699858
50
Zoom out
Zoom in
Vorherige Seite
1/73
Nächste Seite
Administrating the Camera
Setting the PTZF control — PTZF control Menu
50
Preset tour Tab — Setting a preset
tour
Up to 16 positions can be programmed, and the camera
moves to the programmed positions sequentially (Tour).
Up to five programs can be set as Tours A to E.
Preview screen
This screen is for monitoring images and configuring
preset tour settings.
Tour
Check to enable the tour function.
Resume time on inactivity
This item becomes active when Tour is set to On.
With this item, you can select whether you restart or stop
the tour after it has stopped by manual pan, tilt or zoom
operation or by camera movement to the preset position
triggered by an alarm.
Select the checkbox to set the resume time on inactivity.
Specify the wait time before the tour restarts, between 5
and 3600 seconds. The tour restarts automatically after
the specified time has elapsed.
Tour A to Tour E
Configure Tour A to Tour E respectively. Select the
checkbox to operate the tour.
Sequence
Set the sequence of the tour.
The preset positions saved using the Preset position tab
are displayed in the drop-down list at the bottom.
Select the preset position, then click Add. The selected
preset position is added in the Sequence list. Repeat this
procedure to specify the preset positions in sequence.
You can check the preset position by clicking Call.
To delete the preset position, click to select it in the list
and then click Delete.
To change the order in the list, select the preset position
and then click Move up or Move down.
To delete all preset position, click Delete All.
Speed
Select the speed of camera movement between 1 and 23,
or Fastest from the drop-down list. The camera moves
faster with a higher number setting. The fastest speed is
obtained with Fastest.
Stay time
Type a period of time during which the camera is to stay
at each preset position, between 1 and 3600 seconds.
Preview
Previews the order of movements of the selected tour.
The operation speed and stop time do not influence the
preview operation.
Stop
Stops the preview in action.
OK/Cancel
See “Buttons common to every menu” on page 21.
Serial Tab
Perform settings to control the camera according to data
which is input by peripheral devices via an external
serial interface. This unit complies with the Pelco-D
protocol. Make the settings according to the peripheral
devices connected to the network.
Standard
Select RS422, RS485 (half-duplex) or RS485 (full-
duplex).
Termination
Select the checkbox if you want to terminate it.
Camera ID
Specify the Camera ID of this unit.
OK/Cancel
See “Buttons common to every menu” on page 21.
50

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Sony SNC-WR632C wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Andere Handbücher von Sony SNC-WR632C

Sony SNC-WR632C Bedienungsanleitung - Deutsch - 82 seiten


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info