Guide to Displays
Finalizing a DVD (preparing a disc
for playback on other equipment)
Finalizing is necessary when you play discs
recorded with this recorder on other DVD
equipment.
When you finalize a DVD+RW, DVD-RW
(Video mode), DVD+R, or DVD-R, a DVD menu
will be automatically created, which can be
displayed on other DVD equipment.
Before finalizing, check the differences between
the disc types in the table below.
Differences between the disc types
1 Press TOOLS while the disc is in the
recorder.
The TOOLS menu appears.
2 Select “Disc Info,” and press ENTER.
The Disc Information display appears.
3 Select “Finalize,” and press ENTER.
The display shows the approximate time
required for finalizing and asks for
confirmation.
4 Select “OK,” and press ENTER.
The recorder starts finalizing the disc.
To unfinalize a DVD-RW (VR mode)
If you cannot record or edit on a DVD-RW (VR
mode) that has been finalized with other DVD
equipment (a message appears), unfinalize the
disc by selecting “Unfinalize” in step 3 above.
z Hint
You can check whether the disc has been finalized or not.
If you cannot select “Finalize” in step 3 above, the disc
has already been finalized.
Notes
Depending on the condition of the disc, recording, or
the DVD equipment, discs may not play even if the
discs are finalized.
The recorder may not be able to finalize the disc if it
was recorded on another recorder.
Discs are automatically finalized when
removed from the recorder. However,
you may need to finalize the disc for
certain DVD equipment, or if the
recording time is short. You can edit or
record on the disc even after finalizing.
Finalizing is unnecessary when playing
a disc on VR format compatible
equipment.
Even if your other DVD equipment is
VR format compatible, you may need to
finalize the disc, especially if the
recording time is short. You can edit or
record on the disc even after finalizing.
Finalizing is necessary when playing on
any equipment other than this recorder.
After finalizing, you cannot edit or
record on the disc. If you want to record
on it again, reformat the disc (page 36).
However, all recorded contents will be
erased.
Finalizing is necessary when playing on
any equipment other than this recorder.
After finalizing, you cannot edit or
record on the disc.
+
RW
-
RW
VR
-
RW
Video
-
R
+
R
+
RW
-
RW
VR
-
RW
Video
+
R
-
R
Finalize
About xx min is needed for finalizing this disc.
Cannot cancel finalizing during transaction.
Do you want to finalize?
OK Cancel
38
Checking the Play
Information and Playing
Time
You can check the playing time and remaining
time of the current title, chapter, or track. Also,
you can check the disc name recorded on the
DVD/CD.
Press DISPLAY repeatedly.
Each time you press the button, the display
changes as follows:
The displays differ depending on the disc type or
playing status.
Display 1
Example: When playing a DVD VIDEO
A Title number/name
(Track number for CDs/VIDEO CDs without
PBC, scene number for VIDEO CDs with
PBC, track number/name for DATA CDs)
B Available functions for DVD VIDEOs
( angle/ audio/ subtitle, etc.)
C The current selected function or audio
setting (appears only temporarily)
D The current selected angle
Example: Dolby Digital 5.1 ch
Display 2
Example: When playing a DVD-RW (VR mode)
A Disc type*
2
/format (page 8)
B Title type (Original or Playlist) (page 64)
C Play mode
D Recording mode (page 41)
E Playing status bar*
3
F Title number (chapter number*
1
) (page 61)
(Track number for CDs/VIDEO CDs without
PBC, scene number for VIDEO CDs with
PBC, track number (album number*
1
) for
DATA CDs)
G CD text (album name) appears when text is
recorded on a CD.
H Playing time (remaining time*
1
)
*
1
Displayed when you press TIME/TEXT repeatedly.
*
2
Displays Super VCDs as “SVCD,” DATA CDs as
“CD.”
*
3
Does not appear with VIDEO CDs, and DATA CDs.
+
R
DVD
VCD
CD
DATA CD
-
RW
VR
-
RW
Video
+
RW
-
R
HDD
1 2 3
4 5 6
7 8 9
0
TIME/TEXT
DISPLAY
Title/track information (Display 1)
Play mode/time information (Display 2)
(Display off)
m
m
Title 1
1 : English DolbyDigital 2/0Angle3(5)
1 : English DolbyDigital 3/2.1
R
ear
(L/R)
Front (L/R) + Centre
LFE (Low Frequency
Effect)
0:00:45
T1SP
Original
DVD -RW
VR
Movies
39
Guide to Displays
z Hints
If “DTS” is set to “Off” in Audio Setup, the DTS track
selection option will not appear on the screen even if
the disc contains DTS tracks (page 92).
When “Auto Display” is set to “On” (default) in
Options Setup (page 97), playback information
automatically appears when the recorder is turned on,
etc.
Notes
The recorder can only display the first level of a CD’s
text, such as the disc name.
The letters or symbols that cannot be displayed are
replaced with “*.”
Checking the playing/remaining
time
You can view the playing or time information
displayed on the TV screen and the front panel
display.
Press TIME/TEXT repeatedly.
The displays differ depending on the disc type or
playing status.
Front panel display
Example: When playing a DVD
Example: When dubbing a DVD
Example: When playing a CD
Notes
The recorder can only display the first level of a CD’s
text, such as the disc name.
The letters or symbols that cannot be displayed are
replaced with “*.”
Playing time of MP3 audio tracks may not be displayed
correctly.
Playing time and number of the current title
Remaining time of the current title
Playing time and number of the current chapter
Remaining time of the current chapter
CH
Remaining time of dubbing in progress
Track playing time and the current track/index
number
Remaining time of the current track
Remaining time of the disc
CD text (when available)
Playing time of the disc
m
m
m
m
40
How to Enter Characters
You can label a DVD, title, or program by entering
characters. You can enter up to 64 characters for a
title or disc name, but the actual number of
characters displayed in the menus such as the Title
List will vary. When the display for entering
characters appears, follow the steps below.
1 Press </M/m/, to move the cursor to
the right of the screen and select “A”
(upper-case), “a” (lower-case), or
“Symbol,” and press ENTER.
The characters of the selected type are
displayed.
2 Press </M/m/, to select the character
you want to enter, and press ENTER.
The selected character appears at the top of
the display.
Example: Input Title Name
The type of characters will change according
to the language you select in Easy Setup.
Some languages allow you to enter an accent
mark.
To enter a letter with an accent mark, select an
accent followed by the letter.
Example: Select “ ` ” and then “a” to enter “à.”
To insert a space, select “Space.”
3 Repeat steps 1 and 2 to enter the
remaining characters.
To erase a character, move the cursor to the
right of the character at the input row. Select
“Back” and press ENTER.
To insert a character, move the cursor to the
right of the point where you want to insert the
character. Select the character and press
ENTER.
To erase all of the characters, select “Clear
All” and press ENTER.
4 Select “Finish,” and press ENTER.
To cancel the setting, select “Cancel.”
To use the number buttons
You can also use the number buttons to enter
characters.
1 In step 2 above, press a number button
repeatedly to select a character.
Example:
Press the number 3 button once to enter “D.”
Press the number 3 button three times to enter
“F.”
2 Press SET and select the next character.
3 Select “Finish” and press ENTER.
1 2 3
4 5 6
7 8 9
0
TOOLS
</M/m/,,
ENTER
Number
buttons, SET
K
"A"
"a"
Symbol
Cancel
Finish
Space
Clear All
Back
,. - 1
BA C 2
ED F 3
HG I 4
KJ L5
1
2
3
4
5
NM O 6
QP R S
UT V 8
XW Y Z
7
9
0
6
7
8
9
0
Input Title Name
Kids
"A"
"a"
Symbol
Space
Clear All
Back
,. - 1
BA C 2
ED F 3
HG I 4
KJ L5
1
2
3
4
5
NM O 6
QP R S
UT V 8
XW Y Z
7
9
0
6
7
8
9
0
Input Title Name
Cancel
Finish
Input row
41
Recording
Recording
Before Recording
Before you start recording…
This recorder can record on various discs. Select
the disc type according to your needs (page 8).
Check that the disc has enough available space
for the recording (page 35). For HDD,
DVD+RWs, and DVD-RWs, you can free up
disc space by erasing titles (page 65).
Adjust the recording picture quality and picture
size if necessary (page 49).
z Hint
Timer recordings will be made regardless whether or not
the recorder is turned on. You can turn off the recorder
without affecting the recording even after recording
starts.
Recording mode
Like the SP or LP recording mode of VCRs, this
recorder has six different recording modes.
Select a recording mode according to the time and
picture quality you need. For example, if picture
quality is your top priority, select the High Quality
mode (HQ). If recording time is your priority,
Super Long Play mode (SLP) can be a possible
choice. Note that recording times in the following
table are approximate and the actual times may
differ. Note also that the maximum continuous
recording time for a single title is eight hours
(HDD), or six hours (DVD). Contents beyond this
time will not be recorded.
Press REC MODE repeatedly to switch the
recording modes.
“HQ+” recording mode
“HQ+” records pictures in higher quality than HQ
on the HDD. Set “HQ Setting” in Features Setup
to “HQ+” (page 96). Maximum recording time is
34 hours for RDR-HX1000 or 21 hours for RDR-
HX900. “HQ” appears in the display.
Note
Situations below may cause slight inaccuracies with the
recording time.
– Recording a programme with poor reception, or a
programme or video source of low picture quality
– Recording on a disc that has already been edited
– Recording only a still picture or just sound
Recording stereo and bilingual
programmes
The recorder automatically receives and records
stereo and bilingual programmes based on the
ZWEITON system or the NICAM system.
The HDD and a DVD-RW (VR mode) can record
both main and sub sounds. You can switch
between main and sub when playing the disc. For
the HDD, you can select the sound track before
recording. Select “Main,” “Sub,” or “Main+Sub
in “HDD Bilingual Rec.” of Options Setup
(page 97).
A DVD+RW, DVD-RW (Video mode), DVD+R,
or DVD-R can record only one sound track (main
or sub) at a time. Select the sound track using the
Setup Display before recording starts. Set “DVD
Bilingual Rec.” to “Main” (default) or “Sub” in
Options Setup (page 97).
I want to record with the
best possible picture
quality, so I’ll select HQ.
Recording
mode
Recording time (hour)
HDD DVD
(HX1000) (HX900)
HQ
(High quality)
53 33 1
HSP R 81 51 1.5
SP
(Standard mode)
107 67 2
LP r 164 103 3
EP r 217 137 4
SLP
(Long duration)
325 204 6
,continued
42
ZWEITON (German stereo) system
When a stereo or bilingual ZWEITON based
programme is received, “STEREO” or
“BILINGUAL” appears in the front panel display.
NICAM system
When a stereo or bilingual NICAM based
programme is received, “NICAM” appears in the
front panel display.
To record a NICAM programme, be sure to set
“Audio” of “Channel Setting” in Settings Setup to
“NICAM” (default). If the sound is not clear when
listening to NICAM broadcasts, set “Audio” to
“Standard” (see “Channel Setting” on page 84).
z Hint
You can select the audio (main or sub) while recording
bilingual programmes using the (audio) button.
This does not affect the recorded sound.
Unrecordable pictures
Pictures with copy protection cannot be recorded
on this recorder.
When the recorder receives a copy guard signal,
the recorder continues to record but only a blank,
grey coloured screen will be recorded.
* The recorded disc can be played only on CPRM
compatible equipment (page 8).
Timer Recording (Standard/
VIDEO Plus+)
You can set the timer for a total of eight
programmes, up to one month in advance.
There are two methods to set the timer: the
standard method and VIDEO Plus+ method.
Standard: Set the date, time, and programme
position of the programme manually.
VIDEO Plus+: Enter the PlusCode number
designated for each TV programme (page 44).
Setting the timer manually
(Standard)
1 Press HDD or DVD.
If you select DVD, press Z (open/close) and
place a DVD on the disc tray. Press Z again
to close the disc tray.
Copy control
signals
Recordable discs
Copy-Free
Copy-Once
(Ver.1.1 with CPRM*)
Copy-Never None (a blank screen is
recorded)
+
RW
-
RW
VR
-
RW
Video
-
R
+
R
HDD
HDD
-
RW
VR
+
RW
-
RW
VR
-
RW
Video
-
R
+
R
HDD
1 2 3
4 5 6
7 8 9
0
</M/m/,,
ENTER
Z
[TIMER]
TOOLS
x REC
STOP
DVD
HDD
With the recording side facing down
43
Recording
Wait until “LOAD” disappears from the front
panel display.
Unused DVDs are formatted automatically.
2 Press [TIMER].
If the Timer programming (VIDEO Plus+)
menu appears, press < to switch the
display to “Standard.”
3 Select an item using </, and adjust
using M/m.
“Date”: Sets the date.
The item changes as follows:
Today y Tomorrow y …… y Thu
28.10 (1 month later) y Sun (every Sunday)
y …… y Sat (every Saturday) y
Mon-Fri (Monday to Friday) y Mon-Sat
(Monday to Saturday) y Sun-Sat (Sunday to
Saturday) y Today
“Start”: Sets the start time.
“Stop”: Sets the stop time.
“Prog.”: Selects the programme position or
input source.
“Media”: Selects the media, HDD or DVD.
“Mode”: Selects the recording mode
(page 41).
If you want to change the setting for the
PDC/VPS or Update functions, select
“Details” and press ENTER. Select an item
using </, and set using M/m.
“PDC/VPS”: Sets the PDC/VPS function. See
“About the PDC/VPS function” below.
“Update” (HDD only): Automatically records
over a previously recorded programme that is
set to be recorded daily or weekly.
To return to the Timer programming menu,
select “Previous” and ENTER.
If you make a mistake, select the item and
change the setting.
4 Select “OK,” and press ENTER.
The Timer List menu (page 46) appears. The
TIMER REC indicator lights up on the front
panel and the recorder is ready to start
recording.
Unlike a VCR, there is no need to turn off the
recorder before the timer recording starts.
To stop recording during timer recording
Open the remote’s cover and press x REC STOP.
Note that it may take a few seconds for the
recorder to stop recording.
About the PDC/VPS function
PDC/VPS signals are transmitted with TV
programmes in some broadcast systems. These
signals ensure that timer recordings are made
regardless of any broadcast delays, early starts, or
broadcast interruptions.
To use the PDC/VPS function
Set “PDC/VPS” to “On” in step 3 above.
When you turn on this function, the recorder starts
scanning the channel before the timer recording
starts. If you are watching TV when scanning
starts, a message will appear on the TV screen. If
you want to watch TV, switch to your TV’s tuner
or turn off the PDC/VPS channel scan function.
To turn off the PDC/VPS channel scan
Press TOOLS and select “PDC/VPS Scan Off.”
To ensure that the PDC/VPS function works
properly, turn off the recorder before the timer
recording starts. This will automatically turn on
the PDC/VPS channel scan function while the
recorder remains off.
Rec Mode Adjust
If there is not enough available disc space for the
recording, the recorder automatically adjusts the
recording mode to enable the entire programme to
be recorded. This function is normally set to “On.
To cancel this function, press TOOLS while the
Timer List is displayed. Select “Rec Mode
Adjust” and press ENTER. Select “Off” and press
ENTER.
Timer - Standard
Set the timer manually.
Cancel
OK
Date
VIDEO Plus+
To day
Start Prog.
Media Mode
Stop
::
Details
PDC/VPS: On Update: --
,continued
44
If the timer settings overlap
Overlapped timer settings are shown as follows.
To store the setting as shown, select “OK.” The
programme that starts first has priority and the
second programme starts recording only after the
first programme has finished.
To cancel the overlapped setting, select “Cancel.”
To confirm, change, or cancel timer recording
See “Checking/Changing/Cancelling Timer
Settings (Timer List)” (page 46).
To extend the recording duration time while
recording
1 Press TOOLS during recording.
The TOOLS menu appears.
2 Select “Extend Rec” and press ENTER.
3 Press M/m to select the duration time.
You can set the duration in increments of 10
minutes, for a maximum of 60 minutes.
4 Select “OK” and press ENTER.
One Touch Timer
If you use the SMARTLINK connection, you can
easily display the timer programming menu.
When the TV is turned on or in standby mode,
press [TIMER]. The recorder automatically turns
on and the TV’s input is switched to the recorder.
The Timer programming menu appears.
z Hint
You can play the recorded programme by selecting the
programme title in the Title List menu.
Notes
If “The disc is full or nearly full” appears on the screen,
change the disc, or make available space for the
recording (HDD/DVD+RW/DVD-RW only)
(page 66).
Check that the clock is correctly set before setting the
timer recording. If not, the timer recording cannot be
made.
To record a satellite programme, turn on the satellite
tuner and select the satellite programme you want to
record. Leave the satellite tuner turned on until the
recorder finishes recording. If you connect equipment
with a timer function, you can use the Synchro Rec
function (page 51).
Even if the timer is set for the same daily or weekly
programme, the timer recording cannot be made if it
overlaps with a programme that has priority. “ ” will
appear next to the overlapped setting in the Timer List.
Check the priority order of the settings.
Even if the timer is set, timer recordings cannot be
made while recording a programme that has priority.
The Rec Mode Adjust function only works with a timer
recording and the PDC/VPS function set to off. It does
not function with Quick Timer or Synchro Rec.
The beginning of some recordings may not be made
when using the PDC/VPS function.
You cannot extend the recording duration time when
“PDC/VPS” is set to “On.”
Recording TV programmes using the
VIDEO Plus+ system
The VIDEO Plus+ system is a feature that
simplifies setting the timer. Just enter the
PlusCode number listed in the TV programme
guide. The date, time, and channel of that
programme are set automatically.
Check that the channels are correctly set in
“Channel Setting” in Settings Setup (page 84).
Fri 29.10 21:00-22:00 AAB
DVD SP PDC/VPS
Fri 29.10 20:30-21:00 DEF
DVD SP PDC/VPS
Timer
These timer settings overlap. Do you want to continue?
OK
Cancel
Extend Rec. Time
Set the timer extend function.
Tue 28.9 10:00-11:30 AAB DVD SP
OK
Cancel
Extend Time
Off
45
Recording
1 Press HDD or DVD.
If you select DVD, insert a recordable DVD.
2 Press [TIMER].
If the Timer programming (Standard) menu
appears, press < to switch the display to
“VIDEO Plus+.”
3 Press the number buttons to enter the
PlusCode number, and press SET.
If you make a mistake, press CLEAR and re-
enter the correct number.
4 Select “OK,” and press ENTER.
The date, start and stop times, programme
position, recording mode, etc. setting
(page 43) appear.
If you want to change the setting, press </
, to select the item and press M/m to
change the setting. For the PDC/VPS or
Update functions, select “Details” and
change the settings (page 43).
To re-enter the PlusCode number, select
“Change.”
5 Select “OK,” and press ENTER.
The TIMER REC indicator lights up on the
front panel, and the recorder is ready to start
recording.
To stop recording during timer recording
Open the remote’s cover and press x REC STOP.
Note that it may take a few seconds for the
recorder to stop recording.
If the timer settings overlap
See page 44.
To extend the recording duration time while
recording
See page 44.
To confirm, change, or cancel timer recording
See “Checking/Changing/Cancelling Timer
Settings (Timer List)” (page 46).
z Hint
The Rec Mode Adjust function also works with this timer
method (page 43).
1 2 3
4 5 6
7 8 9
0
</M/m/,,
ENTER
[TIMER]
Number
buttons, SET
x REC
STOP
CLEAR
DVD
HDD
Timer - VIDEO Plus+
Set the timer by entering the timer code.
Standard
PlusCode No.
Cancel
OK
Timer - VIDEO Plus+
Is the following timer setting correct? To modify,
adjust each item or re-enter the timer code.
Date
Mon 28.6 10
Start Prog.
Media
OK
00
:11
Stop
30
:DVDSPAAB
Cancel
Details
Mode
Change
PDC/VPS: On Update: --
46
Checking/Changing/
Cancelling Timer Settings
(Timer List)
You can check, change, or cancel timer settings
using the Timer List menu.
1 Press SYSTEM MENU.
The System Menu appears.
2 Select “TIMER LIST,” and press ENTER.
Timer information displays the recording
date, time, recording mode, etc.
: Indicates that the setting is overlapped by
another setting.
(green): Indicates the setting can be
recorded
z
(red): Indicates the setting currently being
recorded.
a
(grey): Indicates that the setting cannot be
recorded in the selected recording mode.
: Indicates the setting being recorded on
the HDD.
: Indicates the setting being recorded on a
DVD.
: Indicates the setting that the Update
function is set for.
3 Select the timer setting you want to check/
change/cancel, and press ENTER.
The sub-menu appears.
4 Select one of the options, and press
ENTER.
“Modify”: Changes the timer setting.
Select an item using </, and adjust using
M/m. For the PDC/VPS or Update functions,
select “Details” and change the settings
(page 43). Select “OK” and press ENTER.
“Erase”: Erases the timer setting. Select “OK”
and press ENTER.
“Check Overlap”: Checks for overlapped
settings.
Select “Close” to return to the Timer List.
To change or cancel the setting, repeat steps 3
and 4 above.
-
RW
VR
-
RW
Video
+
RW
-
R
+
R
-
RW
Video
+
R
HDD
1 2 3
4 5 6
7 8 9
0
SYSTEM
MENU
</M/m/,,
ENTER
O RETURN
HDD
DVD
10:30
TIMER LIST
Mon-Sat 22:00-22:15
Fri 29.10 20:30-21:30
Fri 29.10 21:00-22:00
Sat 30.10 16:00-17:00
PDC
VPS
PDC
VPS
AAB
DEF
GHI
DEF
SP
SP
SLP
SLP
Modify
Modify the timer setting.
