Bedienungsanleitung Sony SNC-XM637 (Seite 56 von 80) (Englisch)

699452

Zoom out

Zoom in

Vorherige Seite

1/80

Nächste Seite

Administrating the Camera

Setting the Sensor input/Camera tampering detection/Motion detection — Action input Menu

Event condition Tab

Create event execute conditions for each action.

Event condition 1, 2, 3, 4, 5

Select the event condition.

You can combine the alarm using the following event

execute conditions.

and: detect when both conditions happen within a

specified interval regardless of the sequence.

or: detect when either condition happens.

then: detect when each of the conditions happen within

a specified interval in sequence.

If you set the event condition to None, the following

alarm 1, 2, 3 menus appear.

1, 2, 3

Select the alarm.

Selectable alarms are as follows.

Displayed items vary depending on the function.

Sensor input 1: The external sensor that is connected to

sensor input 1 of the camera I/O port.

Sensor input 2: The external sensor that is connected to

sensor input 2 of the camera I/O port.

Presence sensor: The alarm is triggered by the presence

sensor function.

Camera tampering detection: The alarm is triggered if

the camera detects tampering, such as direction

shifting or spray.

Motion detection: The alarm is triggered by the motion

detection function.

VMF: The alarm is triggered by the VMF function.

Face detection: The alarm is triggered by the face

detection function.

Network disconnection: The alarm is triggered by

disconnection to a specific IP address.

Note

You cannot set more than two functions for Presence

sensor, Camera tampering detection or Network

disconnection in the same event condition.

Interval

Specify the interval time used when condition is set to

and, then.

In the case the condition is set as 1 and 2, the system

sounds an alarm when either 1 or 2 happens, and the

other happens within the specified interval.

In the case the condition is set as 1 then 2, the system

sounds an alarm when 1 happens, and then 2 happens

within the specified interval.

If you select “or” condition, this setting will be ignored.

The maximum duration to be set is 7200 seconds.

Sensor input Tab — Set the sensor

input 1/2

Sensor input mode

Set the direction of the detected input signal to the

sensor input terminal of the camera.

Normally open: Triggers an alarm when the sensor

input is short-circuited.

Normally closed: Triggers an alarm when the sensor

input is open-circuited.

Notes

• Allow at least two seconds for the input signal to be

detected; otherwise, some events may not be detected.

• When you use video streaming by SSL connection, set

as follows. Some events may not be detected if the

camera is not in the following conditions.

– Set the Bit rate below 1 Mbps.

– Set the Frame rate below 30 fps.

– Use the video streaming below two transmissions at

the same time.

OK/Cancel

See “Buttons common to every menu” on page 23.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Sony SNC-XM637 Seite 56

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Sony SNC-XM637

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info