214309
22
Zoom out
Zoom in
Vorherige Seite
1/54
Nächste Seite
© 2004 Sony Corporation
2-148-435-11 (1)
Data Projector
Operating Instructions
VPL-CS7
VPL-ES2
2
WARNING
To prevent fire or shock hazard, do
not expose the unit to rain or
moisture.
To avoid electrical shock, do not
open the cabinet. Refer servicing to
qualified personnel only.
For the customers in the USA
If you have any questions about this product,
you may call:
Sony Customer Information Service Center
1-800-222-7669 or http://www.sony.com/
The number below is for FCC related
matters only.
Declaration of Conformity
Trade Name: SONY
Model No.: VPL-CS7/VPL-ES2
Responsible Party: Sony Electronics Inc.
Address: 16450 W. Bernardo Dr, San Diego,
CA 92127 U.S.A.
Telephone Number: 858-942-2230
This device complies with Part 15 of the
FCC Rules. Operation is subject to the
following two conditions: (1) This device
may not cause harmful interference, and (2)
this device must accept any interference
received, including interference that may
cause undesired operation.
This equipment has been tested and found to
comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide
reasonable protection against harmful
interference in a residential installation.
This equipment generates, uses, and can
radiate radio frequency energy and, if not
installed and used in accordance with the
instructions, may cause harmful interference
to radio communications. However, there is
no guarantee that interference will not occur
in a particular installation. If this equipment
does cause harmful interference to radio or
television reception, which can be
determined by turning the equipment off and
on, the user is encouraged to try to correct
the interference by one or more of the
following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the
equipment and receiver.
- Connect the equipment into an outlet on a
circuit different from that to which the
receiver is connected.
- Consult the dealer or an experienced radio/
TV technician for help.
You are cautioned that any changes or
modifications not expressly approved in this
manual could void your authority to operate
this equipment.
This symbol is intended to
alert the user to the presence
of uninsulated “dangerous
voltage” within the
product’s enclosure that may
be of sufficient magnitude to
constitute a risk of electric
shock to persons.
This symbol is intended to
alert the user to the presence
of important operating and
maintenance (servicing)
instructions in the literature
accompanying the
appliance.
3
For the customers in Canada
This Class B digital apparatus complies with
Canadian ICES-003.
Voor de klanten in Nederland
Gooi de batterij niet weg
maar lever deze in als klein
chemisch afval (KCA).
The socket-outlet should be installed near
the equipment and be easily accessible.
CAUTION
RISK OF EXPLOSION IF BATTERY IS
REPLACED BY AN INCORRECT TYPE.
DISPOSE OF USED BATTERIES
ACCORDING TO THE
INSTRUCTIONS.
4
5
Table of Contents
Overview
Precautions .........................................6
Notes on Installation and Usage .........7
Features ..............................................9
Location and Function of Controls .11
Top/Front/Left Side ....................11
Rear/Right Side/Bottom .............11
Control Panel ..............................12
Connector Panel .........................13
Remote Commander ...................14
Projecting the Picture
Installing the Projector .....................16
Connecting the Projector ..................17
Connecting with a Computer ......17
Connecting with a VCR .............18
Connecting with a Monitor
Equipment (VPL-CS7
only) ................................19
Projecting .........................................19
Turning Off the Power .....................21
Convenient Function
Selecting the Menu Language ..........23
Security Lock ...................................24
Other Functions ................................25
Off & Go Function (VPL-CS7
only) ................................25
Effective Tools for Your
Presentation .....................26
Adjustments and Settings
Using the Menu
Using the MENU ............................. 27
The PICTURE SETTING Menu ..... 29
The INPUT SETTING Menu .......... 31
The SET SETTING Menu ............... 33
The MENU SETTING Menu .......... 35
The INSTALL SETTING Menu ..... 36
The INFORMATION Menu ............ 38
Maintenance
Replacing the Lamp ......................... 40
Cleaning the Air Filter ..................... 42
Others
Troubleshooting ............................... 43
Messages List ............................. 46
Specifications .................................. 48
Index ............................................... 52
6 Precautions
B Overview
Precautions
On safety
Check that the operating voltage of your
unit is identical with the voltage of your
local power supply.
Should any liquid or solid object fall into
the cabinet, unplug the unit and have it
checked by qualified personnel before
operating it further.
Unplug the unit from the wall outlet if it is
not to be used for several days.
To disconnect the cord, pull it out by the
plug. Never pull the cord itself.
The wall outlet should be near the unit and
easily accessible.
The unit is not disconnected to the AC
power source (mains) as long as it is
connected to the wall outlet, even if the
unit itself has been turned off.
Do not look into the lens while the lamp is
on.
Do not place your hand or objects near the
ventilation holes. The air coming out is
hot.
