Bedienungsanleitung Sony rm vl 600 t (Seite 29 von 36) (Englisch)

122744

Zoom out

Zoom in

Vorherige Seite

1/36

Nächste Seite

Symptom

All Component Select buttons flash twice.

After programming the Power-On command of a

component, pressing that Component Select button does

not function correctly.

The System Control function or Control Programme

function does not work properly.

Remedy

• The Hold function is on. Unlock the Hold function (page 25).

•A Learning function has already been set on the Component Select

button. If a Learning function has been set (page 12), you can

programme the Power-On function on the Component Select button

(page 20) but the Power-On setting will not work until you clear the

“learned” function. Erase the “learned” function after setting the

Power-On function.

This function is for Sony components only.

• When you programme a System Control function or Control

Programme function, make sure to follow the correct steps (pages 21,

23).

• Change the direction the Remote Commander is aimed. If the problem

persists, position the programmed components closer together.

• If the remote control receivers of the components are too far apart, or if

something is blocking the signals between them, some of the

components may not operate in sequence even after you press the

programmed button. If some of the components do not operate

correctly because of the above or any other reason, position the

components back to the way they were before you set the System

Control function or Control Programme function. Failure to do this can

result in incorrect operation when you use these functions again.

• Some components may not always be powered on by the System

Control function or Control Programme function. This is because the

power of the component turns on and off alternately when receiving

the power on/off signal. In this case, check the operating component‘s

power on/off state before using the System Control function.

• If you change the AV brands‘ component code number (page 8) set on a

Component Select button that has been programmed for a series of

commands by the Control Programme function, the new signal will be

transmitted when you press the corresponding Component Select

button.

• The intervals between steps may be too short. Depending on the

components, you may need to insert an interval between consecutive

controls. You can insert an interval by changing the order of pressing

the buttons. (You can insert an interval between steps when

programming the Component Select button.)

• If a SYSTEM CONTROL button or a Component Select button has

already “learned” a remote control signal (page 12), you can

programme a System Control function (System Control Macro) or a

Control Programme function (Component Macro), but the function will

not work until you clear the Learned function. To clear the Learned

function, see “Changing or erasing the function of a “learned” button”

on page 16.

Customer Service

If you have any questions or

problems concerning the Remote

Commander that are not covered

in this manual, please call the

customer remote helpline. The

number is mentioned in the

warranty card.

Helpline available

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Sony rm vl 600 t Seite 29

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Sony rm vl 600 t

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info