Bedienungsanleitung Sony SNC-WR602 (Seite 52 von 73) (Englisch)

699857

Zoom out

Zoom in

Vorherige Seite

1/73

Nächste Seite

Administrating the Camera

Setting the Sensor input/Camera tampering detection/Motion detection — Action input Menu

Sensor input Tab — Set the sensor

input 1/2/3/4

Sensor input mode

Set the direction of the detected input signal to the

sensor input terminal of the camera.

Normally open: Triggers an alarm when the sensor

input is short-circuited.

Normally closed: Triggers an alarm when the sensor

input is open-circuited.

Notes

• Allow at least two seconds for the input signal to be

detected; otherwise, some events may not be detected.

• When you use video streaming by SSL connection, set

as follows. Some events may not be detected if the

camera is not in the following conditions.

–Set the Bit rate below 1 Mbps.

–Set the Frame rate below 30 fps.

– Use the video streaming below two transmissions at

the same time.

OK/Cancel

See “Buttons common to every menu” on page 21.

Camera tampering detection Tab —

Set the camera tampering detection

Note

Deselect the checkbox of Stabilizer in the Installation

tab of the System menu. After setting the camera

tampering detection, set the Stabilizer function again.

Enable

Select the checkbox to activate the function to detect

camera tampering, such as direction shifting or spray.

Detection status

Display the tampering detection state of the time when

Camera tampering detection tab is opened. To clear the

detection status, click Clear button.

Auto clear

Clear the detection status automatically.

Select the checkbox to set the time to be cleared

automatically. When the checkbox is not selected, the

detection status will not be cleared unless the Clear

button is pressed.

Auto clear time

Set the time from when the camera tampering detection

is detected until the detection status is cleared

automatically.

OK/Cancel

See “Buttons common to every menu” on page 21.

Motion detection Tab — Set the

motion/VMF detection

Motion detection responds to moving objects in the

camera image and triggers an alarm.

In VMF, an alarm sounds when motion is detected under

the motion detection setting, entering or passing through

a specified area or inspection line. An alarm also sounds

when an object has been left or removed from a specified

area or inspection line.

The detected object will be displayed on the monitor in

the green frame. The removed object and left object will

be displayed in the magenta frame.

Note

Perform the following before setting the motion

detection.

• Deselect the checkbox of Stabilizer in the Installation

tab of the System menu.

What is VMF

VMF is a function for detecting an object entering or

passing through a specified area or inspection line, or

when an object has been left or removed from a specified

area or inspection line. Video/audio recording and/or

audio file playback can be synchronized with this alarm.

You can set the inspection methods to execute

independently. Intrusion and Passing can also be set to

execute in combination.

For example:

• An alarm sounds when an object enters areas A, B and

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Sony SNC-WR602 Seite 52

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Sony SNC-WR602

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info