Bedienungsanleitung Sony SNT-EP154 (Seite 18 von 97) (Englisch)

699866

Zoom out

Zoom in

Vorherige Seite

1/97

Nächste Seite

SNT EX101/SNT EX104/SNT EP104

Operating the unit

Switching Transmission Mode

Controlling alarm output

You can control Alarm output.

To use this function, you need to make Alarm output

active in the Trigger menu of the Administrator menu

(page 71).

Click Alarm output1 or Alarm output2 on the

Trigger panel.

The alarm output is switched by clicking.

The alarm output mode can be selected from

Toggle or Timer of Alarm output 1, 2 (page 71) in

the Trigger menu.

Tips

• For the connection of peripheral devices to the alarm

output of the I/O port, see the supplied Installation

Manual.

• The number of alarm outputs varies by model.

The number of selectable alarm output terminals is as

follows:

SNT-EX101/SNT-EX101E: 2

SNT-EX104/SNT-EX154: 4

SNT-EP104/SNT-EP154: None

Playing an audio file stored in the

system

You can play an audio file previously stored in the

system using the SNC audio upload tool.

To use this function, you need to make Voice alert1,

Voice alert2 and Voice alert3 active in the Trigger

menu of the Administrator menu (page 71).

Click Voice alert1, Voice alert2 or Voice alert3

on the Trigger panel.

Playback of the selected audio file starts and the

playback sound is output from the speaker

connected to the system.

Notes

• This operation is not available on the SNT-EP104 or

SNT-EP154.

• Voice alert configuration is only available for CH1 on

the SNT-EX154.

Switching Transmission

Mode

You can select the Transmission mode for video/audio

data.

This function can be used when Mode (video codec

mode) is set to MPEG4 or H.264 and the ActiveX

Viewer is used.

Note

The function may not operate correctly if you use

personal firewall software or antivirus software on your

computer. In that case, disable the software or select the

TCP mode.

Select TCP, Unicast or Multicast from the

Connection drop-down list in the Others panel.

TCP: This is normally selected.

When TCP is selected, HTTP communication is

adopted for video communications.

HTTP is the protocol used for reading the usual

Web page.

In an environment capable of reading Web pages,

you can watch video by selecting the TCP port.

Unicast: When Unicast is selected, RTP (Real-

time Transport Protocol) is adopted for video

communications. Since RTP is the protocol for

running video data, the video playback is smoother

than when TCP (HTTP) is selected. If a firewall is

installed between the camera and the computer, or

depending on the network environment, video may

not play back properly when Unicast is selected. In

this case, select TCP.

Multicast: This protocol is selectable when

Multicast streaming (page 32) is On. When

Multicast is selected, RTP (Real-time Transport

Protocol) and UDP multicast techniques are

adopted for video transmission. By selecting it, the

network transmission load of the camera can be

reduced. If a router that does not correspond to a

multicast or firewall is installed between the

camera and the computer, video may not play back

properly. In this case, select TCP or Unicast.

Note

When you are connected to a Proxy server, Unicast

or Multicast cannot be selected.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Sony SNT-EP154 Seite 18

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Sony SNT-EP154

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info