Bedienungsanleitung Sony SNC-EP520 (Seite 32 von 99) (Englisch)

699842

Zoom out

Zoom in

Vorherige Seite

1/99

Nächste Seite

SNC EP520/EP521/EP550/EP580/ER520/ER521/ER550/ER580/ER585/ER585H/ZP550/ZR550

Administrating the Camera

Configuring the System — System Menu

Installation Tab

You can perform settings related to installation.

Display sample: SNC-EP550/ER550

Camera operating mode (SNC-EP550/

EP580/ER550/ER580/ER585/ER585H/

ZP550/ZR550)

You can switch the operating modes of the camera.

Select either 25 fps or 30 fps.

The settings of the camera operating mode are related to

the frame rate selected in the Video code tab.

When the camera operating mode is switched, the

message “This System will be rebooted. Are you sure?”

appears.

Click OK to reboot the camera, and complete the

settings.

HPoE LLDP function

Based on 802.3at, select whether to use the power

adjustment function by LLDP (Link-Layer-Discovery-

Protocol).

Select ON in the case of IEEE802.3at compatible power

adjustment by PSE (Power Sourcing Equipment).

Notes

• Before setting, check the specifications, power level

and settings of the PSE you are going to connect.

• If the PSE with which you will use this unit cannot

supply sufficient power and you set the HPoE LLDP

function to Off, the unit may not operate correctly.

• The HPoE LLDP function may be slow to start if the

LLDP function is set to ON and PSE is not used for

some LLDP functions.

Eflip

You can display flip vertical images on the computer.

Select Off when you hang the camera from a ceiling.

Select On when you install the camera on a rack, etc.

Note

Panorama images, thumbnails set in the Preset Setting

menu, privacy mask positions and motion detection

areas, etc., will not be inverted, even if the On/Off

setting of the inverted image is switched. To invert the

image, make the setting again.

Video out (SNC-ZP550/ZR550)

Set the video output from the BNC cable connected to

the SLOC port. When outputting video images, select

On.

Notes

• The format for video output signals varies depending

on the Camera operating mode setting. In Camera

operating mode, 30 fps is for NTSC and 25 fps is for

PAL.

• When Video out is set to On, the motion detection

function and Image 2 of Video codec will not be

available.

Stabilizer (SNC-EP520/EP521/ER520/

ER521/ER585/ER585H)

Set Stabilizer. When you select On, the camera image

vibration will be reduced on the place where this unit is

installed with vibration.

Notes

• When Stabilizer is set to On, the shooting angle of

view will be narrowed by 20%.

Using preset or cropping functions (SNC-ER585/

ER585H) will also narrow the shooting angle of view.

• If Stabilizer is set to On, the compensation will not be

effective depending on vibration.

• It will take some time before the effect of the

compensation appears after operating the camera’s

pan, tilt or zoom functions.

• Since the SNC-ER585/ER585H models integrate the

rolling shutter and CMOS sensor, focal-plane shutter

effects may occur when using the stabilizer function.

OK/Cancel

See “Buttons common to every menu” on page 26.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Sony SNC-EP520 Seite 32

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Sony SNC-EP520

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info