Be careful not to have your fingers caught
by the adjuster. The powered tilt adjuster
of this unit automatically extends when the
power is turned on, and is put away
automatically when the power is turned
off. Do not touch the unit while the
adjuster is in operation. Adjust the
powered tilt adjuster carefully after its
automatic operation is completed.
Do not spread a cloth or paper under the
unit.
On illumination
To obtain the best picture, the front of the
screen should not be exposed to direct
lighting or sunlight.
Ceiling-mounted spot lighting is
recommended. Use a cover over
fluorescent lamps to avoid lowering the
contrast ratio.
Cover any windows that face the screen
with opaque draperies.
It is desirable to install the projector in a
room where floor and walls are not of
light-reflecting material. If the floor and
walls are of reflecting material, it is
recommended that the carpet and wall
paper be changed to a dark color.
On preventing internal heat build-
up
After you turn off the power with the I / 1
key, do not disconnect the unit from the wall
outlet while the cooling fan is still running.
Caution
The projector is equipped with ventilation
holes (intake) and ventilation holes
(exhaust). Do not block or place anything
near these holes, or internal heat build-up
may occur, causing picture degradation or
damage to the projector.
On cleaning
To keep the cabinet looking new,
periodically clean it with a soft cloth.
Stubborn stains may be removed with a
cloth lightly dampened with a mild
detergent solution. Never use strong
solvents, such as thinner, benzene, or
abrasive cleansers, since these will
damage the cabinet.
Avoid touching the lens. To remove dust
on the lens, use a soft dry cloth. Do not use
a damp cloth, detergent solution, or
thinner.
Clean the filter at regular intervals.
On LCD data projector
The LCD data projector is manufactured
using high-precision technology. You
may, however, see tiny black points and/or
bright points (red, blue, or green) that
continuously appear on the LCD data
projector. This is a normal result of the
manufacturing process and does not
indicate a malfunction.
7Notes on Installation and Usage
Overview
Notes on Installation
and Usage
Do not install the projector in the following
situations. These installations may cause a
malfunction or damage to the projector.
Poorly ventilated
Allow adequate air circulation to prevent
internal heat build-up. Do not place the
unit on surfaces (rugs, blankets, etc.) or
near materials (curtains, draperies) that
may block the ventilation holes. When the
internal heat builds up due to the block-up,
the temperature sensor will function with
the message “High temp.! Lamp off in 1
min.” The power will be turned off
automatically after one minute.
Leave space of more than 30 cm (11
7
/8
inches) around the unit.
Be careful that the ventilation holes may
inhale tininess such as a piece of paper.
Highly heated and humid
Avoid installing the unit in a location
where the temperature or humidity is very
high, or temperature is very low.
To avoid moisture condensation, do not
install the unit in a location where the
temperature may rise rapidly.
Subject to direct cool or warm air
from an air-conditioner
Installing in such a location may cause
malfunction of the unit due to moisture
condensation or rise in temperature.
Near a heat or smoke sensor
Malfunction of the sensor may be caused.
Very dusty, extremely smoky
Avoid installing the unit in a very dusty or
extremely smoky environment. Otherwise,
the air filter will become obstructed, and this
may cause a malfunction of the unit or
damage it. Dust preventing the air passing
through the filter may cause a rise in the
internal temperature of the unit. Clean the
filter periodically.
Unsuitable Installation
8 Notes on Installation and Usage
Do not use the projector under the following
conditions.
Toppling the unit
Avoid using as the unit topples over on its
side. It may cause malfunction.
Tilting the unit out of the range of
the adjuster setting
Avoid using when the unit is tilted out of the
range of the adjuster setting. Such
installation may cause color shading or
shorten excessively the lamp life.
Tilting the unit to the right or left
Avoid tilting the unit to an angle of 15°, and
avoid installing the unit in any way other
than placing on the floor or suspending from
the ceiling. Such installation may cause
color shading or shorten the lamp life
excessively.
Blocking the ventilation holes
Avoid using something to cover over the
ventilation holes (exhaust/intake);
otherwise, the internal heat may build up.
For details on the ventilation holes (intake/
exhaust), see “Location and Function of
Controls” on page 11.
When using the projector at an altitude of
1,500 m or higher, turn on “High
Altitude Mode” in the INSTALL SETTING
menu. Failing to set this mode when using
the projector at high altitudes could have
adverse effects, such as reducing
the reliability of certain components.
Note on carrying the projector
The unit is manufactured using high-
precision technology. When transporting the
unit stored in the soft case, do not drop the
unit or subject it to shock, as this may cause
damage. When storing the unit in the soft
case, disconnect the AC power cord and all
other connecting cables, and store the
supplied accessories in a pocket of the soft
case.