Cancel
Details
PDC/VPS: Off Update: On
Media
HDD
SP
Mode
OK
Date
Mon-Sat 22
Start Prog.
00
:22
Stop
15
: AAB
Erase
Are you sure you want to erase this timer setting?
Mon-Sat 22:00-22:15 AAB
Media: HDD Rec Mode: SP
OK Cancel
Check Overlap
These timer settings overlap.
Close
Fri 29.10 20:30-21:30 DEF
Fri 29.10 21:00-22:00 GHI
DVD SP
DVD SLP
PDC/VPS
PDC/VPS
47
Recording
When the timer settings overlap
The programme that starts first has priority and the
second programme starts recording only after the
first programme has finished.
When the recordings start at the same time
The programme that is set last has priority. In this
example, timer setting B is set after A, so the first
part of timer setting A will not be recorded.
When the end time of one recording and the
start time of another are the same
After finishing the previous recording, the other
recording may be delayed.
To turn off the Timer List
Press O RETURN.
z Hint
While recording, you cannot modify the timer setting for
the current recording, but you can extend the recording
duration of the recording time (page 44).
Notes
When “PDC/VPS” is set to “On” for one or more timer
recordings, the start times may change in the event of a
broadcast delay or early start.
Even if the timer is set, timer recordings cannot be
made while recording a programme that has priority.
Even if the timer is set for the same daily or weekly
programme, the timer recording cannot be made if it
overlaps with a programme that has priority. ” will
appear next to the overlapped setting in the Timer List.
Check the priority order of the settings.
Automatically erasing old titles
(Auto Title Erase)
If there is not enough space for a timer recording,
the recorder automatically erases old titles
recorded on the HDD. The oldest, played title is
erased. The protected titles are not erased.
1 Display the Timer List menu and press
TOOLS.
2 Select “Auto Title Erase,” and press
ENTER.
3 Select “On,” and press ENTER.
The default setting is “Off.”
7:00 8:00 9:00 10:00
A
B
will be cut off
7:00 8:00
A
B
9:00 10:00
7:00 9:00 10:00
A
B
HDD
48
Recording Without the
Timer
1 Press HDD or DVD to select a media.
When you selected DVD, insert a recordable
DVD.
2 Press PROG +/– to select the programme
position or input source you want to
record.
3 Press REC MODE repeatedly to select the
recording mode.
Each time you press the button, the display
changes on the TV screen as follows:
For more details about the recording mode,
see page 41.
4 Press z REC.
Recording starts.
Recording continues until you stop the
recording or the disc is full.
To stop recording
Press x REC STOP located beneath the remote
control cover. Note that it may take a few seconds
for recording to stop.
To pause recording
Press X REC PAUSE located beneath the remote
control cover. To restart recording, press the
button again.
To watch another TV programme while
recording
If your TV is connected to the LINE 1-TV jack, set
your TV to the TV input using the TV/DVD
button and select the programme you want to
watch. If your TV is connected to the LINE 2 OUT
or COMPONENT VIDEO OUT jacks, set the TV
to TV input using the
t (TV/video) button
(page 20).
TV Direct Rec
If you use the SMARTLINK connection, you can
easily record what you are watching on your TV.
When the TV is turned on or in standby mode,
press z REC. The recorder automatically turns on
and starts recording what you are watching on the
TV. “TV” appears in the front panel display. You
cannot turn off the TV or change the programme
position during TV Direct Rec. To turn off the
function, set “TV Direct Rec” to “Off” in Features
Setup (page 93).
About the Teletext function
Some broadcasts systems ensure a Teletext
service* in which the complete programmes and
their data (title, date, channel, recording start time
etc.) are stored day by day. When recording a
programme, the recorder automatically takes the
programme name from the Teletext pages and
stores it as the title name. For details, see “TV
Guide Page” (page 93).
Note that the Teletext information will not appear
on your TV screen. To view the Teletext
information on your TV screen, press TV/DVD on
the remote to switch the input source to your TV.
* not available in some areas
-
RW
VR
-
RW
VR
+
RW
-
R
+
R
-
RW
Video
+
R
HDD
1 2 3
4 5 6
7 8 9
0
z REC
REC MODE
x REC
STOP
X REC
PAUSE
</M/m/,,
ENTER
PROG +/–
t (TV/video),
TV/DVD
DVDHDD
HQ SP LP EPHSP SLP
49
Recording
z Hint
If you do not want to watch TV while recording, you can
turn off the TV. When using a decoder, make sure to
leave it on.
Notes
After pressing z REC, it may take a short while to start
recording.
You cannot change the recording mode while
recording or during recording pause.
If there is a power failure, the programme you are
recording may be erased.
You cannot watch a PAY-TV/Canal Plus programme
while recording another PAY-TV/Canal Plus
programme.
To use the TV Direct Rec function, you must first set
the recorder’s clock correctly.
Using the Quick Timer function
You can set the recorder to record in 30-minute
increments.
Press z REC repeatedly to set the duration.
Each press advances the time in 30-minute
increments. The maximum duration is six hours.
The time counter decreases minute by minute to
0:00, then the recorder stops recording (power
does not turn off). Even if you turn off the recorder
during recording, the recorder continues to record
until the time counter runs out.
Note that the Quick Timer function does not work
if “TV Direct Rec” is set to “On” in Features Setup
(page 93).
To cancel the Quick Timer
Press z REC repeatedly until the counter appears
in the front panel display. The recorder returns to
normal recording mode.
Adjusting the recording picture
quality and size
You can adjust the recording picture quality and
picture size.
1 Before recording starts, press TOOLS and
select “Rec Settings.” Then press ENTER.
2 Select the item you want to adjust, and
press ENTER.
The adjustment display appears.
Example: Rec NR
“Rec Mode”: Selects the recording mode for
the desired recording time and picture quality.
For more information, see “Recording mode”
(page 41).
0:30 1:00
5:30
6:00
(normal
recording)
1 2 3
4 5 6
7 8 9
0
</M/m/,,
ENTER
TOOLS
DISPLAY
Rec. Settings
Select the item you want to change.
Rec Mode :
HDD Rec. Picture Size :
DVD Rec. Picture Size :
Rec NR :
Rec Video Equalizer
SP
4 : 3
4 : 3
Off
Off 1 2 3
Rec NR
,continued
50
“HDD Rec. Picture Size”/“DVD Rec. Picture
Size”: Sets the picture size of the programme
to be recorded.
4:3 (default): Sets the picture size to 4:3.
16:9: Sets the picture size to 16:9 (wide
mode).
Auto (HDD only): Automatically selects the
actual picture size.
“DVD Rec. Picture Size” works with DVD-
Rs and DVD-RWs (Video mode) when the
recording mode is set to HQ, HSP, or SP. For
all other recording modes, the screen size is
fixed at “4:3.”
For DVD-RWs (VR mode), the actual picture
size is recorded regardless of the setting. For
example, if a 16:9 size picture is received, the
disc records the picture as 16:9 even if “DVD
Rec. Picture Size” is set to “4:3.
For DVD+RWs/DVD+Rs, the screen size is
fixed at “4:3.”
“Rec NR” (noise reduction): Reduces noise
contained in the video signal.
“Rec Video Equalizer”: Adjusts the picture in
greater detail.
Press M/m to select the item you want to
adjust, then press ENTER.
Contrast: Changes the contrast.
Brightness: Changes the overall brightness.
Colour: Makes the colours deeper or lighter.
3 Adjust the setting using </M/m/,,
and press ENTER.
The default setting is underlined.
“Rec NR”: (weak) Off
1 ~ 3 (strong)
“Rec Video Equalizer”:
Contrast: (weak) –3 ~ 0
~ 3 (strong)
Brightness: (dark) –3 ~ 0
~ 3 (bright)
Colour: (light) –3 ~ 0 ~ 3 (deep)
Repeat steps 2 and 3 to adjust any other items.
Notes
If one programme contains two picture sizes, the
selected size is recorded. However, if the 16:9 signal
cannot be recorded as 16:9, it is recorded as 4:3.
When playing a 16:9 size picture recorded as 4:3, The
image is fixed to 4:3 letter box regardless of the setting
in “TV Type” of Video Setup (page 88).
Remnants of images may appear on your screen when
using “Rec NR.”
“Rec Video Equalizer” does not affect the input of the
DV IN jack and does not work with RGB signals.
Checking the disc status while
recording
You can check the recording information such as
recording time or disc type.
Press DISPLAY twice during recording.
The recording information appears.
A Disc type/format
B Recording status
C Recording mode
D Recording time
Press DISPLAY to turn off the display.
Creating chapters in a title
The recorder will automatically divide a recording
(a title) into chapters by inserting chapter marks at
6 or 15-minute intervals during recording. Select
the interval, “6Min” (default) or “15Min” in
“Auto Chapter” of Features Setup (page 93).
z Hint
You can create chapters manually when playing the HDD
or DVD-RWs (VR mode). For details, see page 68.
1:23:45SP
DVD -RW
VIDEO
51
Recording
Recording From Connected
Equipment With a Timer
(Synchro Rec)
You can set the recorder to automatically record
programmes from connected equipment that has a
timer function (such as a satellite tuner). Connect
the equipment to the LINE 3/DECODER jack of
the recorder (page 28).
When the connected equipment turns on, the
recorder starts recording a programme from the
LINE 3/DECODER jack.
1 Before recording, select HDD or DVD. Set
“Synchro Rec” in Features Setup to
“Record to HDD” or “Record to DVD”
(page 96).
If you select DVD, insert a recordable DVD.
2 Press INPUT SELECT repeatedly to select
“L3.”
3 Select the line input audio when recording
a bilingual programme on the HDD or DVD-
RWs (VR mode).
Press TOOLS to display the TOOLS menu.
Select “Line Audio Input” and press ENTER.
Select “Bilingual” and press ENTER.
For details about bilingual recording, see
page 41.
4 Press REC MODE repeatedly to select the
recording mode, HQ, HSP, SP, LP, EP, or
SLP.
5 Set the timer on the connected equipment
to the time of the programme you want to
record, and turn it off.
6 Press SYNCHRO REC.
The SYNCHRO REC indicator lights up on
the front panel. The recorder is ready to start
Synchro-Recording.
The recorder automatically starts recording
when it receives an input signal from the
connected equipment. The recorder stops
recording when the connected equipment
turns off.
To stop recording
Press x REC STOP or SYNCHRO REC.
To cancel Synchro Rec
Press SYNCHRO REC. The SYNCHRO REC
indicator on the recorder turns off.
Notes
The recorder starts recording only after detecting the
video signal from the connected equipment. The
beginning of the programme may not be recorded
regardless of whether or not the recorder’s power is on
or off.
During Synchro-Recording, other operations such as
normal recording cannot be done.
To use the connected equipment while the recorder is
standing by for Synchro-Recording, cancel Synchro-
Recording by pressing SYNCHRO REC. Be sure to
turn off the connected equipment and press
SYNCHRO REC to reset Synchro-Recording before
the timer recording starts.
The Synchro Rec function does not work when “Line3
Input” of Video Setup is set to “Decoder” (page 90).
The Synchro Rec function does not work with some
tuners. For details, see the tuner’s operating
instructions.
While the recorder is standing by for Synchro-
Recording, the Auto Clock Set function (page 87) does
not work.
To use the Synchro Rec function, you must first set the
recorder’s clock correctly.
-
RW
VR
-
RW
VR
+
RW
-
R
+
R
-
RW
Video
+
R
HDD
REC MODE
</M/m/,,
ENTER
x REC STOP
SYNCHRO
REC
TOOLS
1 2 3
4 5 6
7 8 9
0
DVD
HDDHDD
,continued
52
If the timer settings of a Synchro-Recording
and another timer recording overlap
Regardless of whether or not the programme is a
Synchro Rec programme, the programme that
starts first has priority and the second programme
starts recording only after the first programme has
finished.
Recording From Connected
Equipment Without a Timer
You can record from a connected VCR or similar
device. To connect a VCR or similar device, see
“Connecting a VCR or Similar Device” (page 26).
Use the DV IN jack on the front panel if the
equipment has a DV output jack (i.LINK jack).
1 Press HDD or DVD.
If you select DVD, insert a recordable DVD.
2 Press INPUT SELECT to select an input
source according to the connection you
made.
The front panel display changes as follows:
7:00 8:00 9:00 10:00
First programme
Second programme
will be cut off
-
RW
VR
-
RW
VR
+
RW
-
R
+
R
-
RW
Video
+
R
HDD
1 2 3
4 5 6
7 8 9
0
TOOLS
M/m, ENTER
X REC
PAUSE
x REC
STOP
REC MODE
INPUT
SELECT
DVD
HDD
L2L1 L4L3 DV
programme
position
53
Recording
3 Select the line input audio when recording
a bilingual programme on the HDD or DVD-
RWs (VR mode).
Press TOOLS to display the TOOLS menu.
Select “Line Audio Input” and press ENTER.
Select “Bilingual” and press ENTER.
For details about bilingual recording, see
page 41.
4 Press REC MODE repeatedly to select the
recording mode, HQ, HSP, SP, LP, EP, or
SLP.
5 Press X REC PAUSE to set this recorder to
record pause.
6 Insert the source tape into the connected
equipment and set to playback pause.
7 At the same time, press X REC PAUSE on
this recorder and the pause or play button
on the connected equipment.
Recording starts.
To stop recording, press x REC STOP on this
recorder.
If you connect a digital video camera with a DV
IN jack
See “DV Dubbing (DV t HDD/DVD)”
(page 77) for an explanation of how to record from
the DV IN jack.
z Hint
You can adjust the settings for the recording picture
before recording. See “Adjusting the recording picture
quality and size” (page 49).
Notes
When recording a video game image, the screen may
not be clear.
Any programme that contains a Copy-Never copy
guard signal cannot be recorded. The recorder
continues to record, but a blank screen will be recorded.
54
Playback
Playing
1 Press HDD or DVD.
If you select DVD, press Z (open/close) and
place a DVD or CD on the disc tray. Then
press the button again to close the disc tray.
If you insert a DVD VIDEO, VIDEO CD,
CD, or DATA CD, press H. Playback
starts.
2 Press TITLE LIST.
For details about the Title List, see “Using the
Title List” (page 33).
Example: DVD-RW (VR mode)
3 Select the title, and press ENTER.
The sub-menu appears.
4 Select “Play,” and press ENTER.
Playback starts from the selected title.
To use the DVD’s Menu
When you play a DVD VIDEO, or a finalized
DVD+RW, DVD-RW (Video mode), DVD+R, or
DVD-R, you can display the disc’s menu by
pressing TOP MENU or MENU.
To play VIDEO CDs with PBC functions
PBC (Playback Control) allows you to play
VIDEO CDs interactively using the menu on your
TV screen.
When you start playing a VIDEO CD with PBC
functions, the menu appears.
Select an item using the number buttons and press
ENTER. Then, follow the instructions in the menu
(press
H when “Press SELECT” appears).
The PBC function of Super VCDs does not work
with this recorder. Super VCDs are played in
continuous play mode only.
To stop playback
Press x.
To resume playback from the point where you
stopped (Resume Play)
When you press H again after you stop
playback, the recorder resumes playback from the
point where you pressed
x.
To start from the beginning, press TOOLS, select
“Play Beginning” and press ENTER. Playback
starts from the beginning of the title/track/scene.
The point where you stopped playing is cleared
when:
you open the disc tray (except for HDD).
you play another title (except for HDD).
you switch the Title List menu to Original or
Playlist (DVD-RW in VR mode only).
+
R
DVD
VCD
CD
DATA CD
-
RW
VR
-
RW
Video
+
RW
-
R
HDD
1 2 3
4 5 6
7 8 9
0
TITLE LIST
</M/m/,,
ENTER
TOOLS
H
TOP MENU
x
MENU
X
"/1
Z
Number
buttons, SET
O RETURN
DVD
HDD
With the playback side facing down
1 AAB 13:00-14:00
2 DEF 20:00-21:00
3 AAB 9:00- 9:30
4 GHI 20:00-20:30
5 DEF 20:00-20:30
6 L3 21:00-21:30
7 L3 21:00-21:30
8 GHI 10:00-10:30
15. 9
17. 9
25. 9
25. 9
15.10
19.10
26.10
28.10
Wed
Fri
Sat
Sat
Fri
Tu e
Tu e
Thu
Sort
1.5/4.7GB
My Movies
TITLE LIST
ORIGINAL
Date
Title
Number
55
Playback
you edit the title after stopping playback.
you change the settings on the recorder.
you turn off the recorder (VIDEO CD/CD/
DATA CD only).
you make a recording (except for HDD/DVD-
RWs in VR mode).
To play restricted DVDs (Parental Control)
If you play a restricted DVD, the message “Do
you want temporarily change parental control to
*?” appears on your TV screen.
1 Select “OK” and press ENTER.
The display for entering your password
appears.
2 Enter your four-digit password using the
number buttons.
3 Press ENTER to select “OK.”
The recorder starts playback.
To register or change the password, see “Parental
Control (DVD VIDEO only)” (page 94).
To lock the disc tray (Child Lock)
You can lock the disc tray to prevent children from
ejecting the disc.
When the recorder is in standby mode, press
O RETURN, ENTER, and then {/1 on the
remote.
“LOCKED” appears on the front panel display.
The Z (open/close) button does not work while
the Child Lock is set.
To unlock the disc tray, press O RETURN,
ENTER, and then {/1 on the remote again when
the recorder is in standby mode.
One Touch Play
If you use the SMARTLINK connection, you can
easily start playing.
When the TV is turned on or in standby mode,
press H. The recorder automatically turns on and
the TV’s input is switched to the recorder.
Playback starts automatically.
One Touch Menu
If you use the SMARTLINK connection, you can
easily display the Title List.
When the TV is turned on or in standby mode,
press TITLE LIST. The recorder automatically
turns on and the TV’s input is switched to the
recorder. The Title List menu appears.
z Hints
You can also use the H button in step 3 (page 54) to
start playback.
Even if a timer recording starts during playback,
neither the recording nor playback will stop (page 60).
Even if you select “Factory Setup” in Options Setup
(page 97), the Child Lock remains set.
,continued
56
Playback options
Buttons Operations Discs
Z (open/close) Stops play and opens the disc tray. All discs
(audio) Selects one of the audio tracks recorded on the disc
when pressed repeatedly.
: Selects the language.
: Selects the main or sub sound.
: Selects stereo or monaural
audio tracks.
(subtitle) Selects a subtitle language when pressed repeatedly.
(angle) Selects an angle when pressed repeatedly.
If various angles (multi-angles) for a scene are
recorded on the disc, “ appears in the front panel
display.
1 2 3
4 5 6
7 8 9
0
Z
X
m / M
./>
/
H
SUR
PROGRESSIVE
DVD
-
RW
VR
HDD
CD
DATA CD
VCD
-
RW
VR
DVD
VCD
CD
DATA CD
HDD
DVD
DVD
57
Playback
To resume normal playback, press H.
SUR (surround) Selects one of the TVS effects when pressed
repeatedly.
TVS* (TV Virtual Surround) lets you enjoy virtual
surround sound effects created from the front left and
right speakers. The selected setting is displayed in the
front panel display for a few seconds.
“TVS OFF”: No surround effect
“TVS DYNAMIC”: Creates one set of virtual rear
speakers.
“TVS WIDE”: Creates five sets of virtual rear
speakers.
“TVS NIGHT”: Creates five sets of virtual rear
speakers. Effective at low volume.
“TVS STANDARD”: Creates three sets of virtual rear
speakers. Effective when you use two separate front
speakers.
* TVS was developed
by Sony to produce
home surround sound
with just a stereo TV.
This works with
multichannel Dolby
Digital and MPEG
soundtracks.
PROGRESSIVE Switches the type of video output signal to interlace or
progressive format (page 16).
/ (instant
replay/instant
advance)
Replays the scene/briefly fast forwards the scene.
. (previous)/
> (next)
Goes to the beginning of the previous/next title/
chapter/scene/track.
All discs
(fast reverse/fast
forward)
Fast reverses/fast forwards the disc when pressed
during playback.
Search speed changes as follows:
fast reverse fast forward
FR1 T t FF1
FR2 T T t t FF2
FR3* T T T t t t FF3*
When you press and hold the button, fast forward/fast
reverse continues at the selected speed until you
release the button.
All discs
* FR3 and FF3 are only
available for the HDD
and DVDs.
(slow, freeze frame)
Plays in slow motion when pressed for more than one
second in pause mode.
Plays one frame at a time when pressed briefly in
pause mode.
* Playback direction
only
X (pause) Pauses playback. All discs
Buttons Operations Discs
DVD
-
RW
VR
-
RW
Video
+
RW
-
R
+
R
VCD
DVD
+
RW
HDD
-
RW
VR
-
RW
Video
HDD
-
R
+
R
DVD
+
RW
-
RW
VR
-
RW
Video
+
RW
-
R
+
R
VCD
DVD
*
+
RW
HDD
,continued
58
Notes
To enjoy the TVS function, set “Digital Output” to
“On” and “Dolby Digital” to “D-PCM” in Audio
Setup.
When the playback signal does not contain a signal for
the rear speakers, the surround effects will be difficult
to hear.
When you select one of the surround modes, turn off
the surround settings of the connected TV or amplifier
(receiver).
Make sure that your listening position is between and
at an equal distance from your speakers, and that the
speakers are located in similar surroundings.
