Bedienungsanleitung Sony rm vl 600 t (Seite 22 von 36) (Englisch)

122744

Zoom out

Zoom in

Vorherige Seite

1/36

Nächste Seite

Example: To programme the procedure above to

the SYSTEM CONTROL B button

1 Press and while holding SET, press the

SYSTEM CONTROL B button.

The SET indicator light turns on.

SET

If a System Control function (System Control

Macro) has already been set on the button,

the SET indicator flashes twice.

The setting procedure is automatically cancelled.

2 Set the System Control function.

With this example, press buttons in sequence as

below:

VCR

AMP

VIDEO1

You can programme up to 16 consecutive steps

on each of the SYSTEM CONTROL buttons (A –

D), including the initial step of pressing switch

to a Component Select button.

3 Press SET to complete the programming.

The SYSTEM CONTROL button light turns off.

To programme a new series of operations for

those buttons which already have a Control

Programme set

Erase the programme (page 22).

Notes

• If you interrupt the procedure at any point for over 20

seconds, the setting mode ends and the series of

commands will be programmed up to that point. In this

case, clear the programme (page 22) and start again from

Step 1 to set the entire programme from the beginning.

You cannot continue programming once the setting mode

ends.

• If a SYSTEM CONTROL button has already “learned” a

remote control signal (page 12), you can programme a

System Control function (System Control Macro), but the

function will not work until you clear the Learning

function. To clear the Learning function, see “Changing

or erasing the function of a “learned” button” on page

16.

• If you change the component code number (page 8) or

programme a new signal by using the Learning function

(page 12) on a key or a button that has been programmed

with a series of commands using the System Control

function, the new signal will be transmitted when you

press the corresponding SYSTEM CONTROL button.

• While in setting mode, you cannot clear any operation

step you have programmed. If you have programmed an

incorrect operation by mistake, start again from Step 1.

• If you try to programme more than 16 steps, the System

Control setting mode ends, and the 16 steps you have

programmed are registered. If you want to programme

the steps again, clear the programme (page 22) and start

again from Step 1.

Tips for programming the System Control

functions

The following information helps you to programme

a consecutive operation steps.

About the order of operation steps

Some of the components may not accept

consecutive remote control signals. For example,

some TVs generally may not respond to the next

signal right after the Power-on signal. So, a series of

commands such as TV Power-on and input select

may not work properly.

In this case, insert other signals to other

components, such as in the example below:

TV Power-ontVCR Power-ont VCR playback t

TV input select

To clear programmed commands

1 Press and while holding SET, press and

hold for more than 3 seconds the SYSTEM

CONTROL button you want to clear.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Sony rm vl 600 t Seite 22

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Sony rm vl 600 t

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info