Bedienungsanleitung Sony TA-FA1200 (Seite 20 von 91) (Englisch, Spanisch, Polnisch, Schwedisch)

51489

Zoom out

Zoom in

Vorherige Seite

1/91

Nächste Seite

Troubleshooting

If you experience any of the following

difficulties while using the amplifier, use this

troubleshooting guide to help you remedy the

problem. Should any problem persist, consult

your nearest Sony dealer.

Audio

There is no sound, no matter which

component is selected, or only a very

low-level sound is heard.

• Check that the speakers and components

are connected securely.

• Check that all speaker cords are connected

correctly.

• Check that both the amplifier and all

components are turned on.

• Check that VOLUME control is not set at

–∞ dB.

• Check that SPEAKERS (OFF/A/B/A+B)

is not set to “OFF” (page 11).

• Press MUTING to cancel the muting

function.

• Check that you have selected the correct

component with INPUT SELECTOR.

• Check that headphones are not connected.

• The protective device on the amplifier has

been activated. Turn off the amplifier,

eliminate the short-circuit problem, and

turn on the power again.

There is no sound from a specific

component.

• Check that the component is connected

correctly to the audio input jacks for that

component.

• Check that the cord(s) used for the

connection is (are) fully inserted into the

jacks on both the amplifier and the

component.

There is no sound from one of the

speakers.

• Connect a pair of headphones to the

PHONES jack to verify that sound is

output from the headphones. If only one

channel is output from the headphones, the

component may not be connected to the

amplifier correctly. Check that all the

cords are fully inserted into the jacks on

both the amplifier and the component. If

both channels are output from the

headphones, the speaker may not be

connected to the amplifier correctly.

Check the connection of the speaker which

is not outputting any sound.

• Make sure you have connected both the L

or R jack to an analog component and not

just to either the L or R jack. Use a

monaural-stereo cable (not supplied).

The left and right sounds are

unbalanced or reversed.

• Check that the speakers and components

are connected correctly and securely.

• Adjust the balance parameters by pressing

BALANCE on the remote.

There is severe hum or noise.

• Check that the speakers and components

are connected securely.

• Check that the connecting cords are away

from a transformer or motor, and at least 3

m away from a TV set or fluorescent light.

• Move your TV away from the audio

components.

• Make sure you have grounded the U

SIGNAL GND terminal (only when a

turntable is connected).

• The plugs and jacks are dirty. Wipe them

with a cloth slightly moistened with

alcohol.

Recording cannot be carried out.

• Check that the components are connected

correctly (page 7, 8).

• Select the source component using INPUT

SELECTOR (page 11, 12).

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Sony TA-FA1200 Seite 20

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Sony TA-FA1200

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info