The TVS function cannot be used with titles recorded
on this recorder. Angles and subtitles also cannot be
changed.
When you use the DIGITAL OUT (COAXIAL) jack to
listen to MPEG audio signals and set “MPEG” to
“MPEG” in Audio Setup, no sound will come from
your speakers if you select one of the TVS modes.
Notes on playing DTS sound tracks on a CD
When playing DTS-encoded CDs, excessive noise will
be heard from the analogue stereo jacks. To avoid
possible damage to the audio system, the consumer
should take proper precautions when the analogue
stereo jacks of the recorder are connected to an
amplification system. To enjoy DTS Digital
Surround™ playback, an external 5.1-channel decoder
system must be connected to the digital jack of the
recorder.
Set the sound to “Stereo” using the (audio)
button when you play DTS sound tracks on a CD
(page 56).
Notes on playing DVDs with a DTS sound track
DTS audio signals are output only through the DIGITAL
OUT (COAXIAL or OPTICAL) jack.
When you play a DVD with DTS sound tracks, set
“DTS” to “On” in Audio Setup (page 92).
Adjusting the picture quality
1 Press TOOLS during playback.
The TOOLS menu appears.
2 Select “Video Settings,” and press
ENTER.
3 Select an item, and press ENTER.
The adjustment display appears.
“Y NR” (luminance noise reduction):
Reduces noise contained in the luminance
element of the video signal.
“C NR” (chroma noise reduction): Reduces
noise contained in the colour element of the
video signal.
“BNR” (block noise reduction): Reduces
“block noise” or mosaic like patterns in the
picture.
“DVE” (digital video enhancer): Sharpens the
outlines of the images.
“PB Video Equalizer” (Playback video
equalizer): Adjusts the picture in greater
detail.
Select an item and press ENTER.
Contrast: changes the contrast.
Brightness: changes the overall brightness.
Colour: makes the colours deeper or lighter.
Hue: changes the colour balance.
+
R
DVD
VCD
-
RW
VR
-
RW
Video
+
RW
-
R
HDD
Video Settings
Select the item you want to change.
Y NR :
C NR :
BNR :
DVE :
PB Video Equalizer
2
2
2
Off
59
Playback
4 Press </, to adjust the setting, and
press ENTER.
The default settings are underlined.
Y NR: (weak) Off 1 2 3 (strong)
C NR: (weak) Off 1 2 3 (strong)
BNR: (weak) Off 1 2 3 (strong)
DVE*: (weak) Off 1 2 3 (strong)
PB Video Equalizer”:
Contrast: (weak) –3 ~ 0 ~ 3 (strong)
Brightness: (dark) –3 ~ 0
~ 3 (bright)
Colour: (light) –3 ~ 0 ~ 3 (deep)
Hue: (red) –3 ~ 0
~ 3 (green)
Repeat steps 3 and 4 to adjust any other items.
* “1” softens the outlines of the images. “2”
enhances the outlines and “3” enhances them more
than “2.”
Notes
If the outlines of the images on your screen become
blurred, set “BNR” to “Off.”
Depending on the disc or the scene being played, the
above BNR, Y NR, or C NR effects may be hard to
discern. And, these functions may not work with some
screen sizes.
When playing a title recorded in SLP recording mode,
the BNR setting may have little effect.
When using the DVE function, noise found in the title
may become more apparent. In this case, it is
recommended that you use the BNR function with the
DVE function. If the condition still does not improve,
set the DVE level to “1” or “Off.”
Adjusting the sound quality
1 Press TOOLS during playback.
The TOOLS menu appears.
2 Select “Audio Settings,” and press
ENTER.
3 Select an item, and press ENTER.
“Surround (TVS)” (DVD VIDEO only):
Selects one of the surround modes. For more
information, see “Playback options”
(page 56).
“Audio Filter” (all discs): Selects the digital
filter to reduce noise above 22.05 kHz (Fs* is
44.1 kHz), 24 kHz (Fs is 48 kHz), or 48 kHz
(Fs is above 96 kHz).
Sharp (default): Provides a wide frequency
range and spatial feeling.
Slow: Provides smooth and warm sound.
* Sampling frequency of audio source. This
function only adjusts the output signals from the
LINE 1 – TV, LINE 3/DECODER, or LINE 2
OUT (AUDIO L/R).
4 Press </M/m/, to select the option,
and press ENTER.
Note
There may be little effect by changing the Audio Filter
depending on the disc or playback environment.
+
R
DVD
VCD
-
RW
VR
-
RW
Video
+
RW
-
R
HDD
CD
60
Chasing Playback/
Simultaneous Rec and Play
You can view the beginning of a programme while
it is being recorded. You can also play a title or
previously recorded programme while recording.
Playing from the beginning of the
programme you are recording
(Chasing Playback)
“Chasing Playback” allows you to view the
recorded part of a programme while the recording
is being made. You do not need to wait until the
recording finishes.
1 Press TOOLS while recording.
The TOOLS menu appears.
2 Select “Chasing Playback,” and press
ENTER.
Playback starts from the beginning of the
programme you are recording.
When you fast forward to the point that you
are recording, Chasing Playback returns to
normal playback.
Notes
For DVD-RWs (VR mode), this function does not
work when recording:
– on a 1x-speed DVD-RW.
– in the HQ or HSP recording mode.
The DVD’s picture on your TV screen freezes for a few
seconds when you fast forward/fast reverse or instant
replay/advance the recording.
Playing a previous recording while
making another (Simultaneous Rec
and Play)
“Simultaneous Rec and Play” allows you to view
a previously recorded programme while recording
programmes. Playback continues even if a timer
recording starts. Use this function as follows:
While recording to the HDD:
Play another title on the HDD.
Play a previously recorded programme on a
DVD by pressing DVD.
While recording to a DVD:
Play a previously recorded programme on the
HDD by pressing HDD.
While recording to a DVD-RW (VR mode)*
1
:
Play another title on the same DVD-RW (VR
mode) disc.*
2
*
1
Simultaneous Rec and Play function does not work
when you record:
– on a 1x-speed DVD-RW.
– in the HQ or HSP recording mode.
*
2
Picture noise may appear depending upon the
condition of the recording, or when playing a title
recorded in the HQ or HSP recording mode.
You can also play a DVD VIDEO, VIDEO CD,
Super VCD, CD, or DATA CD while recording on
the HDD.
Example: Play another title on the HDD while
recording to the HDD.
1 While recording, press TITLE LIST to
display the HDD Title List.
2 Select the title you want to play, and press
ENTER.
3 Select “Play” from the sub-menu, and press
ENTER.
Playback starts from the selected title.
Example: Play a DVD while recording to the
HDD.
1 While recording, press DVD and insert the
DVD into the recorder.
2 Press TITLE LIST to display the DVD Title
List.
1 2 3
4 5 6
7 8 9
0
TOOLS
M/m,
ENTER
TITLE LIST
DVD
HDD
HDD
-
RW
VR
+
R
DVD
-
RW
VR
-
RW
Video
+
RW
-
R
HDD
VCD CD
DATA CD
61
Playback
3 Select the title you want to play, and press
ENTER.
4 Select “Play” from the sub-menu, and press
ENTER.
Playback starts from the selected title.
Notes
The DVD’s playback picture on your TV screen
freezes for a few seconds when you fast forward/fast
reverse or instant replay/advance during Simultaneous
Rec and Play.
You cannot play a DVD recorded in NTSC colour
system while recording on the HDD.
Searching for a Title/
Chapter/Track, etc.
You can search a disc by title, chapter, scene or
track. As titles and tracks are assigned individual
numbers, select the title or track by entering its
number. You can also search for a scene using the
time code.
1 Press TOOLS during playback.
The TOOLS menu appears.
2 Select a search method, and press ENTER.
“Title Search” (for DVDs)
“Chapter Search” (for HDD/DVDs)
“Track Search” (for CDs/DATA CDs)
“Search” (for VIDEO CDs)
“Album Search” (for DATA CDs)
“Time Search” (for HDD/DVDs): Searches
for a starting point by entering the time code.
The display for entering the number appears.
Example: Title Search
The number in parentheses indicates the total
number of titles, tracks, etc.
+
R
DVD
VCD
CD
DATA CD
-
RW
VR
-
RW
Video
+
RW
-
R
HDD
1 2 3
4 5 6
7 8 9
0
TOOLS
M/m,
ENTER
Number
buttons,
SET
Title : -- (21)
,continued
62
3 Press the number buttons to select the
number of the title, chapter, track, time
code, etc., you want.
For example: Time Search
To find a scene at 2 hours, 10 minutes, and 20
seconds, enter “21020.”
If you make a mistake, press CLEAR to
cancel the number, then select another
number.
4 Press SET.
The recorder starts playback from the selected
number.
Note
“Title Search” is not applicable to the HDD.
Playing MP3 Audio Tracks
You can play MP3 audio tracks on DATA CDs
(CD-ROMs/CD-Rs/CD-RWs).
1 Insert a DATA CD on the disc tray.
2 Press H.
Playback starts from the first MP3 audio
tracks on the disc. Note that the playback
order may be different from the edited order.
See “Playback order of MP3 audio tracks”
below.
About MP3 audio tracks
MP3 is audio compression technology that
satisfies certain ISO/MPEG regulations.
You can play back DATA CDs (CD-ROMs/CD-
Rs/CD-RWs) recorded in MP3 (MPEG1 Audio
Layer 3) format. However, the discs must be
recorded according to ISO9660 Level 1, Level 2
or Joliet format for the recorder to recognize the
tracks. You can also play discs recorded in Multi
Session.
See the instructions supplied with the CD-R/CD-
RW drives and the recording software (not
supplied) for details on the recording format.
Note on Multi Session discs
If MP3 audio tracks are recorded in the first
session, the recorder will also play MP3 audio
tracks in other sessions. If audio tracks in Music
CD format are recorded in the first session, only
the first session will be played back.
DATA CD
1 2 3
4 5 6
7 8 9
0
H
63
Playback
Playback order of MP3 audio tracks
Albums containing MP3 audio tracks play in the
following order.
A t B t C t D t F t G. Albums that
do not contain tracks (such as album E) are
skipped.
When you insert a DATA CD and press
H, the numbered tracks are played sequentially,
from 1 through 7. Any sub-albums/tracks
contained within a currently selected album take
priority over the next album in the same tree.
(Example: C contains D so 4 is played before
5.)
z Hints
You can view the disc information while playing MP3
audio tracks (page 39).
If you add numbers (01, 02, 03, etc.) to the front of the
track names when you store the tracks in a disc, the
tracks will be played in that order.
Since a disc with many trees takes longer to start
playback, it is recommended that you create albums
with no more than two trees.
Notes
Depending on the software you use to create the DATA
CD, the playback order may differ from the above
illustration.
Proceeding to the next or another album may take some
time.
The recorder may not be able to play some DATA CDs
created in the Packet Write format.
The recorder will play any data with the extension
“.MP3,” even if they are not in MP3 format. Playing
this data may generate a loud noise which could
damage your speaker system.
The recorder does not conform to audio tracks in
MP3PRO format.
The playback order above may not be applicable if
there are more than a total of 999 albums and tracks in
the DATA CD.
The recorder can recognize up to 499 albums (the
recorder will count just albums, including albums that
do not contain MP3 audio tracks). The recorder will not
play any albums beyond the first 499 albums. Of the
first 499 albums, the recorder will play no more than a
combined total of 999 albums and tracks.
The recorder can play MP3 audio tracks recorded in the
following sampling frequencies: 32 kHz, 44.1 kHz,
48 kHz.
Only the letters in the alphabet and numbers can be
used for album or track names. Anything else is
displayed as “
*
.”
ID3 tags cannot be displayed.
ROOT
Tree 1 Tree 2 Tree 3 Tree 4 Tree 5
Album
MP3 audio track
64
Editing
Before Editing
This recorder offers various edit options for
various disc types. Before you edit, check the disc
type in the front panel display, and select the
option available for your disc (page 8).
Note
You may lose the edited contents if you remove the disc
or a timer recording starts while editing.
Edit options for the HDD and
DVD+RWs/DVD-RWs (Video mode)/
DVD+Rs/DVD-Rs
You can perform simple edits. Since Video mode
titles are actual recordings on the disc, you cannot
undo any edits you make. The edit functions
available for Video mode titles are:
Setting protection against erasure (page 65).
Labelling a title (page 65).
Erasing a title (page 65).
Erasing multiple titles (page 66).
Erasing a section of a title (A-B Erase) (HDD
and DVD+RWs only) (page 66).
Erasing titles to open up disc space (Disc Map)
(DVD+RWs and DVD-RWs (Video mode)
only) (page 67).
Notes
Once the DVD is finalized, you cannot edit or record on
the disc (except for DVD+RWs and DVD-RWs (VR
mode)).
You cannot create a Playlist (see below).
If a message appears and indicates that the disc’s
control information is full, erase unnecessary titles.
Edit options for DVD-RWs (VR mode)
You can enjoy advanced edit functions. First you
have two options for a DVD-RW (VR mode):
editing either the original recording (called the
“original”), or the playback information created
from the original (called a “Playlist”). Since each
is different in nature and offers different merits,
read the following and select the one that better
suits your needs.
To edit original titles
Edits made to the original titles are final. If you
plan to retain an unaltered original recording,
create and edit a Playlist (see below). The edit
functions available for original titles are:
Labelling a title (page 65).
Setting protection against erasure (page 65).
Erasing a title (page 65).
Erasing multiple titles (page 66).
– Erasing a section of a title (A-B Erase) (page 66).
To create and edit Playlist titles
A Playlist is a group of Playlist titles created from
the original title for editing purposes. When you
create a Playlist, only the control information
necessary for playback, such as the playback
order, is stored on the disc. Since the original titles
are left unaltered, Playlist titles can be re-edited.
Example: You have recorded the final few
matches of a football tournament on a DVD-RW
(VR mode). You want to create a digest with the
goal scenes and other highlights, but you also want
to keep the original recording.
In this case, you can compile highlight scenes as a
Playlist title. You can even rearrange the scene
order within the Playlist title (“Creating and
Editing a Playlist” on page 68).
-
RW
Video
+
RW
-
R
+
R
HDD
-
RW
VR
65
Editing
The advanced edit functions available for Playlist
titles are:
Labelling a title (page 65).
Erasing a title (page 65).
Erasing multiple titles (page 66).
– Erasing a section of a title (A-B Erase) (page 66).
Rearranging the title order (page 70).
Dividing a title into multiple titles (page 70).
Combining multiple titles into one title
(page 71).
z Hint
You can display the disc’s Playlist titles in the Title List
(Playlist), or the original titles in the Title List (Original).
To switch the two Title Lists, press TOOLS while a Title
List is displayed, and select “Original” or “Playlist.”
Notes
The Playlist title calls up data from the original titles for
playback. When an original title is used for a Playlist
title, the original title cannot be erased.
You cannot protect Playlist titles.
If a message appears and indicates that the disc’s
control information is full, erase unnecessary titles.
Editing a Title
This section explains the basic edit functions. Note
that editing is irreversible. To edit a DVD-RW
(VR mode) without changing the original
recordings, create a Playlist title (page 68).
Note
When editing a DVD+R, DVD-R, or DVD-RW (Video
mode), finish all editing before finalizing the disc. You
cannot edit a finalized disc.
1 Press TITLE LIST.
When editing a DVD-RW in VR mode, press
TOOLS and select “Original” or “Playlist”
from the TOOLS menu to switch the Title
Lists, if necessary.
2 Select a title, and press ENTER.
The sub-menu appears.
3 Select an option, and press ENTER.
You can make the following edits to the title.
“Erase”: Erases the selected title. Select “OK”
when asked for confirmation. When the title is
protected, the display asks for confirmation.
To erase, select “Change,” and when the
Protection display appears, select “Off.”
-
RW
VR
-
RW
Video
+
RW
-
R
+
R
HDD
1 2 3
4 5 6
7 8 9
0
</M/m/,,
ENTER
TOOLS
TITLE LIST
m/M
CHAPTER
ERASE
CHAPTER
MARK
,continued
66
“Protect”: Protects the title. Select “On” when
the Protection display appears. ” appears
next to the protected title. To cancel the
protection, select “Off.”
“Title Name”: Allows you to enter or re-enter
a title name (page 40).
“Set Thumbnail”: Changes the title’s
thumbnail picture that appears in the Title List
(page 33).
“A-B Erase”: Erases a section of the title (see
below).
z Hints
You can erase multiple titles at one time (page 66), or
erase all of the titles on the disc at once (page 36).
You can label or re-label DVDs (page 36).
Note
You cannot protect Playlist titles.
Erasing a section of a title
(A-B Erase)
You can select a section (scene) in a title and erase
it. Note that erasing scenes in a title cannot be
undone.
1 After step 2 of “Editing a Title,” select
“A-B Erase” and press ENTER.
The display for setting point A appears.
When the title is protected, the display asks
for confirmation. To continue, select
“Change,” and when the protection display
appears, select “Off.”
2 Select point A by pressing m/M, and
press ENTER.
The display for setting point B appears.
3 Select point B by pressing m/M, and
press ENTER.
The display asks for confirmation. To reset
either point A or B, select “Change A” or
“Change B,” and go to step 2 or 3.
4 Select “OK,” and press ENTER.
The scene is erased, and the display asks
whether to erase another scene. To continue,
select “Yes,” and repeat from step 2. To finish,
select “No.”
z Hint
A chapter mark is inserted after the scene was erased. The
chapter mark divides the title into separate chapters on
either side of the mark.
Notes
Images or sound may be momentarily interrupted at the
point where you erase a section of a title.
Sections shorter than five seconds may not be erased.
For DVD+RWs, the erased section may be slightly
different from the points you selected.
Erasing multiple titles (Erase Titles)
You can select and erase more than one title at one
time using the TOOLS menu.
1 Press TITLE LIST to turn on the Title List
menu, and press TOOLS.
The TOOLS menu appears.
2 Select “Erase Titles,” and press ENTER.
The display for selecting titles to be erased
appears.
+
RW
-
RW
VR
HDD
A-B Erase (Set point A) 2 DEF 20:00-21:00
A 0:12:34
B : :
– – – –
Playback point
A-B Erase (Set point B)
A 0:12:34
B 0:23:45
A
2 DEF 20:00-21:00
-
RW
VR
-
RW
Video
+
RW
-
R
+
R
HDD
67
Editing
3 Select a title, and press ENTER.
A check mark appears in the check box next to
the selected title. To clear the check mark,
press ENTER again. To clear all of check
marks, select “Reset All.
When the title is protected, the display asks
for confirmation. To continue, select
“Change,” and when the protection display
appears, select “Off.” To cancel, select
“Close.”
4 Repeat step 3 to select all of the titles you
want to erase.
5 When you finish selecting titles, select
“OK,” and press ENTER.
The list of the titles to be erased appears for
confirmation. To change the selection, select
“Change,” and repeat from step 3.
6 Select “OK” and press ENTER.
The titles are erased.
Erasing titles to open up disc space
(Disc Map)
When recording on a DVD+RW or DVD-RW
(Video mode), the recorder searches for the largest
open space and records there. Before you start,
check the disc status by using Disc Map, and erase
titles to create a space large enough for the
recording.
1 Insert a disc and press TITLE LIST.
2 Press TOOLS and select “Disc Map,” and
press ENTER.
The Disc Map appears. To check the open
space, select the space by pressing </,.
When b or B appears on either side of the
screen, you can scroll sideways by pressing
</,.
3 Select a title by pressing </,, and
press ENTER.
The display for selecting titles to be erased
appears. To cancel the selection, press
ENTER again.
When the title is protected, the display asks
for confirmation. To continue, select
“Change,” and when the protection display
appears, select “Off.” To cancel, select
“Close.”
4 Repeat step 3 when erasing more titles.
5 Select “Erase,” and press ENTER.
The display asks for confirmation. To change
the selection, select “Change.”
6 Select “OK,” and press ENTER.
The selected titles are erased, freeing up disc
space.
1 AAB 13:00-14:00 15. 9
2 DEF 20:00-21:00 17. 9
3 AAB 9:00- 9:30 25. 9
4 GHI 20:00-20:30 25. 9
5 DEF 20:00-20:30 15.10
Erase Titles
Select the titles to erase.
OK
Cancel
Reset All
-
RW
Video
+
RW
Disc Map
Empty Title
Erase
Cancel
2.3GB
HQ: 0H30M
LP : 1H30M
HSP: 0H45M
EP: 2H00M
SP: 1H00M
SLP: 3H00M
Selected open space
Disc Map
Erase Cancel
2 DEF 20:00- 21:00
Fri 17.9 20:00( 1H00M) SP 0.6GB
Selected title
,continued
68
Creating chapters manually
You can manually insert a chapter mark at any
point you like during playback or recording.
Press CHAPTER MARK at the point where you
want to divide the title into chapters.
Each time you press the button, “Marking...”
appears on the screen and the scenes to the left and
right of the mark become separate chapters.
To erase chapter marks
You can combine two chapters by erasing the
chapter mark during playback.
Press
./> to search for a chapter number, and
while displaying the chapter containing the
chapter mark you want to erase, press CHAPTER
ERASE.
The current chapter combines with the previous
chapter.
Notes
If a message appears and indicates that no more chapter
marks can be added, you may not be able to record or
edit.
When dubbing, any chapter marks you enter will be
erased.
Creating and Editing a
Playlist
Playlist edit allows you to edit or re-edit without
changing the actual recordings. A Playlist title can
contain up to 50 scenes.
For details, see “Edit options for DVD-RWs (VR
mode)” (page 64).
