Bedienungsanleitung Sony rm vl 700 t (Seite 33 von 80) (Deutsch, Englisch)

122521

Zoom out

Zoom in

Vorherige Seite

1/80

Nächste Seite

Troubleshooting

If you have problems setting up or using the Remote Commander, first

check the batteries (page 6), then check the items below.

Remedy

• Go closer to the component. The maximum operating

distance is approximately 10 m (32.8 ft.).

• Check that you are aiming the Commander directly at the

compoent, and that there are no obstructions between the

Commander and the component.

• Power on the components first, if necessary.

• Make sure you have pressed the correct Component Select

button. In case of CBL/SAT, or DVD, make sure the desired

component is selected.

• Check that the component has infrared remote capability. For

example, if your component didn’t come with a remote

commander, it probably isn’t capable of being controlled by a

remote commander.

• You have assigned a different component on the Component

Select button. Check the component assigned to that button

and the component code.

• If your visual components are connected to an audio system,

make sure you’ve set up the Commander as described in

“Controlling the Volume of Visual Components Connected to

an Audio System” (page 24).

• You have assigned another component on the TV or AMP

button (page 27). In this case, the volume cannot be controlled

when you select components other than TV or AMP.

• Set the component code correctly. If the code that is listed first

for your component doesn’t work, try all the codes for your

component in the order in which they are listed in the

supplied “Component Code Numbers”.

• Some features may not be preset. If some or all of the buttons

do not function correctly even after you have set the

component codes, then use the Learning function to

programme the remote control signals for the component

(page 15).

• The component may be operated with a code number that is

not listed in the “Component Code Numbers”. See “Setting a

component code by the Search function” (page 11) and try

setting a code number again with the Search function.

• When you teach signals of an interactive signal exchange

system remote control unit (supplied with some of Sony’s

amplifiers) to the Commander, the response signal of the

main unit may interfere with the learning of the Commander.

In such a case, move to a place where the signals will not

reach the main unit (e.g. other rooms, etc.).

• Make sure that the Remote Commander has “learned” the

correct signals. If not, see “For accurate Learning” (page 18)

and try the Learning procedure again (page 15).

Symptom

You cannot operate the

components.

You cannot control the

volume.

You cannot operate the

components even after

setting the component

code numbers.

The Commander fails to

learn the remote control

signals.

You cannot operate a

component even after

you programmed the

remote control signals

with the Learning

function.

Continued

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Sony rm vl 700 t Seite 33

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Sony rm vl 700 t

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info