Bedienungsanleitung Sony RMVL1400T.CE7 (Seite 19 von 96) (Englisch)

67640

Zoom out

Zoom in

Vorherige Seite

1/96

Nächste Seite

Continued

5 Press the DVD button, the

press the 1 (power) button.

6 Press the OTHER button

repeatedly, press the Label

select button corresponding to

the amplifier, then press the 1

(power) button.

7 Press the t (input select)

button repeatedly to select the

appropriate video input on the

TV to watch the DVD.

8 Press the input select button

on the amplifier to select the

appropriate audio input to

watch the DVD.

9 Press the DVD button, then

press N.

Press the (light) button.

A beep sounds and programming is

complete.

Press the (light) button or

the RETURN button twice.

The set mode closes, and the Remote

Commander returns to standby for

operating the A/V components.

Notes

• If the procedure is interrupted at any point for

over 60 seconds, programming is cancelled.

You cannot continue from where you left off.

• If you try to programme actions on a button

that already has a programmed Component

Macro, a beep sounds twice to alert you that

you cannot programme a Component Macro

on the button. In such a case, clear the

programmed Component Macro (page 20),

then start programming again from step 1.

•You cannot clear steps during the

programming procedure. If you make a

mistake in programming actions, finish

programming once and clear the Component

Macro (page 20), then start again from step 1.

•You can programme up to 32 consecutive

operation actions. When up to 32 steps are

programmed, programming of the Component

Macro is full. To change the programmed

steps, clear the Component Macro (page 20),

then start over from step 1.

Checking if a Component

Macro is executed properly

Follow the procedure below to check if

the programmed Component Macro

works as intended.

To execute a Component

Macro

1 Press and hold the

COMPONENT select button

on which the desired

Component Macro has been

programmed for over 2

seconds.

The signal transmission icon appears

on the screen, and the programmed

Component Macro is executed.

Tip

While the signal transmission icon ( )

appears and the Component Macro is executed,

“CANCEL” appears in the third line of the

screen. You can cancel executing the

Component Macro by pressing the right Label

select button.

To check the programmed

steps of a Component Macro

and add a delay action

Delay action allows you to set an interval

between steps. Delay time is set to 250

ms. (1/4 second) on the Remote

Commander.

If a Component Macro is not executed as

intended, check the programmed steps

and try adding a delay to execute the

programme properly.

1 While pressing the (light)

button, press the OTHER

button.

“SET MODE” appears as the screen

title.

2 Press the V/v buttons to

select “4 MACRO”, then press

the OK button or the centre

Label select button.

“MACRO” appears as the screen title.

Tip

If a number is displayed before the menu,

you can select the menu by pressing the

number button.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Sony RMVL1400T.CE7 Seite 19

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Sony RMVL1400T.CE7

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info