Note
Once you create a Playlist title from original titles, you
will be unable to erase or edit the original titles.
1 Press TITLE LIST to turn on the Title List
menu, and press TOOLS.
The TOOLS menu appears.
2 Select “Create Playlist,” and press ENTER.
The display for selecting titles appears.
-
RW
VR
HDD
Marking...
-
RW
VR
1 2 3
4 5 6
7 8 9
0
</M/m/,,
ENTER
TOOLS
H
TITLE LIST
m/M
69
Editing
3 Select the title you want to include in the
Playlist title, and press ENTER.
A check mark appears in the check box next to
the selected title. To clear the check mark,
press ENTER again. To select all of the titles,
select “Select All.”
4 Repeat step 3 to add more titles.
To go to the next page of titles, press m. To
clear all of the check marks, select “Reset
All.”
5 Select “OK,” and press ENTER.
The list of selected titles appears. To add
another title, select “Add Title.
6 Select one of the titles, and press ENTER.
The sub-menu appears.
“Capture”: Adds a section of the title to the
Playlist title as one scene.
“Capture All”: Adds the entire title to the
Playlist title as one scene. After capturing the
title, select “Scene List” and go to step 12.
“Check Scenes”: Allows you to check the
captured scene.
7 Select “Capture,” and press ENTER.
The display for setting the start point (IN)
appears. The title starts to play in the
background.
8 Select the IN point by pressing m/M,
and press ENTER.
The display for setting the end point (OUT)
appears, and the title continues to play in the
background.
9 Select the OUT point by pressing m/M,
and press ENTER.
The display asks for confirmation. To reset the
IN or OUT point, select “Change IN” or
“Change OUT” and repeat step 8 or 9. To view
the selected scene, select “Preview.”
10Select “OK,” and ENTER.
The selected section is captured as a scene,
and the display asks whether you want to
continue. To continue, select “More,” and
repeat the steps above. To capture a scene
from another title, select “New Title.”
11When you finish capturing scenes, select
“No More” and press ENTER.
The Scene List menu appears with all of the
selected scenes.
1 AAB 13:00-14:00 15. 9
2 DEF 20:00-21:00 17. 9
3 AAB 9:00- 9:30 25. 9
4 GHI 0:00-20:30 25. 9
5 DEF 20:00-20:30 15.10
6 L3 21:00-21:30 19.10
Create Playlist
Select the titles you want to capture.
OK
Cancel
Select All
Reset All
Original
Create Playlist - Selected Titles
Select a title to start capturing.
Cancel
Add Title
1 AAB 13:00-14:00 15. 9 0
2 DEF 20:00-21:00 17. 9 0
Scene List
OUT
-
:
- -
:
- -
IN
0:10:26
Capture (Set IN point) 2 DEF 20:00-21:00
IN
OUT
0:23:45
IN
0:10:26
Capture (Set OUT point) 2 DEF 20:00-21:00
Scene List Total 0:33:28 Scenes 2
OK
Quit
Add
Preview
1
2
DEF 20:00-21:00
0:10:26 - 0:23:45
DEF 20:00-21:00
0:25:00 - 0:45:08
Total number of scenes
Total duration of
the selected scene
,continued
70
12Select the scene you want to edit, and
press ENTER.
The sub-menu appears.
“Move”: Changes the scene order.
“Erase”: Erases the scene. The selection is
cancelled.
“Preview”: Displays thumbnail pictures of the
scenes.
“Change IN”: Allows you to change the IN
point, and repeat from step 8.
“Change OUT”: Allows you to change the
OUT point, and repeat from step 9.
To add more scenes, select “Add” and go to
step 6. To preview all of the captured scenes in
the listed order, select “Preview.”
13When you finish editing the Scene List,
select “OK,” and press ENTER.
The display for entering the title name
appears. To enter a new name, select “Enter”
(see page 40).
14Select “OK” to use the default name, and
press ENTER.
To play the Playlist title
Press TOOLS while the Title List menu is turned
on. Then, select “Playlist” and press ENTER.
When the Title List (Playlist) menu appears, select
a title and press
H.
z Hint
When a Playlist title is created, the IN and OUT points
will become chapter marks, and each scene will become
a chapter.
Note
The picture may pause when the edited scene is played.
Moving a Playlist title (Move)
You can change the Playlist title order within the
Title List (Playlist).
1 Press TITLE LIST to turn on the Title List
(Playlist) menu.
If the Title List (Original) menu appears, press
TOOLS and select “Playlist.”
2 Select “Number” in the “Sort” column,
and press ENTER.
The titles are sorted in order of title number.
3 Select a title, and press ENTER.
The sub-menu appears.
4 Select “Move,” and press ENTER.
5 Select a new location for the title by
pressing M/m, and press ENTER.
The title moves to the new location.
Dividing a Playlist title (Divide)
1 Press TITLE LIST to turn on the Title List
(Playlist) menu.
If the Title List (Original) menu appears, press
TOOLS and select “Playlist.”
2 Select a title, and press ENTER.
The sub-menu appears.
3 Select “Divide,” and press ENTER.
The display for setting the dividing point
appears. The title starts to play in the
background.
4 Select the dividing point by pressing
m/M, and press ENTER.
The display asks for confirmation. To change
the dividing point, select “Change.”
5 Select “OK,” and press ENTER.
The display for entering the title name
appears. To use the same title name as before,
select “No.”
6 Select “Yes,” and press ENTER to enter a
new name.
Follow the explanations on page 40. After you
enter a new name, the title is divided in two.
-
RW
VR
Move
Cancel
1 AAB 13:00 - 14:00
2 DEF 8:00 - 9:00
Where do you want to move this title?
15.9
17.9
Wed
Fri
-
RW
VR
0:12:34
Divide 1 ABC 13:00-14:00
71
Editing
Combining multiple Playlist titles
(Combine)
1 Press TITLE LIST to turn on the Title List
(Playlist) menu.
If the Title List (Original) menu appears, press
TOOLS and select “Playlist.”
2 Press TOOLS to select “Combine,” and
press ENTER.
The display for selecting titles appears.
3 Select a title, and press ENTER.
A number indicating the order in which you
selected the title appears. To cancel the
selection, press ENTER again.
4 Repeat step 3 to select all of the titles you
want to combine.
To cancel all of the selections, select “Reset
All.”
5 Select “OK,” and press ENTER.
The list of titles to be combined appears. To
change the selection, select “Change” and go
to step 3.
6 Select “OK,” and press ENTER.
The display for selecting a title name from
among the selected titles appears. To enter a
new name, select “Enter Text,” and follow the
explanations on page 40.
7 Select a name, and press ENTER.
The titles are combined.
-
RW
VR
Combine
Select the titles to combine.
Cancel
Reset All
1
1 AAB 13:00-14:00 15. 9
2 DEF 20:00-21:00 17. 9
3 AAB 13:00-14:00 28. 9
4 AAB 13:00-14:00 5. 10
OK
Combine
Combine the titles in the following order.
OK Change Cancel
1
2
3
1 AAB 13:00-14:00
3 AAB 13:00-14:00
4 AAB 13:00-14:00
15. 9
28. 9
5.10
72
Dubbing (HDD y DVD)
Before Dubbing
In this section, “dubbing” refers to “copying a
recorded title on the internal hard disk drive
(HDD) to another disc, or vice versa.” You can
select to dub one title at a time (Title Dubbing –
see “Dubbing a Single Title (Title Dub)” on
page 74), or multiple titles all at once (Multiple
Title Dubbing – see “Dubbing Multiple Titles
(Dub Selected Titles)” on page 75).
Before you start, read the following precautions,
which are common to both dubbing methods.
z Hint
This section deals with dubbing to and from the internal
HDD. If you want to record from a digital video camera
connected to the DV IN jack, see “DV Dubbing”
(page 77). To record from equipment connected to the
LINE IN jacks, see “Recording From Connected
Equipment Without a Timer” (page 52).
Before you start…
Select the disc type according to your needs
(page 8). This recorder can record on various
discs.
You cannot record both the main and sub sound
on a DVD+RW, DVD-RW (Video mode),
DVD+R, or DVD-R. For bilingual programs, set
“DVD Bilingual Rec.” to either “Main” (default)
or “Sub” in Options Setup (page 97).
Timer recordings and Synchronized recordings
do not start during dubbing. Before you start,
check the Timer List menu to see if there is any
timer recording due to start during dubbing.
Chapter marks in the original recording do not
remain in the dubbed title. Chapter marks are
entered according to the “Auto Chapter” setting
in Features Setup (page 93).
For a title whose aspect ratio (16:9 or 4:3) is
mixed:
When dubbed from the HDD to DVD-RW
(Video mode) or DVD-R, the picture size is
determined by the setting in “DVD Rec.
Picture Size” (page 49).
When dubbed from HDD to DVD+RW or
DVD+R, the picture size is always 4:3.
When dubbed from HDD to DVD-RW (VR
mode), the originally recorded picture size is
retained.
z Hints
You can dub a Playlist title on a DVD-RW (VR mode)
as an original title on the HDD.
When dubbed from a DVD to the HDD, the picture size
and the sound types originally recorded are retained.
Notes
The recorder may not function as described depending
on the disc status. Follow the instructions that appear on
the screen.
When a message appears and indicates that the control
information is full, erase unnecessary titles (page 65).
You cannot dub from DVD VIDEOs or a DVD
recorded on other DVD equipment to the HDD.
Thumbnails that you have set for the originally
recorded title (page 34) will not be retained in the
dubbed title.
About “Dub Mode”
With this recorder, the recording mode for
dubbing is displayed as “Dub Mode.” Two
dubbing method are available: High-speed
Dubbing and Rec Mode Conversion Dubbing.
Read the following and select according to the
required time, disc space, and picture quality.
Dubbing at high-speed (High-speed Dubbing)
, ////
Allows you to dub what you have stored in the
HDD to a high-speed DVD (4x-speed
DVD+RWs/2x-speed DVD-RWs/8x-speed
DVD+Rs/8x-speed DVD-Rs, or slower versions
of each disc type), without changing the recording
mode. Dubbing speed is increased when the
recording mode of the original title is of a longer
recording mode (such as SLP).
Select “Fast” when selecting the “Dub Mode” in
“Dubbing a Single Title (Title Dub)” (page 74) or
“Dubbing Multiple Titles (Dub Selected Titles)”
(page 75). The minimum required time is as
follows (approximate).
Example: When a 120 minute-title is dubbed to a
high-speed DVD-R in LP mode, dubbing becomes
12 times faster, and takes a minimum of 10
minutes. (120 minutes ÷ 12 = 10 minutes).
-
RW
VR
-
RW
Video
+
RW
+
R
HDD
-
R
HDD
+
RW
-
RW
VR
-
RW
Video
+
R
-
R
73
Dubbing (HDD y DVD)
Note that speeds shown in the table are an
approximate of the maximum dubbing speed.
*1
Maximum recording speed of this recorder.
*2
When dubbing to DVD+Rs, the dubbing speed is
x1-speed.
Notes
High-speed Dubbing is not available for the following
titles:
Titles recorded in HQ+.
– Titles that contain both main and sub sounds (except
DVD-RWs (VR mode)).
Titles recorded in mixed picture size (4:3 and 16:9
etc.), (except DVD-RWs (VR mode)).
– Titles recorded in SLP (DVD+RW/DVD+R only).
When dubbed to a DVD-RW (Video mode)/
DVD+RW/DVD+R/DVD-R, erased pictures may
remain on the disc.
Rec Mode Conversion Dubbing
n ////
Allows you to dub from the HDD to a DVD or vice
versa, in a dubbing mode that differs from the
original recordings. For example, when you dub
an HQ title (data size is large) in SP mode, you can
reduce the data size, saving more titles using less
space.
Select a mode different from the original recording
in “Dub Mode” in the steps of “Dubbing a Single
Title (Title Dub)” (page 74) or “Dubbing Multiple
Titles (Dub Selected Titles)” (page 75).
When an HQ or HQ+ title is converted to another
mode, the recorder automatically assigns an
appropriate bit rate, thus retaining the original
picture quality as much as possible (“Dynamic
VBR Dubbing”).
About “VBR”
VBR (Variable Bit Rate) is an effective method of
allocating a suitable bit amount per second. Fine
detail pictures or dynamically moving pictures are
assigned a larger amount, while static pictures are
assigned less, for optimum picture quality.
z Hint
When you dub an edited title using the Rec Mode
Conversion Dubbing method, pauses between scenes are
smoothed out.
Note
The picture quality will not improve even if a title is
converted to a recording mode of better picture quality.
Dubbing restriction
Some DVD VIDEOs or TV programmes contain
copy protection signals such as “Copy-Never” or
“Copy-Once.” You cannot record such contents on
this recorder (only a grey, blank screen will be
recorded). Be especially careful when dubbing on
a non-rewritable DVD such as a DVD-R.
* Version 1.1 CPRM-compatible DVD-RW (VR mode)
only (page 8).
Speed
*1
x2.4-speed x2-speed x4-speed
Rec
mode
High-
speed
DVD+RW
High-
speed
DVD-RW
High-
speed
DVD+R/
DVD-R
HQ x2.4 x2 x4
HSP x3.6 x3 x6
SP x4.8 x4 x8
LP x7.2 x6 x12
EP x9.6 x8 x16
SLP x1 x12 x24
*2
HDD
+
RW
-
RW
VR
-
RW
Video
+
R
-
R
Copy
protection
signals
Original
recording
Dubbing
Copy-Free
Copy-Once
Copy-Never
recorded in grey.
Variable bit rate (adopted
for this recorder)
Average distribution rate
Fixed bit rate
Average distribution rate
More bits
are required
Wasted bits
HDD
-
RW
VR
-
RW
Video
+
RW
-
R
+
R
-
RW
VR
-
RW
Video
+
RW
-
R
+
R
HDD
HDD
-
RW
VR
*
recorded in grey.
,
74
Dubbing a Single Title (Title
Dub)
1 Insert the DVD that you are going to dub to
or from.
2 Select the source by pressing HDD or DVD.
3 Press TITLE LIST to turn on the Title List
menu.
4 Select a title and press ENTER.
The sub-menu appears.
5 Select “Dubbing” and press ENTER.
The display for selecting the dubbing mode
appears.
A Size of the title (approximate)
B Direction of dubbing.
C Available space on the disc to be
dubbed (approximate).
D Information about the title to be
dubbed.
E Dubbing mode and the space that
remains after dubbing (approximate).
6 Select “Dub Mode.
7 Select a dubbing mode by pressing M/m.
* Appears when High-speed Dubbing is available
for the title (page 72).
8 Select “Start,” and press ENTER.
To automatically adjust the dubbing mode
(Auto Dub Mode)
The recorder adjusts the dubbing mode in order to
fit a title on the disc. If there is insufficient disc
space in the selected dubbing mode, the following
display appears after step 8.
Select “Auto Dub mode” and press ENTER to start
dubbing. To manually select another dubbing
mode, select “Reset,” and go to step 7.
To stop dubbing
Press TOOLS to turn on the TOOLS menu. Or,
while the Title List menu is displayed, press
ENTER to display the sub-menu. Select “Stop
Dubbing,” and press ENTER. When asked for
confirmation, select “Yes,” and press ENTER.
z Hints
If disc space is still insufficient for the selected dubbing
mode, erase unnecessary parts of the title, or free up
disc space by erasing titles on the disc (page 67).
You can turn off the recorder without affecting the
dubbing. Press "/1 during dubbing.
You can start Title Dubbing by selecting “DUBBING”
from the System Menu.
-
RW
VR
-
RW
Video
+
RW
+
R
HDD
-
R
1 2 3
4 5 6
7 8 9
0
HDD
DVD
TITLE LIST
TOOLS
M/m, ENTER
CancelSP 2.0GB
Dub Mode
Start
2.0GB 2.6GB
Title Dub
This title will be dubbed. Set the dub mode.
1 World Cup Final
Rec Mode : SP
Fast* t HQ t HSP t SP
SLP T EP T LP
t
T
Fast* t HQ t HSP t SP
SLP T EP T LP
Reset
CancelAuto Dub mode
Title Dub
There is not enough memory for the dubbing,
Select "Auto Dub Mode" or adjust the mode.
75
Dubbing (HDD y DVD)
Dubbing Multiple Titles
(Dub Selected Titles)
1 Insert the DVD that you are going to dub to
or from.
2 Select the source by pressing HDD or DVD.
3 Press TITLE LIST to turn on the Title List
menu.
4 Press TOOLS.
The TOOLS menu appears.
5 Select “Dub Selected Titles,” and press
ENTER.
The display for selecting titles appears.
6 Select titles in the order you want to dub,
and press ENTER.
The titles are numbered in the selected order.
To cancel the selection, press ENTER again.
7 Repeat step 6 to select all of the titles you
want to dub.
To make adjustments for each of the titles,
select “Settings” (see “Making settings for
each title” below). To cancel all of the
selections, select “Reset,” and go to step 6.
8 Select “Start,” and press ENTER.
Adjusting the settings for each title
You can make detailed settings for each of the
selected titles during Multiple Title Dubbing.
1 In step 7 of “Dubbing Multiple Titles (Dub
Selected Titles)” (page 75), select
“Settings” and press ENTER.
The following display for making the
adjustments appears. To re-select titles, select
“Change,” and go to step 6 of “Dubbing
Multiple Titles (Dub Selected Titles)” above.
To have the recorder adjust the dubbing mode
so all of the selected titles fit in, select “Auto
Mode.
A Total size of the selected titles.
B Direction of dubbing.
C Available space on the disc to be
dubbed (approximate).
D Information about the title to be dubbed
(title name, original recording mode,
dubbing mode, and data size after
dubbing).
E Order of dubbing.
2 Select the title which you want to adjust,
and press ENTER.
The sub-menu appears.
“Dub Mode”: Selects the dubbing mode for
each title (see page 72).
-
RW
VR
-
RW
Video
+
RW
+
R
HDD
-
R
1 2 3
4 5 6
7 8 9
0
HDD DVD
TITLE LIST
TOOLS
M/m, ENTER
0.0GB 4.6GBDub Selected Titles
Select title(s) in the order you want to dub them.
Cancel
Reset
1
2
3
4
World Tour – Asia 1
World Tour – Asia 2
World Cup Final
World Tour – Asia 3
11.6
18.6
20.6
25.6
Start
Settings
Dub Selected Titles
Start
Cancel
Auto mode
Change
World Tour – Asia 1
Rec Mode: SP Dub Mode: Fast 0.3GB
World Tour – Asia 2
Rec Mode: SP Dub Mode: Fast 0.3GB
World Tour – Asia 3
Rec Mode: SP Dub Mode: Fast 0.3GB
World Cup Final
Rec Mode: SP Dub Mode: Fast 1.2GB
11.6
18.6
25.6
20.6
1
2
3
4
2.1GB 4.6GB
Adjust the settings for the dubbing here.
,continued
76
“Change Order”: Moves the title to change the
dubbing order. Press M/m to select a new
location, and press ENTER.
“Cancel”: Cancels the title selection. The title
is excluded from dubbing.
3 Select an option, and press ENTER.
4 When you finish making adjustments,
select “Start,” and press ENTER.
To automatically adjust the dubbing mode
(Auto Dub Mode)
The recorder adjusts the dubbing mode so all of
the titles fit in. The same dubbing mode is set for
all of the titles. If disc space is insufficient for the
selected dubbing mode, the following display
appears after step 8 of “Dubbing Maltiple Titles”
(page 75).
Select “Auto Dub mode” and press ENTER. If you
have selected only one title, select “OK.”
To stop dubbing
Press TOOLS to turn on the TOOLS menu. Select
“Stop Dubbing” and press ENTER. When asked
for confirmation, select “Yes,” and press ENTER.
z Hints
You can turn off the recorder without affecting the
dubbing. Press "/1 during dubbing.
You can start Multiple Title Dubbing by selecting
“DUBBING” from the System Menu.
Change
CancelAuto Dub mode
Dub Selected Titles
There is not enough memory. Select
"Auto Dub Mode" or change the selection.
77
DV Dubbing (DV t HDD/DVD)
DV Dubbing (DV t HDD/DVD)
Before DV Dubbing
This section explains dubbing with a digital video
camera via the DV IN jack on the front panel. If
you want to dub by way of the LINE IN jacks, see
“Recording From Connected Equipment Without
a Timer” on page 52.
To record from the DV IN jack
The DV IN jack on this recorder conforms to the
i.LINK standard. You can connect any other
equipment that has an i.LINK (DV) jack, and
record digital signals.
Follow the instructions in “Preparing for
recording using the DV IN jack,” and then move
on to the section on dubbing. For more
information about i.LINK, see “About i.LINK”
(page 106).
z Hint
If you plan to do additional editing on a disc after the
initial dub, use the DV IN jack and record on a DVD-RW
(VR mode) or HDD.
Preparing for recording using the DV
IN jack
You can connect a digital video camera to the DV
IN jack on the recorder to record or edit from a DV
format tape. Operation is straightforward because
the recorder will fast forward and rewind the tape
for you – you do not need to operate your digital
video camera. Do the following to start using the
“DV Edit” functions of this recorder.
See the instruction manual supplied with the
digital video camera as well before connecting.
Notes
The DV IN jack is for input only. It will not output
signals.
You cannot use the DV IN jack when:
– your digital video camera does not work with this
recorder. Connect the camera to the LINE IN jack
and follow the instructions of “Recording From
Connected Equipment Without a Timer” (page 52).
