Bedienungsanleitung Sony STRDE945 (Seite 54 von 64) (Englisch)

36133

Zoom out

Zoom in

Vorherige Seite

1/64

Nächste Seite

Additional Information

No sound is heard from the center speaker.

, Make sure the sound field function is on (press

SOUND FIELD — MODE).

, Select a sound field containing the word “cinema”

or “virtual” (see page 33~35).

, Adjust the speaker volume (see page 22).

, Make sure the center speaker size parameter is set

to either SMALL or LARGE (see page 20).

No sound or only a very low-level sound is heard

from the rear speakers.

, Make sure the sound field function is on (press

SOUND FIELD – MODE).

, Select a sound field containing the word “cinema”

or “virtual” (see page 33~35).

, Adjust the speaker volume (see page 22).

, Make sure the rear speaker size parameter is set to

either SMALL or LARGE (see page 20).

The surround effect cannot be obtained.

, Make sure the sound field function is on (press

SOUND FIELD – MODE).

, Make sure that the SPEAKERS selector is set to A

or B (not A+B) if you connected two sets of front

speakers.

Recording cannot be done.

, Check that the components are connected correctly.

, Select the source component with a FUNCTION

button.

, When recording from a digital component, make

sure the input mode is set to ANALOG (see page

27) before recording with a component connected

to the analog MD/DAT or TAPE terminals

(STR-DE945) or the analog MD/TAPE terminals

(STR-DE845).

, When recording from a digital component, make

sure the input mode is set to DIGITAL (see page

27) before recording with the component

connected to the DIGITAL MD/DAT OUT

terminals (STR-DE945) or the DIGITAL MD/TAPE

OUT terminals (STR-DE845).

Radio stations cannot be tuned in.

, Check that the antennas are connected securely.

Adjust the antennas and connect an external

antenna if necessary.

, The signal strength of the stations is too weak

(when tuning in with automatic tuning). Use

direct tuning.

, Make sure you set the tuning interval correctly

(when tuning in AM stations with direct tuning)

(see pages 44 and 56).

, No stations have been preset or the preset stations

have been cleared (when tuning by scanning preset

stations). Preset the stations (see page 45).

, Press DISPLAY so that the frequency appears in

the display.

Nothing appears on the display

, When the display turns off immediately after the

receiver is turned on, press DIMMER to change the

display mode.

No picture or an unclear picture appears on the

TV screen or monitor.

, Select the appropriate function on the receiver.

, Set your TV to the appropriate input mode.

, Move your TV away from the audio components.

The remote does not function.

, Point the remote at the remote sensor

on the

receiver.

, Remove any obstacles in the path between the

remote and the receiver.

, Replace both batteries in the remote with new

ones, if they are weak.

, Make sure you select the correct function on the

remote.

, If the remote is set to operate the TV only, use the

remote to select a source or component other than

TV before operating the receiver or other

component.

Reference sections for clearing the

receiver’s memory

To clear See

All memorized settings page 18

Customized sound fields page 41

Troubleshooting

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Sony STRDE945 Seite 54

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info