Bedienungsanleitung Sony RMVL1400T.CE7 (Seite 32 von 96) (Englisch)

67640

Zoom out

Zoom in

Vorherige Seite

1/96

Nächste Seite

Problem

You cannot operate a component

even after you programmed the

remote control signals with the

“learning” function.

“NG” appears in the third line on

the screen and a beep sounds five

times while setting the preset

code.

“NG” appears in the third line on

the screen and a beep sounds five

times while learning.

“FULL” appears in the third line

on the screen and a beep sounds

five times while learning.

“NG” appears in the third line on

the screen and a beep sounds five

times when trying to copy settings

of a component label to another

component label.

A beep sounds twice while setting

the preset code.

A beep sounds twice while

learning.

A beep sounds twice while

programming a Component

Macro.

“NG” appears in the third line on

the screen and a beep sounds

twice while programming the

power-on function.

Solution

Make sure that the Remote Commander has learned the

correct signals. If not, see “Notes” on page 13 or “For

accurate learning” (page 14), and try the learning

procedure again (page 12).

Preset code setting has not succeeded. Set the preset code

again, referring to the supplied “Preset Code List”.

• Learning has not succeeded. Try the learning procedure

again (page 12), referring to “For accurate learning”

(page 14).

• While learning, you pressed the button other than the one

on which you want to programme the signal. Programme

the signal on the correct button again (page 12).

Learned signal memory is full. Clear learned signals that

are not frequently used (page 14), then programme the

desired remote signal.

• Setting cannot be copied on COMPONENT select

buttons or Label select buttons in the following

situations:

– A learned signal or Component Macro is programmed.

– The button’s component label has been changed.

– The button’s function label has been changed.

In this case, reset those settings (page 28) before copying.

• You are copying the settings of A/V components other

than a TV or amplifier on the Label select button

assigned with a TV or amplifier. The TV button is

assigned with only TV and the Label select button to

which an amplifier is preset is assigned with only

amplifier or DVD player home theatre system.

• The Remote Commander fails to copy the settings if the

programmed signal data of the button is too large. In this

case, clear programmed signals that are not frequently

used (page 14), then copy the settings again.

The preset code cannot be set on the COMPONENT select

button or Label select button in the following situations:

– A learned signal or Component Macro is programmed.

– The button’s component label has been changed.

– The button’s function label has been changed.

In this case, reset those settings (page 28) before setting.

• See “For accurate learning” (page 14).

• Other remote signal has been programmed on the desired

button. Clear the learned signal (page 14) or programme

the remote signal on another button (page 12).

• Learning standby time (10 seconds) has been exceeded.

Start over from the beginning.

• You are assigning a Component Macro on the

COMPONENT select button or Label select button on

which another Component Macro has been assigned.

Clear the Component Macro assigned to the button (page

20), then assign the desired Component Macro.

• The programmed steps exceed 32 after adding delay

while checking the Component Macro. A maximum of 32

steps (including delay) can be programmed.

Reprogramme the Component Macro.

You are programming the power-on function (page 21) on

the COMPONENT select button or Label select button

assigned with a preset code other than Sony’s. The power-

on function can be programmed only on the button

assigned with Sony’s preset code.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Sony RMVL1400T.CE7 Seite 32

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Sony RMVL1400T.CE7

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info