– the input signal is not in DVC-SD format. Do not
connect a MICRO MV format digital video camera
even if it has an i.LINK jack.
– the images on the tape contain copy protection
signals, which limit recording.
If you want to play the disc on other DVD equipment,
finalize the disc (page 37).
Hookups
DVD recorder
To DV IN
i.LINK cable
(not supplied)
DV output
Digital video camera
: Signal flow
1 2 3
4 5 6
7 8 9
0
TOOLS
M/m, ENTER
REC MODE
Z
INPUT
SELECT
DVD
HDD
,continued
78
1 Press HDD or DVD.
If you select DVD, press Z (open/close) and
place a DVD on the disc tray. Press Z again
to close the disc tray.
Wait until “LOAD” disappears from the front
panel display.
If you use an unused DVD, formatting starts
automatically.
2 Insert the source DV format tape into your
digital video camera.
For the recorder to record or edit, your digital
video camera must be set to video playback
mode.
3 Press INPUT SELECT on the remote
repeatedly to select “DV.”
The front panel display changes as follows:
4 Press REC MODE on the remote repeatedly
to select the recording mode.
The recording mode changes as follows:
For details about the recording mode, see
page 41.
5 Press TOOLS on the remote to select “DV
Audio Input,” and press ENTER. Then,
select the setting for the audio input.
“Stereo1” (default): Records original sound
only. Normally select this when dubbing a DV
format tape.
“Mix”: Records both stereo 1 and 2.
“Stereo2”: Records additional audio only.
Select “Mix” or “Stereo2” only if you have
added a second audio channel when recording
with your digital video camera.
You are ready to start dubbing. Select one of
the dubbing methods on the following pages.
z Hints
You can turn off the recorder during dubbing. The
recorder completes dubbing even after being turned
off.
You can adjust the settings for the recording picture
before recording. See “Adjusting the recording picture
quality and size” (page 49).
Notes
You cannot connect more than one piece of digital
video equipment to the recorder.
You cannot control the recorder using another device
or another recorder of the same model.
You cannot record date, time, or the contents of the
cassette memory onto the disc.
If you record from a DV format tape with a sound track
that is recorded in multiple sampling frequencies (48
kHz, 44.1 kHz, or 32 kHz), no sound or an unnatural
sound will be output when playing back the sampling
frequency switch point on the disc.
In order to use this recorder’s Auto Scene Chaptering
function (pages 79, 80), be sure to correctly set the
clock on your digital video camera before shooting.
The recorded picture may be momentarily affected if
the picture size of the source image changes, or if there
is nothing recorded on the tape.
With the recording side facing down
L2L1 L4L3 DV
Programme
position
HQ SP LP EPHSP SLP
79
DV Dubbing (DV t HDD/DVD)
Recording an Entire DV
Format Tape (One Touch
Dubbing)
You can record the entire contents of a DV format
tape onto a disc with a single press of the ONE
TOUCH DUBBING button. The recorder controls
the digital video camera for the whole process, and
completes the recording.
How chapters are created
The dubbed contents on the disc become one title,
and the title is divided into chapters. For the HDD
and a DVD-RW (VR mode), every shooting on the
tape becomes a chapter on the disc (Auto Scene
Chaptering function). For other discs, the recorder
divides the title in either 6 or 15-minute intervals,
according to the setting in “Auto Chapter” in
Features Setup.
Follow steps 1 to 5 of “Preparing for recording
using the DV IN jack” (page 77), and press
ONE TOUCH DUBBING on the remote.
The recorder rewinds the tape and then starts
recording the tape contents.
When the recording is finished, the recorder
rewinds the tape in the digital video camera.
To stop during recording
Open the remote’s cover and press x REC STOP.
Note that it may take a few seconds for the
recorder to stop recording.
z Hints
If you set “Finalize Disc” to “Auto” in Features Setup
(page 96), the recorded disc (except DVD-RW(VR
mode)) will automatically be finalized after recording
is finished.
You can play back a previously recorded title on the
HDD while One Touch Dubbing is in progress.
Notes
When a blank space between the recordings on the tape
continues for more than five minutes, One Touch
Dubbing ends automatically.
The recorder records a blank for five minutes before it
stops dubbing. To stop the blank recording, press
x
REC STOP.
-
RW
VR
-
RW
Video
+
RW
-
R
+
R
HDD
ONE TOUCH
DUBBING
x
REC STOP
80
Program Edit
You can select scenes from a DV format tape, and
then automatically record selected scenes to a disc
of your choice.
To use this function, you will do the following:
m
Using the recorder’s remote control, fast forward
or rewind the tape to select the scenes. At this
point, the selected scenes are not copied to the
disc. The recorder only remembers the IN and
OUT points of the scenes that you selected for
dubbing. You can also reset, erase, or change the
order of the scenes.
m
After you have selected the scenes, the recorder
will fast forward and rewind the tape
automatically and record the scenes to a disc of
your choice.
How chapters are created
The dubbed contents on the disc become one title,
and the title is divided into chapters. For a DVD-
RW (VR mode) and the HDD, every shooting on
the tape and each selected scene becomes a
chapter on the disc (Auto Scene Chaptering
function). For other discs, the recorder divides the
title in either 6 or 15-minute intervals, according
to the setting in “Auto Chapter” in Features Setup.
1 Follow steps 1 to 5 of “Preparing for
recording using the DV IN jack” (page 77),
and press SYSTEM MENU.
2 Select “DV EDIT,” and press ENTER.
The display asks if you want to start selecting
scenes.
If you have previously saved a program, the
display asks if you want to edit an existing
program or to create a new program. To
resume editing the existing program, select
“Saved Data,” and go to step 6.
Connect your digital video camera and
prepare for recording
Select and edit the scenes you want to dub
Dub the selected scenes to a disc
-
RW
VR
-
RW
Video
+
RW
-
R
+
R
HDD
1 2 3
4 5 6
7 8 9
0
</M/m/,,
ENTER
m/M
x REC
STOP
H
SYSTEM
MENU
Scenes Selection
Do you want to select a scene?
Start Cancel
81
DV Dubbing (DV t HDD/DVD)
3 Select “Start,” and press ENTER.
The display for setting the IN point (start of
the scene) appears.
The scene starts to play in the background.
4 Select the IN point by pressing m/M,
and press ENTER.
The display for setting the OUT point (end of
the scene) appears. The scene starts to play in
the background from the IN point.
5 Select the OUT point by pressing m/M,
and press ENTER.
The display asks if you want to add the
selected scene to the Scene List menu. To
preview the scene, select “Preview.” To reset
either the IN or OUT point, select “Change
IN” or “Change OUT,” and repeat from step
4.
6 Select “OK,” and press ENTER.
A new Scene List menu appears with the
selected scene.
A Thumbnail picture
B Time information
C Total duration of the program
D Total number of scenes
7 When you finish adding scenes, select the
scene you want to edit, and press ENTER.
The sub-menu appears.
“Move”: Changes the scene order. Follow the
explanations on the screen to change the order
by pressing M/m and ENTER.
“Erase”: Erases the scene. When asked for
confirmation, select “OK.”
“Preview”: Plays the selected scene.
“Change IN”: Changes the start of the scene.
Repeat from step 4.
“Change OUT”: Changes the end of the scene.
Repeat from step 5.
8 When you finish editing the Scene List,
select “OK,” and press ENTER.
The display for entering the title name
appears. To enter a new name, select “Enter,”
and follow the explanations on page 40.
Select scene (Set IN point)
OUT
-
:
- -
:
- -
IN
0:00:30
Controlling...
Select scene (Set OUT point)
OUT
0:00:52
IN
0:00:30
Controlling...
Scenes Selection
Do you want to capture the scene
between IN 0:00:30 and OUT 0:00:52?
OK Cancel
Preview Change IN Change OUT
SCENE LIST
Total 0:00:22 Scenes 1
OK
Quit
Add
0:00:30-0:00:52
Duration 0:00:22
1
Title Name
Enter the title name.
DV 11.10.2003 13:30 - 12.11.2003 16:46
OK Enter
,continued
82
9 Select “OK,” and press ENTER.
The default title name is fixed, and the display
asks if you want to start recording. To change
the disc media, select “Media” and press M/m.
To change the dubbing mode, select “Dub
Mode” and press M/m.
10Select “Start,” and press ENTER.
The recorder starts recording the tape contents
as programmed.
If the recording does not fit due to the
dubbing mode you selected, the display asks
if you want to continue. To change the
dubbing mode, select “Reset” and repeat
from step 9. To have the recorder adjust the
dubbing mode, select “Auto Dub Mode.”
If there is not enough disc space even after
changing the dubbing mode, the display
asks if you want to record halfway. To
continue, select “OK.”
To stop during recording
Open the remote’s cover and press x REC STOP.
Note that it may take a few seconds for the
recorder to stop recording.
Notes
The disc may not be recorded as programmed if the
tape’s time code is not sequential or there are blanks
between the recordings on the tape. In this case, see
“Recording From Connected Equipment Without a
Timer” (page 52).
The start and end points of a program may be different
from what you have set if the source DV format tape is
in any of the following conditions:
– Recording mode was changed during the recording.
– There is a blank space in the recorded portion of the
tape.
If you set the beginning of the tape as the IN point and
the end point as the OUT point, the IN and OUT points
may change slightly during dubbing.
You cannot set a scene to be shorter than one second.
Cancel
Start
DV Dubbing
2.6GB
Change the dubbing mode if necessary.
Select "Start" to start dubbing.
DVD
Media Dub Mode
SP 0.8GB
Data capacity required for the dubbing.
83
Settings and Adjustments
Settings and Adjustments
Using the Setup Displays
By using the Setup Displays, you can make
various adjustments to items such as picture and
sound, as well as select a language for the
subtitles.
The Setup Displays are used in the following way.
Note
Playback settings stored in some titles take priority over
the Setup Display settings, and not all of the functions
described may work.
1 Press SYSTEM MENU while the recorder is
in stop mode.
The System Menu appears.
2 Select “SETUP,” and press ENTER.
The Setup Display appears.
3 Select “Settings,” “Video,” “Audio,”
“Features,” “Options,” or “Easy Setup,
and press ENTER.
The selected Setup Display appears.
Example: “Video” setup
4 Select the item you want to set up, and
press ENTER.
Available options for the item appear.
Example: “TV Type”
Some items display a dialogue box that
provides further detailed settings.
Example: The following dialogue box appears
when “Parental Control” in Features Setup is
selected.
1 2 3
4 5 6
7 8 9
0
</M/m/,,
ENTER
SYSTEM
MENU
SYSTEM MENU
TITLE LIST
TIMER
TIMER LIST
DV EDIT
DUBBING
SETUP
SETUP
Settings
Video
Audio
Features
Options
Easy Setup
Channel Setting
Channel List
Clock
Language
Settings
Video
Audio
Features
Options
Easy Setup
TV Type :
Pause Mode :
Component Out :
Progressive Mode :
Screen Saver :
Scart Setting
Line4 Input :
16 : 9
Auto
Off
Auto
On
Video
SETUP
Settings
Video
Audio
Features
Options
Easy Setup
SETUP
TV Type :
Pause Mode :
Component Out :
Progressive Mode :
Screen Saver :
Scart Setting
Line4 Input :
16 : 9
Auto
Off
Auto
On
Video
16 : 9
4 : 3 Letter Box
4 : 3 Pan Scan
Features - Parental Control
Enter your password.
OK
Cancel
,continued
84
In this case, see “Parental Control” in
“Recording and Parental Control Settings
(Features)” (page 93).
5 Select an option, and press ENTER.
The currently selected option is displayed
next to the setup item.
Example: when “4:3 Letter Box” is set.
To turn off the display
Press SYSTEM MENU repeatedly.
Aerial Reception and
Language Settings
(Settings)
The Settings Setup helps you to make tuner, clock,
and channel settings for the recorder.
Select “Settings” in the Setup Display. To use the
display, see “Using the Setup Displays” (page 83).
Channel Setting
Presets channels manually.
If some channels could not be set using the Easy
Setup function, you can set them manually.
If there is no sound or if the picture is distorted, the
wrong tuner system may have been preset during
Easy Setup. Set the correct tuner system manually
in the steps below.
1 Follow steps 1 to 3 of “Using the Setup
Displays” (page 83) to select “Settings” in the
Setup Display.
2 Select “Channel Setting,” and press ENTER.
3 Press PROG +/– to select the programme
position.
Settings
Video
Audio
Features
Options
Easy Setup
SETUP
TV Type :
Pause Mode :
Component Out :
Progressive Mode :
Screen Saver :
Scart Setting
Line4 Input :
4 : 3 Letter Box
Auto
Off
Auto
On
Video
Settings
Video
Audio
Features
Options
Easy Setup
Channel Setting
Channel List
Clock
Language
SETUP
Settings - Channel Setting
Prog. 1
System :
Normal / CATV :
Channel Set :
Station Name :
PAY - TV / CANAL+ :
Audio :
BG
Normal
C3
AAB
Off
NICAM
Settings - Channel Setting
Prog. 8
System :
Normal / CATV :
Channel Set :
Station Name :
PAY - TV / CANAL+ :
Audio :
BG
Normal
C2
CDE
Off
NICAM
Selected programme position
85
Settings and Adjustments
4 Select “System,” and press ENTER.
5 Select an available TV system, BG, DK, I, or
L, and press ENTER (page 86).
6 Select “Normal/CATV,” and press ENTER.
7 Select “Normal,” and press ENTER.
To set CATV (Cable Television) channels,
select “CATV.”
8 Select “Channel Set,” and press ENTER.
9 Press M/m repeatedly until the channel you
want is displayed, then press ENTER.
The channels are scanned in the order shown
in the table below.
If you know the number of the channel you
want, press the number buttons. For
example, for channel 5, first press “0” and
then press “5.” Then press ENTER.
10 Select “Audio,” and press ENTER.
11 Select “NICAM,” and press ENTER.
12 Select “AFT” and press ENTER.
13 Select “On” to turn on AFT, and press
ENTER.
If the Auto Fine Tuning function does not
work effectively, select “Off” and press
ENTER. When the fine tuning bar appears,
press </, to obtain a clearer picture, and
press ENTER.
To preset another channel, repeat from step 3.
BG Select this when in West European
countries, except those listed in
“Receivable channels” (page 86).
DK Select this when in East European
countries.
I Select this when in Great Britain/
Ireland.
L Select this when in France.
Settings - Channel Setting
Prog. 8
System :
Normal / CATV :
Channel Set :
Station Name :
PAY - TV / CANAL+ :
Audio :
BG
Normal
C1
ARD
On
NICAM
BG
DK
I
L
Settings - Channel Setting
Prog. 8
System :
Normal / CATV :
Channel Set :
Station Name :
PAY - TV / CANAL+ :
Audio :
BG
Normal
C1
CDE
Off
NICAM
Normal
CATV
Settings - Channel Setting
Prog. 8
System :
Normal / CATV :
Channel Set :
Station Name :
PAY - TV / CANAL+ :
Audio :
BG
Normal
C1
CDE
Off
NICAM
C2
NICAM Normally, select this.
Standard Select this if the sound from
NICAM broadcasts is not
clear.
On
Turns on the Auto Fine
Tuning function. Normally,
select this.
Off Allows you to adjust the
pictures manually.
Settings - Channel Setting
Prog. 8
System :
Normal / CATV :
Channel Set :
Station Name :
PAY - TV / CANAL+ :
Audio :
BG
Normal
C5
CDE
Off
NICAM
NICAM
Standard
Settings - Channel Setting
Prog. 8
Normal / CATV :
Channel Set :
Station Name :
PAY - TV / CANAL+ :
Audio :
AFT :
Normal
C5
CDE
Off
NICAM
On
On
Off
Fine Tuning
Prog. 8
,continued
86
Receivable channels
Station Name
Changes or enters a new station name (up to 5
characters). The recorder must receive channel
information (for instance, SMARTLINK
information) for station names to appear
automatically.
1 Follow steps 1 to 3 of “Using the Setup
Displays” (page 83) to select “Settings” in the
Setup Display.
2 Select “Channel Setting,” and press ENTER.
3 Press PROG +/– to select the programme
position for which you want to change or enter
a station name.
4 Select “Station Name,” and press ENTER.
The display for entering characters appears.
To enter characters, see page 40.
5 Select “Finish,” and press ENTER.
PAY-TV/CANAL+
Sets the PAY-TV/Canal Plus channels.
For details, see page 30.
Channel List (Changing/Disabling
the channels)
Changes or disables the programme positions after
setting the channels. If any programme positions
are unused or contain unwanted channels, you can
disable them.
You can also change station names. If the station
names are not displayed, you can enter them
manually.
1 Follow steps 1 to 3 of “Using the Setup
Displays” (page 83) to select “Settings” in the
Setup Display.
2 Select “Channel List,” and press ENTER.
3 Press M/m to select the row containing the
programme position you want to change or
disable.
To change, press ENTER and go to step 4.
To disable, press CLEAR and go to step 6.
The disabled positions will be skipped when
you press PROG +/–.
To display other pages for programme
positions 7 to 99, press M/m repeatedly.
TV system Channel coverage
BG (West European
Countries, except
those listed below)
E2 - E12 VHF
Italia A – H VHF
E21 – E69 UHF
S1 – S20 CATV
S21 – S41 HYPER
S01 – S05 CATV
DK (East European
Countries)
R1 – R12 VHF
R21 – R69 UHF
S1 – S20 CATV
S21 – S41 HYPER
S01 – S05 CATV
I (Great Britain/
Ireland)
Ireland A – J VHF
South Africa 4 – 13 VHF
B21 – B69 UHF
S1 – S20 CATV
S21 – S41 HYPER
S01 – S05 CATV
L (France) F2 – F10 VHF
F21 – F69 UHF
B – Q CATV
S21 – S41 HYPER
Settings - Channel Setting
Prog. 1
System :
Normal / CATV :
Channel Set :
Station Name :
PAY - TV / CANAL+ :
Audio :
BG
Normal
C3
AAB
Off
NICAM
AAB
"A"
"a"
Symbol
Cancel
Finish
Space
Clear All
Back
,. - 1
BA C 2
ED F 3
HG I 4
KJ L5
1
2
3
4
5
NM O 6
QP R S
UT V 8
XW Y Z
7
9
0
6
7
8
9
0
Input Station Name
Settings - Channel List
Prog
1
2
3
4
5
6
Channel
Name
AAB
FGH
PQR
C3
C5
C12
C21
C23
C24
87
Settings and Adjustments
4 Press M/m until the selected channel row
moves to the desired programme position.
The selected channel is inserted at the new
programme position.
5 Press ENTER to confirm the setting.
6 To change or disable the programme position
of another station, repeat from step 3.
Note
Be sure to correctly select the programme position you
want to disable. If you disable the wrong programme
position by mistake, you need to reset that channel
manually.
Clock
Auto Adjust
Turns on the Auto Clock Set function when a channel
in your local area broadcasts a time signal.
1 Follow steps 1 to 3 of “Using the Setup
Displays” (page 83) to select “Settings” in the
Setup Display.
2 Select “Clock,” and press ENTER.
3 Select “Auto Adjust,” and press ENTER.
4 Select “On,” and press ,.
5 Press M/m repeatedly until the programme
position of the station that carries a time signal
appears, and press ENTER.
If the recorder does not receive a time signal
from any station, “Auto Adjust” returns to
“Off” automatically and the menu for setting
the clock manually appears on the screen.
z Hint
If you set “Auto Adjust” to “On,” the Auto Clock Set
function is activated whenever the recorder is turned off.
Note
The Auto Clock Set function does not work while the
recorder is standing by for Synchro-Recording.
To set the clock manually
If the Auto Clock Set function did not set the clock
correctly for your local area, try another station for
the Auto Clock Set function or set the clock
manually.
1 Follow steps 1 to 3 of “Using the Setup
Displays” (page 83) to select “Settings” in the
Setup Display.
2 Select “Clock,” and press ENTER.
3 Select “Auto Adjust,” and press ENTER.
4 Select “Off,” and press ENTER.
5 Select “Present Time,” and press ENTER.
6 Press M/m to set the day, and press ,.
Set the month, year, hour, and minutes in
sequence. Press </, to select the item to be
set, then press M/m to set the numbers. The
day of the week is set automatically.
To change the numbers, press < to return to
the item to be changed, and press M/m.
7 Press ENTER to start the clock.
Settings - Channel List
Prog
1
2
3
4
5
6
Channel Name
AAB
FGH
PQR
C3
C12
C21
C5
C23
C24
Settings - Clock
Auto Adjust : Off 1
Present Time : Thu 1. 1. 2004. 21:39
Settings - Clock
Auto Adjust : Off 1 ARD
Present Time : Thu 1. 1. 2004. 21:39
Off 1
Settings - Clock
Auto Adjust : Off 1 ARD
Present Time : Thu 1. 1. 2004. 21:39
On 1
Settings - Clock
Auto Adjust : Off 1 ARD
Present Time : Thu 1. 1. 2004. 21:39
Off 1
Clock - Present Time
Set the time and date manually.
0 00:
1 2004
Thu 1
,continued
88
Language
OSD (On-Screen Display)
Switches the display language on the screen.
DVD Menu (DVD VIDEO only)
Switches the language for the DVD menu.
Audio (DVD VIDEO only)
Switches the language of the sound track.
When you select “Original,” the language given
priority in the disc is selected.
Subtitle (DVD VIDEO only)
Switches the language of the subtitles recorded on
the disc.
When you select “Audio Follow,” the subtitle
language changes according to the language you
selected for the sound track.
z Hint
If you select “Others” in “DVD Menu,” “Subtitle,” or
“Audio,” select and enter a language code from
“Language Code List” (page 114) using the number
buttons.
Note
If you select a language in “DVD Menu,” “Subtitle,” or
“Audio” that is not recorded on the DVD VIDEO, one of
the recorded languages will be automatically selected.
Video Settings (Video)
Video settings will adjust items related to the
image, such as size and colour.
Choose the settings according to the type of TV,
tuner, or decoder connected to the DVD recorder.
1 Press SYSTEM MENU while the recorder is
in stop mode.
2 Select “SETUP,” and press ENTER.
3 Select “Video,” and press ENTER.
The Video Setup appears with the following
options. The default settings are underlined.
TV Type
Selects the aspect ratio of the connected TV (4:3
standard or wide).
16:9 Select this when connecting
to a wide-screen TV or TV
with a wide mode function.
4:3 Letter
Box
Select this when connecting
to a 4:3 screen TV. Displays
a wide picture with bands on
the upper and lower portions
of the screen.
4:3 Pan
Scan
Select this when connecting
to a 4:3 screen TV.
Automatically displays a
wide picture on the entire
screen and cuts off the
portions that do not fit.
Settings
Video
Audio
Features
Options
Easy Setup
SETUP
TV Type :
Pause Mode :
Component Out :
Progressive Mode :
Screen Saver :
Scart Setting
Line4 Input :
16 : 9
Auto
Off
Auto
On
Video
89
Settings and Adjustments
Note
Depending on the disc, “4:3 Letter Box” may be selected
automatically instead of “4:3 Pan Scan” or vice versa.
Pause Mode (HDD/DVDs only)
Selects the picture quality in pause mode.
Component Out
Selects whether or not to output video signals
from the COMPONENT VIDEO OUT jacks.
Notes
When you set “Line1 Output” to “RGB,” you cannot
set “Component Out” to “On.”
When you connect the recorder to a monitor or
projector via only the COMPONENT VIDEO OUT
jacks, do not select “Off.” If you select “Off” in this
case, the picture may not appear.
Progressive Mode
DVD software can be divided into two types: film
based software and video based software. Video
based software is derived from TV, such as
dramas and sit-coms, and displays images at 30
frames/60 fields (25 frames/50 fields) per second.
Film based software is derived from film and
displays images at 24 frames per second. Some
DVD software contains both Video and Film.
In order for these images to appear natural on your
screen when output in PROGRESSIVE mode (50
or 60 frames per second), the progressive video
signal needs to be converted to match the type of
DVD software that you are watching.
You can fine-tune the progressive 525p/625p
video signal that is output when you press
PROGRESSIVE (“PROGRESSIVE” lights up).
Note that you must connect to a progressive
format TV using the COMPONENT VIDEO OUT
jacks (page 15).
Screen Saver
The screen saver image appears when you do not
use the recorder for more than 10 minutes while an
on-screen display, such as the System Menu, is
displayed on your TV screen. The screen saver
image helps prevent your display device from
becoming damaged (ghosting).
Auto The picture, including subjects
that move dynamically, is output
with no jitter. Normally select this
position.
Frame The picture, including subjects
that do not move dynamically, is
output in high resolution.
On Outputs the component video
signals. Select this when you want
to view progressive signals.
Off
Outputs no signals.
16:9
4:3 Letter Box
4:3 Pan Scan
Auto Automatically detects the
software type (Film-based or
Video-based) and selects the
appropriate conversion mode.
Normally select this position.
Video Fixes the conversion mode to the
mode for Video-based software.
On
Turns on the screen saver
function.
Off Turns off the function.
,continued
90
Scart Setting
Sets the method of inputting/outputting signals
from the SCART jacks on the rear panel of the
recorder. Select an option for each of the items
below according to the combination of jacks and
methods that you are going to use.
Line1 Output
Selects a method of outputting video signals for
the LINE 1-TV jack.
Notes
If your TV does not accept S-video or RGB signals, no
picture appears on the TV screen even if you select “S
Video” or “RGB.” See the instructions supplied with
your TV.
You cannot select ”RGB” when “Component Out
above is set to “On.”
SMARTLINK is available only when “Video” is
selected.
Line3 Input
Selects a method of inputting video signals for the
LINE 3/DECODER jack. The picture will not be
clear if this setting does not match the type of
video input signal.
Line3 Output
Selects a method of outputting video signals for
the LINE 3/DECODER jack.
Line4 Input
Selects a method of inputting video signals for the
LINE 4 IN jack on the rear panel of the recorder.
RGB Outputs RGB signals.
Video
Outputs video signals.
S Video Outputs S-video signals.
Video/RGB
Inputs video signals or RGB
signals.
Decoder Select this when connecting to a
PAY-TV/Canal Plus decoder.
S Video Inputs S-video signals.
Video
Outputs video signals.
S Video Outputs S-video signals.
Video Inputs video signals.
S Video Inputs S-video signals.
91
Settings and Adjustments
Audio Settings (Audio)
The Audio Setup allows you to adjust the sound
according to the playback and connection
conditions.
1 Press SYSTEM MENU while the recorder is
in stop mode.
2 Select “SETUP,” and press ENTER.
3 Select “Audio,” and press ENTER.
The Audio Setup appears with the following
options. The default settings are underlined.
Audio ATT (attenuation)
If the playback sound is distorted, set this item to
“On.” The recorder reduces the audio output level.
This function affects the output of the following
jacks:
LINE 2 OUT AUDIO L/R jacks
–LINE 1-TV jack
LINE 3/DECODER jack
Audio DRC (Dynamic Range Control) (DVDs
only)
Makes the sound clear when the volume is turned
down when playing a DVD that conforms to
“Audio DRC.” This affects the output from the
following jacks:
LINE 2 OUT AUDIO L/R jacks
LINE 1-TV jack
LINE 3/DECODER jack
DIGITAL OUT (OPTICAL or COAXIAL) jack
only when “Dolby Digital” is set to “D-PCM”
(page 92).
Downmix (DVDs only)
Switches the method for mixing down to two
channels when you play a DVD which has rear
sound elements (channels) or is recorded in Dolby
Digital format. For details on the rear signal
components, see “Checking the Play Information
and Playing Time” (page 38). This function
affects the output of the following jacks:
LINE 2 OUT AUDIO L/R jacks
LINE 1-TV jack
LINE 3/DECODER jack
DIGITAL OUT (OPTICAL or COAXIAL) jack
when “Dolby Digital” is set to “D-PCM”
(page 92).
On Select this when the
playback sound from the
speakers is distorted.
Off
Normally select this
position.
Settings
Video
Audio
Features
Options
Easy Setup
Audio ATT :
Audio DRC :
Downmix :
Digital Out :
Dolby Digital :
MPEG :
DTS :
Off
Standard
Dolby Surround
On
D-PCM
PCM
Off
SETUP
Standard Normally select this
position.
TV Mode Makes low sounds clear
even if you turn the volume
down.
Wide
Range
Gives you the feeling of
being at a live performance.
Dolby
Surround
Normally select this
position.
Multi-channel audio signals
are output to two channels
for enjoying surround
sounds.
Normal Multi-channel audio signals
are downmixed to two
channels for use with your
stereo.
,continued
92
Digital Out
Selects if audio signals are output via the
DIGITAL OUT (OPTICAL or COAXIAL) jacks.
To set the digital output signal
The following setup items switch the method of
outputting audio signals when you connect a
component such as an amplifier (receiver) with a
digital input jack.
For connection details, see “Connecting the Audio
Cords” (page 17).
Select “Dolby Digital,” “MPEG,” and “DTS”
after setting “Digital Out” to “On.”
If you connect a component that does not accept
the selected audio signal, a loud noise (or no
sound) will come out from the speakers, and may
affect your ears or cause speaker damage.
Dolby Digital (HDD/DVDs only)
Selects the type of Dolby Digital signal.
MPEG (DVD VIDEO only)
Selects the type of MPEG audio signal.
DTS (DVD VIDEO only)
Selects whether or not to output DTS signals.
Note
When you use the DIGITAL OUT (COAXIAL) jack to
listen to MPEG audio signals and set “MPEG” to
“MPEG” in Audio Setup, no sound will come from your
speakers if you select one of the TVS modes.
On Normally select this
position. When you select
“On,” seeTo set the digital
output signal for further
settings.
Off The influence of the digital
circuit upon the analogue
circuit is minimal.
D-PCM
Select this when the recorder
is connected to an audio
component lacking a built-in
Dolby Digital decoder. You
can select whether the
signals conform to Dolby
Surround (Pro Logic) or not
by making adjustments to
the “Downmix” item in
Audio Setup (page 91).
Dolby
Digital
Select this when the recorder
is connected to an audio
component with a built-in
Dolby Digital decoder.
Settings
Video
Audio
Features
Options
Easy Setup
Audio ATT :
Audio DRC :
Downmix :
Digital Out :
Dolby Digital :
MPEG :
DTS :
Off
Standard
Dolby Surround
On
D-PCM
PCM
Off
SETUP
PCM Select this when the recorder
is connected to an audio
component without a built-in
MPEG decoder. If you play
MPEG audio sound tracks,
the recorder outputs stereo
signals via the DIGITAL
OUT (COAXIAL) jack.
MPEG Select this when the recorder
is connected to an audio
component with a built-in
MPEG decoder.
On Select this when the recorder
is connected to an audio
component with a built-in
DTS decoder.
Off
Select this when the recorder
is connected to an audio
component without a built-in
DTS decoder.
93
Settings and Adjustments
Recording and Parental
Control Settings (Features)
The Features Setup allows you to adjust recording
and parental control settings.
1 Press SYSTEM MENU while the recorder is
in stop mode.
2 Select “SETUP,” and press ENTER.
3 Select “Features,” and press ENTER.
The Features Setup appears with the
following options. The default settings are
underlined.
TV Direct Rec (HDD/DVD+RW/DVD-RW/
DVD+R/DVD-R only)
Auto Chapter
Automatically divides a recording (a title) into
chapters by inserting chapter markings at a
specified interval. The markings are inserted while
the recording is being made.
Notes
Depending upon the size of the recording being made,
the actual interval may vary from the interval selected
in “Auto Chapter.” The selected interval should only be
used as an approximation to create chapters.
This function is not available when dubbing DV tapes
to HDD and DVD-RWs (VR mode). Chapter marks are
automatically entered where the recordings start on the
tape (pages 79, 80).
TV Guide Page
Some broadcast systems ensure a Teletext
service* in which the complete programmes and
their data (title, date, channel, recording start time,
etc.) are stored day by day. A TV guide page
corresponds to each day of the week. When
recording a programme, the recorder
automatically takes the programme name from the
Teletext pages and stores it as the title name. The
TV guide page numbers depend entirely on the
broadcast itself and may be subject to change. If
so, you may have to set those TV guide page
numbers manually in the TV Guide Page menu.
* Not available in some areas.
1 After step 3 above, select “TV Guide Page”
and press , or ENTER.
The TV Guide Page menu appears.
2 Select the programme position for which you
want to set or change the TV guide page by
pressing PROG +/–.
The TV guide page numbers (Example:
P301) appear automatically when the
recorder detects them.
If no page numbers are detected (P000), you
have to set the appropriate TV guide page
number manually.
On Allows you to easily record
what you are watching on the
TV using SMARTLINK.
Off Turns off the TV Direct Rec
function.
Off No chapter mark is inserted.
6Min
Inserts chapter marks at
approximately 6-minute
intervals.
15Min Inserts chapter marks at
approximately 15-minute
intervals.
Settings
Video
Audio
Features
Options
Easy Setup
TV Direct Rec :
Auto Chapter :
TV Guide Page
Parental Control
One Touch Dubbing
Sychro Rec:
HQ Setting:
Colour System :
On
6 Min
Record to HDD
HQ
PA L
SETUP
Features-TV Guide Page
Prog. 4
Sun
Mon
Tu e
Wed
Thu
Fri
Sat
P 301
P 302
P 303
P 304
P 305
P 306
P 307
Features-TV Guide Page
Prog. 4
Sun
Mon
Tu e
Wed
Thu
Fri
Sat
P 000
P 000
P 000
P 000
P 000
P 000
P 000
,continued
94
3
Select the TV guide page number you want to
modify, and press ENTER.
4 Press the number buttons or </M/m/, to
enter the TV guide page number, and press
ENTER to confirm the setting.
If you make a mistake, press CLEAR to re-
enter the correct number.
To set or change another TV guide page
number, repeat steps 3 and 4 above.
z Hint
To view Teletext information on your TV screen during
a broadcast, switch to your TV’s tuner by pressing t
(TV/video).
Notes
In step 4 above, enter “000” if you do not want to use
the TV guide page number for automatic labelling. The
recorder will instead store a default title name
(programme position, start time - stop time).
Refer to the Teletext information on your TV screen to
obtain the TV guide page number with programme
titles and their start times.
If the Teletext TV guide has a page which always
shows the programmes for the current day, this page
should be input for all days.
If you start recording more than three minutes before
the programme is scheduled to start, the correct label
information may not be transferred.
Note that this function may not work correctly with
programmes broadcast from some stations.
If the broadcast system updates the Teletext
information at the moment recording starts, the title
label may not correspond to the recorded programme.
In this case, you may have to manually enter the correct
title (page 65).
Parental Control (DVD VIDEO only)
Playback of some DVD VIDEOs can be limited
according to a predetermined level, such as the age
of the users. Scenes may be blocked or replaced
with different scenes.
1 After step 3 above, select “Parental Control,”
and press ENTER.
If you have not entered a password, the
display for registering a new password
appears.
When you have already registered a
password, the display for entering the
password appears.
2 Enter your four-digit password using the
number buttons, then select “OK” and press
ENTER.
3 Select “Standard,” and press , or ENTER.
The selection items for “Standard” are
displayed.
Features-TV Guide Page
Prog. 4
Sun
Mon
Tu e
Wed
Thu
Fri
Sat
P 000
P 000
P 000
P 000
P 000
P 000
P 000
0 0 0
P
Features - Parental Control
Enter a new password.
OK
Cancel
Features - Parental Control
Enter your password.
OK
Cancel
Features - Parental Control
Level :
Standard :
Password
Off
USA
Features - Parental Control
Level :
Standard :
Password
Off
Others
USA
Others
95
Settings and Adjustments
4 Select a geographic area as the playback
limitation level, and press ENTER.
The area is selected.
When you select “Others,” press the number
buttons to select and enter an area code in
the table (see below). Then select “OK” and
press ENTER.
5 Select “Level,” and press ENTER.
The selection items for “Level” are displayed.
The lower the value, the stricter the limitation.
6 Select the level, and press ENTER.
The Parental Control setting is complete.
To cancel the Parental Control setting for the
disc, set “Level” to “Off” in step 6.
To change the password, select “Password” in
step 3, and press ENTER. When the display
for registering a password appears, enter a
new four-digit password using the number
buttons, then select “OK” and press ENTER.
Notes
If you forget your password, you will have to reset it by
selecting “Parental Control” under “Factory Setup” in
Options Setup (page 97).
When you play discs which do not have the Parental
Control function, playback cannot be limited on this
recorder.
Depending on the disc, you may be asked to change the
Parental Control level while playing the disc. In this
case, enter your password, then change the level.
Area code
Features - Parental Control
Level :
Standard :
Password
Off
Others
Off
8
7
6
5
4
Standard Code number
Argentina 2044
Australia 2047
Austria 2046
Belgium 2057
Brazil 2070
Canada 2079
Chile 2090
China 2092
Denmark 2115
Finland 2165
France 2174
Germany 2109
India 2248
Indonesia 2238
Italy 2254
Japan 2276
Korea 2304
Malaysia 2363
Mexico 2362
Netherlands 2376
New Zealand 2390
Norway 2379
Pakistan 2427
Philippines 2424
Portugal 2436
Russia 2489
Singapore 2501
Spain 2149
Sweden 2499
Switzerland 2086
Thailand 2528
United Kingdom 2184
,continued
96
One Touch Dubbing
Displays the following options for the One Touch
Dub function.
Finalize Disc (for all recordable discs except
DVD-RW in VR mode)
Selects whether or not to finalize the disc
automatically following One Touch Dubbing
(page 79).
Colour System
Selects the colour system when playing VIDEO
CDs (including Super VCDs).
Synchro Rec
Selects the recording destination used for
Synchro-Recording (page 51).
HQ Setting (HDD only)
Selects the HQ mode used for recording on the
HDD (page 41).
Disc and Remote Control
Settings/Factory Settings
(Options)
The Options Setup allows you to set up other
operational settings.
1 Press SYSTEM MENU while the recorder is
in stop mode.
2 Select “SETUP,” and press ENTER.
3 Select “Options,” and press ENTER.
The Options Setup appears with the following
options. The default settings are underlined.
Format DVD (DVD-RW only)
The recorder automatically starts formatting in
VR mode or Video mode, whichever is selected
below, when a new, unformatted DVD-RW is
inserted.
Auto Automatically finalizes the
disc following One Touch
Dubbing.
Manual
Allows you to finalize the
disc manually.
PAL
Plays a disc in PAL colour
system.
NTSC Plays a disc in NTSC colour
system.
Record to
HDD
Records to the HDD.
Record to
DVD
Records to DVDs.
HQ+ Records in higher quality
(approximate 15 Mbps).
HQ Records in the standard HQ
mode.
VR Automatically formats the
disc in VR mode.
Video Automatically formats the
disc in Video mode.
Settings
Video
Audio
Features
Options
Easy Setup
Format DVD :
HDD Bilingual Rec. :
DVD Bilingual Rec. :
Dimmer :
Auto Display :
Command Mode :
Factory Setup
VR
Main
Main
Normal
On
DVD3
SETUP
97
Settings and Adjustments
HDD Bilingual Rec. (HDD only)
Selects the sound to be recorded on the HDD.
Note
If you set the recording mode to be changed while
dubbing from a DVD to the HDD, the sound recorded in
the source (DVD) is applied regardless of this setting.
DVD Bilingual Rec. (for all recordable discs
except DVD-RW in VR mode)
Selects the sound to be recorded on the recordable
disc. This setting is not necessary when recording
on DVD-RWs (VR mode) that record both the
main and sub sounds.
Dimmer
Adjusts the lighting of the front panel display.
Auto Display
Command Mode
Changes the Command Mode of the recorder if
other DVD equipment is assigned the same
Command Mode. Be sure to match the Command
Mode switch on the remote to the setting made
here. For details, see “If you have a Sony DVD
player or more than one Sony DVD recorder” on
page 21.
Factory Setup
Allows you to select the setup settings by group,
and return them to their default settings. Note that
all of your previous settings will be lost.
1 After step 3 above, select “Factory Setup,”
and press , or ENTER.
The display for selecting a group of settings
appears.
2 Select the group of settings you want to return
to default from “Settings,” “Video,” “Audio,
“Features,” “Options,” “Parental Control,”
and “All,” and press , or ENTER.
3 Select “Start,” and press ENTER.
The selected settings return to their default
settings.
4 Press ENTER when “Finish” appears.
Main Records the main sound for
the bilingual programme.
Sub Records the sub sound for
the bilingual programme.
Main+Sub Records the main and sub
sounds for the bilingual
programme.
Main
Records the main sound for
the bilingual programme.
Sub Records the sub sound for
the bilingual programme.
Normal
Bright lighting.
Power
Save
Low lighting. Turns off the
lighting when the power is
off.
On
Automatically displays
information on the screen
when the recorder is turned
on, etc.
Off Displays information only
when DISPLAY is pressed.
DVD1 Select this if the default
Command Mode conflicts
with other DVD equipment.
DVD2 Select this if the default
Command Mode conflicts
with other DVD equipment.
DVD3
The default Command Mode
of the recorder.
,continued
98
Easy Setup
(Resetting the Recorder)
Select this to run the Easy Setup programme.
1 Press SYSTEM MENU while the recorder is
in stop mode.
2 Select “SETUP,” and press ENTER.
3 Select “Easy Setup,” and press ENTER.
4 Press ENTER.
5 Select “Start,” and press ENTER.
6 Follow the instructions for Easy Setup
(page 22) from step 5.
Settings
Video
Audio
Features
Options
Easy Setup
Easy Setup
SETUP
99
Additional Information
Additional Information
Troubleshooting
If you experience any of the following difficulties
while using the recorder, use this troubleshooting
guide to help remedy the problem before
requesting repairs. Should any problem persist,
consult your nearest Sony dealer.
Power
The power does not turn on.
, Check that the mains lead is connected securely.
Picture
There is no picture.
, Re-connect all connecting cords securely.
, The connecting cords are damaged.
, Check the connection to your TV (page 13).
, Switch the input selector on your TV (such as to
“VCR”) so that the signal from the recorder
appears on the TV screen.
, Check that “Scart Setting” in Video Setup is set
to the appropriate item that conforms to your
system (page 90).
, If you connect the recorder to your TV via only
the COMPONENT VIDEO OUT jacks, set
“Component Out” in Video Setup to “On”
(page 89).
, This recorder cannot record NTSC signals.
Picture noise appears.
, If the picture output signal from your recorder
passes through your VCR to get to your TV, or if
you are connected to a combination TV/VIDEO
player, the copy-protection signal applied to
some DVD programmes could affect picture
quality. If you still experience this problem even
when you connect your recorder directly to your
TV, try connecting your recorder to your TV’s S
VIDEO input.
, You have set the recorder to progressive format
(the PROGRESSIVE indicator lights up) even
though your TV cannot accept the progressive
signal. In this case, press PROGRESSIVE until
the progressive indicator turns off.
, Even if your TV is compatible with progressive
format (525p/625p) signals, the image may be
affected when you set the recorder to progressive
format. In this case, press PROGRESSIVE so
that the PROGRESSIVE indicator turns off and
the recorder is set to normal (interlace) format.
, You are playing a DVD recorded in a colour
system that is different from your TV.
, Noises may appear in the pictures recorded on
the HDD, which is due to the characteristics of
HDD, and is not a malfunction.
TV programme reception does not fill the
screen.
, Set the channel manually in “Channel Setting” in
Settings Setup (page 84).
, Select the correct source using the INPUT
SELECT button, or select a channel of any TV
programme using the PROG +/– buttons.
TV programme pictures are distorted.
, Reorient the TV aerial.
, Adjust the picture (see the TV’s instruction
manual).
, Place the recorder and TV farther apart.
, Place the TV and any bunched aerial cables
farther apart.
, The RF cable is connected to the AERIAL OUT
jack on the recorder. Connect the cable to the
AERIAL IN jack.
TV channels cannot be changed.
, The channel is disabled (page 86).
, A timer recording started, which changed the
channels.
The picture from equipment connected to the
recorder’s input jack does not appear on the
screen.
, If the equipment is connected to the LINE 1-TV
jack, select “L1” in the front panel display by
pressing PROG +/– or INPUT SELECT.
If the equipment is connected to the LINE 2 IN
jacks, select “L2” in the front panel display by
pressing PROG +/– or INPUT SELECT.
If the equipment is connected to the LINE 4 IN
jacks, select “L4” in the front panel display by
pressing PROG +/– or INPUT SELECT.
If the equipment is connected to the LINE 3/
DECODER jack, select “L3” in the front panel
display by pressing PROG +/– or INPUT
SELECT.
,continued
100
If the equipment is connected to the DV IN jack,
(this is usually for a digital video camera
connection), select “DV” in the front panel
display by pressing PROG +/– or INPUT
SELECT.
, When an S video cable is connected to the
recorder’s LINE 4 IN jack, set “Line4 Input” in
Video Setup to “S Video” (page 90).
The playback picture or TV programme from
the equipment connected through the recorder
is distorted.
, If the playback picture output from a DVD
player, VCR, or tuner goes through your recorder
before reaching your TV, the copy-protection
signal applied to some programmes could affect
picture quality. Disconnect the playback
equipment in question and connect it directly to
your TV.
The picture does not fill the screen.
, Set “TV Type” in Video Setup in accordance
with the aspect ratio of your TV (page 88).
The picture does not fill the screen, even
though the aspect ratio is set in “TV Type” in
Video Setup.
, The aspect ratio of the title is fixed.
The picture is black and white.
, Check that “Line1 Output” of “Scart Setting” in
Video Setup is set to the appropriate item that
conforms to your system (page 90).
, If you are using a SCART cord, be sure to use
one that is fully wired (21 pins).
Sound
There is no sound.
, Re-connect all connections securely.
, The connecting cord is damaged.
, The input source setting on the amplifier or the
connection to the amplifier is incorrect.
, The recorder is in reverse play, fast-forward,
slow motion, or pause mode.
, If the audio signal does not come through the
DIGITAL OUT (OPTICAL or COAXIAL)
jacks, check the Audio Setup settings (page 91).
Sound distortion occurs.
, Set “Audio ATT” in Audio Setup to “On”
(page 91).
Sound is noisy.
, When playing a CD with DTS sound tracks,
noise will come from the LINE 2 OUT AUDIO
L/R jacks, LINE 1-TV jack, or LINE 3/
DECODER jack (page 58).
The sound volume is low.
, The sound volume is low on some DVDs.
The sound volume may improve if you set
“Audio DRC” in Audio Setup to “TV Mode”
(page 91).
, Set “Audio ATT” in Audio Setup to “Off”
(page 91).
An alternate audio track cannot be recorded.
, When recording from connected equipment, set
“Line Audio Input” in TOOLS menu to
“Bilingual” (page 52).
, Multilingual tracks (main and sub) cannot be
recorded on DVD+RWs, DVD-RWs (Video
mode), DVD+Rs, or DVD-Rs. To record the
language, select “Main” or “Sub” of “DVD
Bilingual Rec.” in Options Setup before
recording (page 97). To record both the main and
sub sounds, record on a DVD-RW (VR mode).
, Any discs other than the HDD or DVD-RWs
(VR mode) cannot be used for recording both
main and both sounds. To record on the HDD, set
“HDD Bilingual Rec.” in Options Setup to
“Main+Sub” (page 97).
, If you have connected an AV amplifier to the
DIGITAL OUT (OPTICAL or COAXIAL) jacks
and want to change the audio track for a DVD-
RW (VR mode) during playback, set “Dolby
Digital” in Audio Setup to “D-PCM” (page 92).
Playback
The recorder does not play any type of disc
(except HDD).
, The disc is upside down. Insert the disc with the
labelled side facing up.
, The disc is not correctly inserted.
, Moisture has condensed inside the recorder.
Remove the disc and leave the recorder turned on
for about half an hour until the moisture
evaporates.
, If the disc was recorded on another recorder, the
recorder cannot play the disc if it was not
finalized (page 37).
101
Additional Information
The recorder does not start playback from the
beginning.
, Resume play was activated (page 54).
, You have inserted a DVD whose Title menu or
DVD menu automatically appears on the TV
screen when it is first inserted. Use the menu to
start playback.
The recorder starts playing automatically.
, The DVD VIDEO features an auto playback
function.
Playback stops automatically.
, If the DVD has an auto pause signal, the recorder
stops playback at the auto pause signal.
Some functions such as Stop, Search, or Slow-
motion Play cannot be performed.
, Depending on the DVD, you may not be able to
do some of the operations above. See the
instruction manual supplied with the disc.
The language for the sound track cannot be
changed.
, Multilingual tracks are not recorded on the DVD
being played.
, The DVD VIDEO prohibits the changing of the
language for the sound track.
, Try changing the language using the DVD
VIDEO’s menu.
The subtitle language cannot be changed or
turned off.
, Multilingual subtitles are not recorded on the
DVD VIDEO.
, The DVD VIDEO prohibits changing of the
subtitles.
, Try changing the subtitle using the DVD
VIDEO’s menu.
, The subtitles cannot be changed for the titles
recorded on this recorder.
The angles cannot be changed.
, Multi-angles are not recorded on the DVD
VIDEO being played.
, You are trying to change the angles when “
does not appear on the TV screen (page 56).
, The DVD VIDEO prohibits changing angles.
, Try changing the angle using the DVD VIDEO’s
menu.
, The angles cannot be changed for the titles
recorded on this recorder.
The MP3 audio tracks do not play.
, The MP3 audio tracks are not recorded in a
format that the recorder can play (page 62).
Recording/Timer recording/Editing
The programme position cannot be changed
from the channel you are recording.
, Set the TV’s input source to “TV.”
Recording does not start immediately after you
press z REC.
, Operate the recorder only after “LOAD,”
“FORMAT,” or “INFOWRITE” disappears
from the front panel display.
Nothing was recorded even though you set the
timer setting correctly.
, There was a power failure during recording.
, The recorder’s internal clock stopped due to a
power failure that lasted for more than 1 hour.
Reset the clock (page 87).
, The channel was disabled after the timer
recording was set. See “Channel Setting” on
page 84.
, Disconnect the mains lead from the mains, and
connect it again.
, “PDC/VPS Scan Off” was selected in the
TOOLS menu (page 43).
, The programme contains copy protection signals
that restrict copying.
, Other timer setting overlapped the timer setting
(page 47).
, There is no DVD inside the recorder.
, There is not enough disc space for the recording.
, The recorder was in the process of DV Dubbing.
Recording does not stop immediately after you
press x REC STOP.
, It will take a few seconds for the recorder to input
disc data before recording can stop.
Recording does not stop after you press x
STOP.
, Open the remote’s cover and press x REC
STOP.
,continued
102
Timer recording is not complete or did not start
from the beginning.
, There was a power failure during recording. If
the power recovers when there is a timer
recording, the recorder resumes recording.
Should the power failure continue for more than
1 hour, reset the clock (page 87).
, Other timer setting overlapped the timer setting
(page 47).
, Disc space was not enough.
, The PDC/VPS function is working.
Contents previously recorded were erased.
, Data that has been recorded on a DVD with a PC
will be erased from the disc when the disc is
inserted.
, “Auto Title Erase” in the TOOLS menu (appears
when you press TOOLS while the Timer List
menu is turned on) is set to “On” (page 47).
, The title was updated and recorded over
(page 42).
The PDC/VPS function does not operate.
, Check that the clock and date are set correctly.
, Check that the PDC/VPS time you set is the
correct one (there might be a mistake in the TV
programme guide). If the broadcast you wanted
to record did not send the good PDC/VPS
information, the recorder will not start recording.
, If the reception is poor, the PDC/VPS signal
might be altered and the recorder might not start
recording.
, “PDC/VPS Scan Off” is selected (page 43).
Recording from the equipment with
a timer
Nothing was recorded even though you set the
Synchro-Rec setting correctly.
, You forgot to turn off the connected equipment.
Turn off the connected equipment and set the
recorder to Synchro-Rec standby mode
(page 51).
, The recorder was not set to the Synchro-
Recording standby mode. Press SYNCHRO
REC to have the recorder stand by for recording.
Make sure the SYNCHRO REC indicator lights
up on the front panel (page 51).
, The recorder is connected to the TV output jack
of the connected equipment.
Synchro-Recording does not complete.
, The timer setting for the connected equipment
overlapped the recorder’s timer setting
(page 52).
, There was a power failure during the recording.
The recorder automatically starts recording
when the satellite receiver is turned on.
, The Synchro-Rec function was activated. Turn
off the satellite receiver and cancel the Synchro-
Rec function (page 51).
Display
The clock has stopped.
, Set the clock again (page 87).
, The clock stopped due to a power failure that
lasted for more than 1 hour. Reset the clock
(page 87).
The TIMER REC indicator is flashing.
, The disc does not have enough space.
, Insert a recordable disc inside the recorder.
The recording mode indication is incorrect.
, When the recording or dubbing is less than three
minutes, the recording mode indication may be
displayed incorrectly. The actual recording itself
is correctly made in the selected recording mode.
The clock does not appear in the front panel
display.
, “Dimmer” in Options Setup is set to “Power
Save” (page 97).
Remote control
The remote does not function.
, Batteries are weak.
, The remote is too far from the recorder.
, The remote’s manufacturer code returned to the
default setting when you replaced the batteries.
Reset the code (page 20).
, Turn on the recorder.
, The remote is not pointed at the remote sensor on
the recorder.
, Different command modes are set for the
recorder and remote. Set the same command
mode (page 21).
, Set the TV/DVD switch to DVD (page 21).
103
Additional Information
Other Sony equipment responds to the remote.
, The same command mode is set for both the
equipment and recorder. Set a different
command mode for the recorder (page 21).
Others
The recorder does not operate properly.
, Restart the recorder. Press down [/1 on the
recorder for more than ten seconds until
“WELCOME” appears in the front panel display.
, When static electricity, etc., causes the recorder
to operate abnormally, turn off the recorder and
wait until the clock appears in the front panel
display. Then, unplug the recorder and after
leaving it off for a while, plug it in again.
Five numbers or letters are displayed in the
front panel display.
, The self-diagnosis function was activated (see
the table on page 104).
The disc tray does not open after you press Z
(open/close).
, It may take a few seconds for the disc tray to
open after you have recorded or edited a DVD.
This is because the recorder is adding disc data to
the disc.
The disc tray does not open and “TRAY
LOCKED” appears in the front panel display.
, Contact your Sony dealer or local authorized
Sony service facility.
“RECOVERY” appears in the front panel
display.
, The recorder’s recovery function was activated
when the recorder was turned on because the
power was turned off or failed during recording.
Leave the recorder on until “RECOVERY”
disappears from the front panel display.
“HDD ERROR” appears in the front panel
display.
, The hard disk error occurred. Press down @/1 on
the recorder for ten seconds to restart the
recorder. If this does not resolve the problem,
format the recorder’s HDD by pressing down the
HDD button on the recorder for more than ten
seconds until “WELCOME” appears in the front
panel display. Note that all the contents recorded
on the HDD will be erased.
“FAN ERROR” appears in the front panel
display.
, Check that the vent on the rear of the recorder is
not blocked. Then, turn off the recorder, wait
until the clock appears in the front panel display,
and disconnect the mains lead. Leave the
recorder off for a while, then re-connect the
mains lead, and press [/1 on the recorder.
Mechanical sound is heard when the recorder
is off.
, While the recorder is adjusting the clock for the
Auto Clock Set function or scanning the
channels for the PDC/VPS function, operational
noises (such as the internal fan) may be heard,
even when the power is off. This is not a
malfunction.
The disc tray does not open and you cannot
remove the disc after you press Z (open/
close).
, Turn off the recorder. Once the clock appears in
the front panel display, disconnect the mains
lead. Connect it again while pressing down A on
the recorder, and release the button when the disc
tray opens. Then, keep [/
1 on the recorder
pressed for about ten seconds until
“WELCOME” appears in the front panel display.
“LOCKED” appears in the front panel display.
, The disc tray is locked. Cancel the Child Lock
(page 55).
104
Self-diagnosis Function
(When letters/numbers
appear in the display)
When the self-diagnosis function is activated to
prevent the recorder from malfunctioning, a five-
character service number (e.g., C 13 50) with a
combination of a letter and four numbers appears
in the front panel display. In this case, check the
following table.
Notes About This Recorder
On operation
If the recorder is brought directly from a cold to
a warm location, or is placed in a very damp
room, moisture may condense on the lenses
inside the recorder. Should this occur, the
recorder may not operate properly. In this case,
remove the disc and leave the recorder turned on
for about half an hour until the moisture
evaporates.
When you move the recorder, take out any discs.
If you don’t, the disc may be damaged.
On adjusting volume
Do not turn up the volume while listening to a
section with very low level inputs or no audio
signals. If you do, the speakers may be damaged
when a peak level section is played.
On cleaning
Clean the cabinet, panel, and controls with a soft
cloth slightly moistened with a mild detergent
solution. Do not use any type of abrasive pad,
scouring powder or solvent such as alcohol or
benzine.
About repairing the hard disk drive
It may be necessary to access data stored on the
hard disk for testing purposes; there is no
intention to copy or store the data, titles or any
other information.
If replacement or initialization (format) is
required, the hard disk will be formatted at our
discretion. In this case, please note that all of the
contents recorded there will be erased (including
any data found to violate copyright law).
On cleaning discs
Do not use a commercially available cleaning
disc. It may cause a malfunction.
Notes about the discs
To keep the disc clean, handle the disc by its
edge. Do not touch the surface. Dust,
fingerprints, or scratches on the disc may cause
it to malfunction.
First three
characters of the
service number
Cause and/or
corrective action
C 13 The DVD is dirty.
, Clean the disc with a
soft cloth.
C 31 The DVD/CD is not
inserted correctly.
, Re-insert the disc
correctly.
E XX
(xx is a number)
To prevent a malfunction,
the recorder has
performed the self-
diagnosis function.
, Contact your nearest
Sony dealer or local
authorized Sony
service facility and
give the five-
character service
number.
Example: E 61 10
105
Additional Information
Do not expose the disc to direct sunlight or heat
sources such as hot air ducts, or leave it in a car
parked in direct sunlight as the temperature may
rise considerably inside the car.
After playing, store the disc in its case.
Clean the disc with a cleaning cloth. Wipe the
disc from the centre out.
Do not use solvents such as benzine, thinner,
commercially available cleaners, or anti-static
spray intended for vinyl LPs.
Do not use the following discs.
A disc that has a non-standard shape (e.g.,
card, heart).
A disc with a label or sticker on it.
A disc that has cellophane tape or sticker
adhesive on it.
Specifications
System
Laser: Semiconductor laser
Channel coverage:
PAL/SECAM (B/G, D/K, I, L)
VHF: E2 to E12, R1 to R12, F1 to F10, Italian
A to H, Ireland A to J, South Africa 4 to 13/
UHF: E21 to E69, R21 to R69, B21 to B69,
F21 to F69/CATV: S01 to S05, S1 to S20,
France B to Q/HYPER: S21 to S41
The above channel coverage merely ensures the
channel reception within these ranges. It does not
guarantee the ability to receive signals in all
circumstances.
Video reception: Frequency synthesizer system
Audio reception: Split carrier system
Aerial out: 75-ohm asymmetrical aerial socket
Timer: Clock: Quartz locked/Timer indication:
24-hour cycle (digital)/Power back-up
duration: 1 hour
Video recording format: MPEG Video
Audio recording format/applicable bit rate:
Dolby Digital/2 ch, 256 kbps
When you play PCM sound tracks with a 96 kHz
sampling frequency, the output signals from the
DIGITAL OUT (OPTICAL or COAXIAL) jack
are converted to 48 kHz sampling frequency.
Inputs and outputs
LINE 2 OUT
(AUDIO): Phono jack/2 Vrms/10 kilohms
(VIDEO): Phono jack/1.0 Vp-p
(S VIDEO): 4-pin mini DIN/Y:1.0 Vp-p, C: 0.3
Vp-p (PAL)
LINE 2 IN/LINE 4 IN
(AUDIO): Phono jack/2 Vrms/more than 22
kilohms
(VIDEO): Phono jack/1.0 Vp-p
(S VIDEO): 4-pin mini DIN/Y:1.0 Vp-p, C: 0.3
Vp-p (PAL)
,continued
106
LINE 1 -TV: 21-pin
CVBS IN/OUT
S-Video/RGB OUT (upstream)
LINE 3/DECODER: 21-pin
CVBS IN/OUT
S-Video/RGB IN
S-Video OUT (downstream)
Decoder
DV IN: 4-pin/i.LINK S100
DIGITAL OUT (OPTICAL): Optical output
jack/–18 dBm (wave length: 660 nm)
DIGITAL OUT (COAXIAL): Phono jack/0.5
Vp-p/75 ohms
COMPONENT VIDEO OUT
(Y, P
B/CB, PR/CR):
Phono jack/Y: 1.0 Vp-p, PB/CB: 0.7 Vp-p,
P
R/CR: 0.7 Vp-p
General
Power requirements: 220-240 V AC, 50/60 Hz
Power consumption:
RDR-HX900: 54 W
RDR-HX1000: 55 W
Dimensions (approx.): 430 × 89 × 346 mm
(width/height/depth) incl. projecting parts
Hard disk drive capacity:
RDR-HX900: 160 GB
RDR-HX1000: 250 GB
Mass (approx.): 5.9 kg
Operating temperature: 5 ºC to 35 ºC
Operating humidity: 25 % to 80 %
Supplied accessories:
Audio/video cord (1)
Mains lead (1)
Aerial cable (1)
Remote commander (remote) (1)
R6 (size AA) batteries (2)
Specifications and design are subject to change
without notice.
Compatible colour systems
This recorder is designed to record using the PAL
colour system and play back using the PAL or
NTSC colour systems.
The signals of the SECAM colour system can be
received or recorded but played back in the PAL
colour system only. Recording of video sources
based on other colour systems cannot be
guaranteed.
About i.LINK
The DV IN jack on this recorder is an i.LINK-
compliant DV IN jack. This section describes the
i.LINK standard and its features.
What is i.LINK?
i.LINK is a digital serial interface for handling
digital video, digital audio and other data in two
directions between equipment having the i.LINK
jack, and for controlling other equipment.
i.LINK-compatible equipment can be connected
by a single i.LINK cable. Possible applications are
operations and data transactions with various
digital AV equipment. When two or more i.LINK-
compatible equipment are connected to this
recorder in a daisy chain, operations and data
transactions are possible with not only the
equipment that this recorder is connected to but
also with other devices via the directly connected
equipment.
Note, however, that the method of operation
sometimes varies according to the characteristics
and specifications of the equipment to be
connected, and that operations and data
transactions are sometimes not possible on some
connected equipment.
Note
Normally, only one piece of equipment can be connected
to this recorder by the i.LINK cable (DV connecting
cable). When connecting this recorder to i.LINK-
compatible equipment having two or more i.LINK jacks
(DV jacks), see the instruction manual of the equipment
to be connected.
About the name “i.LINK”
i.LINK is a more familiar term for IEEE 1394 data
transport bus proposed by SONY, and is a
trademark approved by many corporations.
IEEE 1394 is an international standard
standardized by the Institute of Electrical and
Electronics Engineers.
107
Additional Information
i.LINK baud rate
i.LINK’s maximum baud rate varies according to
the equipment. Three maximum baud rates are
defined:
S100 (approx. 100 Mbps*)
S200 (approx. 200 Mbps)
S400 (approx. 400 Mbps)
The baud rate is listed under “Specifications” in
the instruction manual of each equipment. It is
also indicated near the i.LINK jack on some
equipment.
The maximum baud rate of equipment on which it
is not indicated such as this unit is “S100.”
When units are connected to equipment having a
different maximum baud rate, the baud rate
sometimes differs from the indicated baud rate.
* What is Mbps?
Mbps stands for megabits per second, or the amount of
data that can be sent or received in one second. For
example, a baud rate of 100 Mbps means that 100
megabits of data can be sent in one second.
i.LINK functions on this recorder
For details on how to dub when this recorder is
connected to other video equipment having DV
jacks, see page 77.
The DV jack on this recorder can only input DVC-
SD signals. It cannot output signals. The DV jack
will not accept MICRO MV signals from
equipment such as a MICRO MV digital video
camera with an i.LINK jack.
For further precautions, see the notes on page 77.
For details on precautions when connecting this
recorder, also see the instruction manuals for the
equipment to be connected.
Required i.LINK cable
Use the Sony i.LINK 4-pin-to-4-pin cable (during
DV dubbing).
i.LINK and are trademarks.
108
Guide to Parts and Controls
For more information, see the pages in parentheses.
Front panel
Buttons on the recorder have the same function as the buttons on the remote if they have the same or
similar names.
A @/1 (on/standby) button (22)
B Front panel display (39, 110)
C Disc tray (42)
D TIMER REC indicator (42)
SYNCHRO REC indicator (51)
E (remote sensor) (19)
F A (open/close) button (42)
G H (play) button (54)
X (pause) button (56)
x (stop) button (54)
H z REC button (48)
X REC PAUSE button (48)
x REC STOP button (48)
I </M/m/,/ENTER button (22)
J SYSTEM MENU button (32)
TOOLS button (33)
K O RETURN button (33)
L ./> (previous/next) buttons (56)
M PROGRAM +/– buttons (48)
N REC MODE button (41)
O INPUT SELECT button (52, 77)
P DVD button/indicator (33)
HDD button/indicator (33)
Q LINE 2 IN (S VIDEO/VIDEO/AUDIO L/
R) jacks (27)
qk DV IN jack (77)
109
Additional Information
Remote
Buttons on the remote have the same function as
the buttons on the recorder if they have the same
or similar names. Buttons with an orange dot next
to them can be used with your TV when the TV/
DVD switch is set to TV.
A TV/DVD switch (20)
B Z (open/close) button (42, 56)
C HDD button (33)
DVD button (33)
D Number buttons (44, 61)
SET button (44)
The number 5 button has a tactile dot*.
E CLEAR/-/-- (ten digit) button (44)
F (audio) button (56)
(subtitle) button (56)
(angle) button (56)
G [TIMER] button (42, 44)
H SYSTEM MENU button (32)
TITLE LIST button (33, 54, 65)
TOOLS button (33)
I CURSOR MODE button (33)
J O RETURN button (33)
K TOP MENU button (54)
L . (previous)/> (next)
buttons (56)
M z REC button (48)
X REC PAUSE button (48)
x REC STOP button (48)
N REC MODE button (41)
O SYNCHRO REC button (51)
P PROGRESSIVE button (16)
Q ONE TOUCH DUBBING button (79)
R [/1 (on/standby) button (22)
S PROG (programme) +/– buttons (48)
The + button has a tactile dot*.
T 2 (volume) +/– buttons (20)
U t (TV/video), TV/DVD button (20)
V DISPLAY button
(38)
TIME/TEXT button (38)
W (wide mode) button (20)
X </M/m/,/ENTER button (22)
Y ZOOM +/– buttons (33)
Z (instant replay)/ (instant advance)
buttons (56)
1 2 3
4 5 6
7 8 9
0
,continued
110
wj MENU button (54)
wk m / M (search) buttons (56)
wl H (play) button (54)
The button has a tactile dot*.
X (pause) button (56)
x (stop) button (54)
e; CHAPTER MARK/ERASE buttons (68)
ea INPUT SELECT button (52, 77)
es SUR (surround) button (56)
ed COMMAND MODE switch (DVD 1,2,3)
(21)
* Use the tactile dot as a reference when operating the
recorder.
Front panel display
A HDD/DVD indicators
Displays the selected media and the
playing/recording/dubbing status.
B Disc type*/recording format
C (angle) indicator (56)
D PLAYLIST indicator (34)
E Audio signal indicators (38)
F STEREO/BILINGUAL indicators (41)
G NICAM indicator (41)
H TV indicator (48)
I Displays the following (39):
Playing time/remaining time
Current title/chapter/track/index number
Recording time/recording mode
•Clock
Programme position
TV Direct Rec indication
(48): “TV”
appears in the right most two digits.
J SMARTLINK indicator (15)
K PROGRESSIVE indicator (16)
* Displays DATA CDs as “CD.”
z Hint
You can turn off the front panel display when the recorder is turned off by setting “Dimmer” to “Power Save” in Options
Setup (page 97).
HDD DVD
DVD RW
PLAYLIST
VCDVR
STEREO
BILINGUAL
NICAM
TV
PROGRESSIVE
SMARTLINK
111
Additional Information
Rear panel
A AERIAL IN/OUT jacks (13)
B LINE 1 – TV jack (14)
C LINE 3/DECODER jack (26)
D COMPONENT VIDEO OUT (Y, P
B/CB,
P
R/CR) jacks (14)
E AC IN terminal (19)
F LINE 2 OUT (S VIDEO) jack (14)
G LINE 2 OUT (AUDIO L/R/VIDEO) jacks
(14, 17)
H DIGITAL OUT (COAXIAL/OPTICAL)
jacks (17)
I LINE 4 IN (S VIDEO) jack (27)
J LINE 4 IN (AUDIO L/R/VIDEO) jacks
(27)
AERIAL
IN
LINE 4 IN DIGITAL OUT
COAXIAL
OPTICAL
PCM/DTS/MPEG/
DOLBY DIGITAL
COMPONENT
VIDEO OUT
VIDEO
S VIDEO
AUDIOR L
LINE 2 OUT
VIDEO
S VIDEO
AUDIOR L
Y
P
B
/
C
B
P
R
/
C
R
~ AC IN
OUT
LINE 1 - TV LINE 3 / DECODER
112
Glossary
Chapter (page 61)
Sections of a picture or a music feature that are
smaller than titles. A title is composed of several
chapters. Depending on the disc, no chapters may
be recorded.
Copy protection signals (page 42)
Copy restriction set by copyright owners, etc.
These signals are included in some software or TV
programmes and restrict recording on this
recorder.
Dolby Digital (page 92)
Digital audio compression technology developed
by Dolby Laboratories. This technology conforms
to multi-channel surround sound. The rear channel
is stereo and there is a discrete subwoofer channel
in this format. Dolby Digital provides the same
discrete channels of high quality digital audio
found in “Dolby Digital” theater surround sound
systems.
Good channel separation is realized because all of
the channel data is recorded discretely, and little
deterioration occurs because all channel data
processing is digital.
DTS (page 92)
Digital audio compression technology by Digital
Theater Systems, Inc. This technology conforms
to multi-channel surround sound. The rear channel
is stereo and there is a discrete subwoofer channel
in this format. DTS provides the same discrete
channels of high quality digital audio.
Good channel separation is realized because all of
the channel data is recorded discretely, and little
deterioration occurs because all channel data
processing is digital.
DVD+R (page 8)
A DVD+R (read “plus R”) is a recordable disc that
is the same size as a DVD VIDEO. Contents can
be recorded only once to a DVD+R, and will have
the same format as a DVD VIDEO.
DVD+RW (page 8)
A DVD+RW (read “plus RW”) is a recordable and
rewritable disc. DVD+RWs use a recording
format that is comparable to the DVD VIDEO
format.
DVD-R (page 8)
A DVD-R is a recordable disc that is the same size
as a DVD VIDEO. Contents can be recorded only
once to a DVD-R, and will have the same format
as a DVD VIDEO.
DVD-RW (page 8)
A DVD-RW is a recordable and rewritable disc
that is the same size as a DVD VIDEO. The DVD-
RW has two different modes: VR mode and Video
mode. DVDs created in Video mode have the
same format as a DVD VIDEO, while discs
created in VR (Video Recording) mode allow the
contents to be programmed or edited.
DVD VIDEO (page 8)
A disc that contains up to eight hours of moving
pictures on a disc the same diameter as a CD.
The data capacity of a single-layer and single-
sided DVD is 4.7 GB (Giga Byte), which is 7
times that of a CD. The data capacity of a double-
layer and single-sided DVD is 8.5 GB, a single-
layer and double-sided DVD is 9.4 GB, and
double-layer and double-sided DVD is 17 GB.
The picture data uses the MPEG 2 format, which
is a worldwide standard of digital compression
technology. The picture data is compressed to
about 1/40 (average) of its original size. The DVD
also uses a variable rate coding technology that
changes the data to be allocated according to the
status of the picture. Audio information is
recorded in a multi-channel format, such as Dolby
Digital, allowing you to enjoy a more real audio
presence.
Furthermore, various advanced functions such as
the multi-angle, multilingual, and Parental
Control functions are provided on the DVD.
113
Additional Information
Hard disk drive (page 3)
A hard disk drive is a whole mechanical system
that consists of disks and drive. Disks are flat,
circular, rigid plates coated with a thin magnetic
media. Magnetic heads record data on the rapidly
spinning disks, and this enables the speedy and
efficient reading and writing of data.
Interlace format (page 16)
Interlace format shows every other line of an
image as a single “field” and is the standard
method for displaying images on television. The
even number field shows the even numbered lines
of an image, and the odd numbered field shows the
odd numbered lines of an image.
MPEG Audio (page 92)
International standard coding system used to
compress audio digital signals authorized by ISO/
IEC. MPEG 2, used on DVDs, conforms to up to
7.1-channel surround.
Original (page 64)
Titles actually recorded on a DVD-RW (VR
mode). Erasing original titles frees up disc space.
Playlist (page 64)
Playback information created from the actual
recordings on a DVD-RW (VR mode). A Playlist
leaves the original titles as they are, and contains
only the information needed to control playback.
A Playlist title takes up very little disc space.
Progressive format (page 16)
Compared to the Interlace format that alternately
shows every other line of an image (field) to create
one frame, the Progressive format shows the entire
image at once as a single frame. This means that
while the Interlace format can show 25-30 frames/
50-60 fields in one second, the Progressive format
can show 50/60 frames in one second. The overall
picture quality increases and still images, text, and
horizontal lines appear sharper.
Title (page 61)
The longest section of a picture or music feature
on a DVD, movie, etc., in video software, or the
entire album in audio software.
Track (page 61)
Sections of a music feature on a CD (the length of
a song).
114
Language Code List
For details, see page 88.
The language spellings conform to the ISO 639: 1988 (E/F) standard.
Code Language Code Language Code Language Code Language
1027 Afar
1028 Abkhazian
1032 Afrikaans
1039 Amharic
1044 Arabic
1045 Assamese
1051 Aymara
1052 Azerbaijani
1053 Bashkir
1057 Byelorussian
1059 Bulgarian
1060 Bihari
1061 Bislama
1066 Bengali;
Bangla
1067 Tibetan
1070 Breton
1079 Catalan
1093 Corsican
1097 Czech
1103 Welsh
1105 Danish
1109 German
1130 Bhutani
1142 Greek
1144 English
1145 Esperanto
1149 Spanish
1150 Estonian
1151 Basque
1157 Persian
1165 Finnish
1166 Fiji
1171 Faroese
1174 French
1181 Frisian
1183 Irish
1186 Scots Gaelic
1194 Galician
1196 Guarani
1203 Gujarati
1209 Hausa
1217 Hindi
1226 Croatian
1229 Hungarian
1233 Armenian
1235 Interlingua
1239 Interlingue
1245 Inupiak
1248 Indonesian
1253 Icelandic
1254 Italian
1257 Hebrew
1261 Japanese
1269 Yiddish
1283 Javanese
1287 Georgian
1297 Kazakh
1298 Greenlandic
1299 Cambodian
1300 Kannada
1301 Korean
1305 Kashmiri
1307 Kurdish
1311 Kirghiz
1313 Latin
1326 Lingala
1327 Laothian
1332 Lithuanian
1334 Latvian;
Lettish
1345 Malagasy
1347 Maori
1349 Macedonian
1350 Malayalam
1352 Mongolian
1353 Moldavian
1356 Marathi
1357 Malay
1358 Maltese
1363 Burmese
1365 Nauru
1369 Nepali
1376 Dutch
1379 Norwegian
1393 Occitan
1403 (Afan)Oromo
1408 Oriya
1417 Punjabi
1428 Polish
1435 Pashto;
Pushto
1436 Portuguese
1463 Quechua
1481 Rhaeto-
Romance
1482 Kirundi
1483 Romanian
1489 Russian
1491 Kinyarwanda
1495 Sanskrit
1498 Sindhi
1501 Sangho
1502 Serbo-
Croatian
1503 Singhalese
1505 Slovak
1506 Slovenian
1507 Samoan
1508 Shona
1509 Somali
1511 Albanian
1512 Serbian
1513 Siswati
1514 Sesotho
1515 Sundanese
1516 Swedish
1517 Swahili
1521 Tamil
1525 Telugu
1527 Tajik
1528 Thai
1529 Tigrinya
1531 Turkmen
1532 Tagalog
1534 Setswana
1535 Tonga
1538 Turkish
1539 Tsonga
1540 Tatar
1543 Twi
1557 Ukrainian
1564 Urdu
1572 Uzbek
1581 Vietnamese
1587 Volapük
1613 Wolof
1632 Xhosa
1665 Yoruba
1684 Chinese
1697 Zulu
1703 Not specified
115
Index
Words in quotations appear in
the on-screen displays.
Numerics
16:9 24, 88
4:3 Letter Box
24, 88
4:3 Pan Scan
24, 88
A
“A-B Erase” 66
Adjusting
playback picture
58
playback sound
59
recording picture
49
Aerial
13
“AFT”
85
Album
38, 63
Album number
38
“Album Search
61
Angle
56
Area code
95
“Audio”
88
Audio
56, 91
“Audio ATT”
91
“Audio Connection”
24
Audio cord
17
“Audio DRC”
91
“Audio Filter”
59
“Audio Settings”
59
“Auto Adjust”
87
“Auto Chapter”
93
Auto Clock Set
87
“Auto Display”
97
“Auto Title Erase”
47
Auto Tuner Preset
23
B
Batteries 19
“Bilingual”
51, 53
Bilingual recording
41
“BNR”
58
“Brightness”
50, 58
C
“C NR” 58
Canal Plus
29
“Capture”
69
“Capture All”
69
“CATV”
85
CD
10
“Change IN”
70, 81
“Change OUT”
70, 81
“Channel List”
86
“Channel Setting”
84
Chapter
38, 50, 68, 112
CHAPTER ERASE
68
CHAPTER MARK
68
Chapter number
38
“Chapter Search
61
“Chasing Playback”
60
Chasing Playback
60
“Check Overlap”
46
“Check Scenes”
69
Checking/changing/cancel-
ling timer settings (Timer
List)
46
Child Lock
55
Cleaning discs
104
Clock
23, 87
“Colour”
50, 58
“Colour System”
96
Colour systems
106
“Combine”
71
“Command Mode”
22, 97
“Component Out”
89
Component video input
15
COMPONENT VIDEO OUT
14
Connecting
14
the aerial cable
13
the audio cords
17
the video cords
14
“Contrast”
50, 58
Controlling TVs with the re-
mote
20
Copy control signals
42
Copy protection
112
Copy-Free
42
Copy-Never
42
Copy-Once
42
CPRM
8
“Create Playlist”
68
Creating chapters 68
Cursor mode
34
D
DATA CD 10
“Decoder”
30
“Digital Out”
92
Digital video camera
77
“Dimmer
97
“Disc Info”
35
Disc Map
67
“Disc Name
36
Disc settings
35, 96
Disc space
36
Disc types
8
Display
front panel display
39,
110
On-screen display
32
Setup Display
83
“Divide
70
Dolby Digital
18, 24, 92, 112
“Downmix
91
DTS
25, 92, 112
“Dub Mode”
72, 82
Dubbing
72
“Dub Mode”
72
High-speed Dubbing
72
Rec Mode Conversion
Dubbing 73
“Settings”
75
“DV Audio Input”
78
DV Dubbing
77
One Touch Dubbing
79,
96
Program Edit
80
“DV EDIT”
80
DV IN
77
“DVD Bilingual Rec.”
97
“DVD Menu”
88
“DVD Rec. Picture Size”
49
DVD VIDEO
10, 112
DVD+R
8, 112
DVD+RW
8, 112
DVD-R
8, 112
DVD-RW
8, 112
DVD-RWs (Video mode)
64
“DVE”
58
,continued
116
E
Easy Setup 22, 98
Editing
64, 68
DV Edit
77
Enter characters
40
“Erase”
46, 65, 70, 81
“Erase All”
36
“Erase Titles”
66
“Extend Rec”
44
F
“Factory Setup” 97
“Features”
93
“Finalize”
37
“Finalize Disc”
96
Finalizing
37
“Format”
36
“Format DVD”
96
Formatting
36
Freeze Frame
57
Front panel
108
Front panel display
39, 110
G
GB 36
H
Handling discs 104
“HDD Bilingual Rec.”
97
“Hue”
58
I
i.LINK 106
INPUT SELECT
52, 78
Interlace
113
Interlace format
113
L
Labelling 36
Language
88
LINE 2 IN
27
LINE 3/DECODER
26
LINE 4 IN
27
“Line Audio Input”
51, 53
“Line1 Output”
24, 90
“Line3 Input”
90
“Line3 Output”
90
“Line4 Input”
90
M
Mains Lead 19
Manual Clock Set
87
MENU
54
Menu
DVD’s Menu
54
Top menu
54
“Mix”
78
“Modify”
46
“Move
70, 81
MP3 audio tracks
62
MPEG
92, 113
N
NICAM 42, 85
“Normal”
85
Number buttons
40, 45
O
One Touch Dubbing 79, 96
One Touch Menu
55
One Touch Play
55
One Touch Timer
44
On-screen display
“OSD” language
23, 88
Setup Display
83
Sub-menu
32
System Menu
32
TOOLS menu
33
“Options”
96
Original
34, 64, 113
P
Page mode 34
Parental Control
55, 94
Parts and controls
108
“Pause Mode”
89
PAY-TV
29
“PAY-TV/CANAL +”
86
“PB Video Equalizer
58
PBC
54
PDC
43
Picture quality
49, 58
Picture size
49
“Play Beginning”
54
Play mode
38
Playable discs
10
Playback
10, 38, 54, 57
fast forward
57
fast reverse
57
Freeze Frame
56
instant advance
57
instant replay
57
Resume Play
54
Slow-motion play
56
Playing status bar
38
Playlist
34, 64, 68, 113
“Present Time”
87
“Preset Download”
23
“Preview”
70, 81
Program Edit
80
Progressive
16, 113
“Progressive Mode”
89
“Protect
66
“Protect Disc”
36
Protection
disc 36
title
65
Q
Quick guide to disc types 8
Quick Timer
49
R
Rear panel 111
REC
48
“Rec Mode”
49
Rec Mode Adjust
43
“Rec NR”
50
REC PAUSE
48
“Rec Settings”
49
REC STOP
48, 79
“Rec Video Equalizer”
50
Recordable discs
8
Recording
41, 51, 93
picture adjustment
49
recording format
8
Recording mode
41, 50
Recording time
50
“Update”
43
while watching another
programme 48
Recording time
41
RECOVERY
103
Region code
11
Remaining time
38
117
Remote 19, 109
Resetting the recorder
98
Resume Play
54
“RGB”
24, 90
S
S VIDEO 15
“S Video”
24, 90
“Scart Setting”
90
Scene List
69
Screen Saver
89
“Search”
61
Searching
fast reverse/fast forward
57
locating the beginning of
the title/chapter/
track
57
Search mode
61
SET
20, 40
“Set Thumbnail”
66
“Settings”
84
Setup Display
83
Simultaneous Rec and Play
60
Slow-motion play
57
SMARTLINK
15
Sort
34
Sound quality
59
“Station Name”
86
“Stereo1”
78
“Stereo2”
78
Sub-menu
32
Subtitle
56, 88
Super VIDEO CD
10
Surround
57
Synchro Rec
51
“System”
85
System Menu
32, 83
T
Teletext 48, 93
Thumbnail picture
34
“Time Search
61
TIME/TEXT
39
TIMER
43
Timer List
46
Timer recording
check/change/cancel
46
manual setting
42
Rec Mode Adjust
43
Synchro Rec
51
VIDEO Plus+
44
Title
38, 113
TITLE LIST
54
Title List
33, 54
Sort
34
Thumbnail
34
Zoom
33
“Title Name”
66
Title number
38
“Title Search”
61
TOOLS menu
33
TOP MENU
54
Track
113
“Track Search”
61
Troubleshooting
99
Tuner System
23
“TV Direct Rec”
48, 93
“TV Guide Page”
93
TV system
85
“TV Type”
24, 88
TV/DVD
48
TV/DVD switch
20
TVS (TV Virtual Surround)
57
U
“Unfinalize” 37
Usable discs
8, 10
V
“Video” 24, 88, 90
VIDEO CD
10
Video cord
14
Video input
15
Video mode
8
VIDEO Plus+
44
“Video Settings”
58
VPS
43
VR mode
8, 64
Y
“Y NR” 58
Z
Zoom 33
ZWEITON
42
Sony Corporation Printed in Japan
Printed on 100% recycled paper using
VOC (Volatile Organic Compound)-free
vegetable oil based ink.
12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Sony RDRHX900 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Andere Handbücher von Sony RDRHX900

Sony RDRHX900 Bedienungsanleitung - Deutsch - 128 seiten

Sony RDRHX900 Bedienungsanleitung - Holländisch - 120 seiten

Sony RDRHX900 Bedienungsanleitung - Französisch - 128 seiten

Sony RDRHX900 Bedienungsanleitung - Italienisch - 128 seiten

Sony RDRHX900 Bedienungsanleitung - Portugiesisch - 120 seiten

Sony RDRHX900 Bedienungsanleitung - Spanisch - 124 seiten


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info