Note on the screen
When using a screen with an uneven surface,
stripes pattern may rarely appear on the
screen depending on the distance between
the screen and the projector or the zooming
magnifications. This is not a malfunction of
the projector.
Unsuitable Conditions
Usage in High Altitude
9Features
Overview
Features
High brightness, high picture
quality
High brightness
This projector is equipped with a high-
efficiency optical system made possible
by adopting Sony’s proprietary optical
system that is equipped with a newly
developed LCD panel.
Because the VPL-CS7 utilizes a 185 W
UHP lamp, it can reproduce bright images
at 1800 ANSI lumen, while the VPL-ES2
utilizes a 157 W UHP lamp, that can
reproduce bright images at 1500 ANSI
lumen.
•High resolution
Three superhigh-aperture 0.62-inch
SVGA panels with approximately 480,000
pixels provide a resolution of 800 × 600
dots (horizontal/vertical) for RGB input,
and 600 horizontal TV lines for video
input.
High operability
Intelligent Auto-setup function
Simply press the power key, and the
projector automatically performs the
setups required before use. The projector
opens the lens protector, corrects the V
Keystone, and sets optimum conditions for
projection. This function is called
Intelligent Auto-setup.
For easier operations, the keys that will be
used frequently are allocated on the top of
the projector.
Short focus lens equipped
This projector is equipped with a short focus
lens that allows outputting to a larger screen
even in a limited space.
Various picture modes (VPL-ES2
only)
The best image can be projected by choosing
the mode suitable for the type of program or
room environment from among six picture
modes.
Accepts various input signals
Scan converter loaded
This projector has a build-in scan
converter that converts the input signal
within 800 × 600 dots.
Compatible input signals
This projector accepts video signals of
composite, S video, component and DTV
as well as VGA, SVGA and XGA signals,
which all can be displayed.
Compatible with six color systems
NTSC, PAL, SECAM, NTSC
4.43
*
, PAL-
M, or PAL-N color system can be selected
automatically.
Easy presentation
Simple setup with external equipment
This projector is preset for 32 kinds
of
input signals. You can project images from
an external signal source just by
connecting the equipment with the
supplied cable.
..............................................................................................................................................................
*NTSC4.43 is the color system used when playing back a video recorded on NTSC on a NTSC4.43
system VCR.
Windows is a registered trademark of Microsoft Corporation in the United States and/or other
countries.
VGA, SVGA and XGA are registered trademarks of the International Business Machines
Corporation, U.S.A.
Kensington is a registered trademark of Kensington Technology Group.
Macintosh is a registered trademark of Apple Computer, Inc.
VESA is a registered trademark of Video Electronics Standard Association.
Display Data Channel is a trademark of Video Electronics Standard Association.
10 Features
Easy-to-use Remote Commander
The Remote Commander is equipped with
various convenient keys, including the D
ZOOM key for zooming in on the image and
the FREEZE key for keeping the image
projected even if the equipment is
disconnected.
High portability
Light weight/small size/simple design
This projector has been miniaturized to
approx. 2.8 kg (6 lb 3 oz) (VPL-ES2)/
approx. 2.9 kg (6 lb 6 oz) (VPL-CS7) in
weight and B5-file size.
Its simple yet sophisticated design fits
comfortably in your office.
Off & Go function (VPL-CS7 only)
The cooling fan built in the projector will
work even after turning the power off and
the power cord is disconnected. This enables
you to move the projector to another location
immediately after turning it off.
Security functions
Security lock
This function makes it possible to project no
picture on the screen unless the required
password is entered when the projector is
turned on.
Panel key lock
This function locks all the operation keys on
the control panel of the projector, allowing
use of the keys on the Remote Commander.
This prevents the projector from operating
incorrectly.
11Location and Function of Controls
Overview
Location and
Function of Controls
1 Control panel
For details, see “Control Panel” on
page 12.
2 Lens protector (lens cover)
The lens protector automatically opens
when the power is turned on.
3 Ventilation holes (exhaust)
4 Remote control detector
5 Adjuster (hind pad)
Turn the adjuster to the right or left for
minor tilt adjustment of the projected
picture.
6 Ventilation holes (intake)/Lamp
cover
7 Ventilation holes (intake)/air
filter cover
Do not place anything near the
ventilation holes as it may cause
internal heat build-up.
Do not place your hand or objects
near the ventilation holes as it may
cause the air coming out heat build-
up.
To maintain optimal performance, clean
the air filter every 500 hours.
For details, see “Cleaning the Air
Filter” on page 42.
8 Ventilation holes (intake)
9 Powered tilt adjuster
0 Indicators
POWER SAVING
Lights up when the projector is in power
saving mode.
TEMP (Temperature)/FAN
Lights up or flashes under the following
conditions:
Lights up when temperature inside the
projector becomes unusually high.
Fashes when the fan is broken.
LAMP/COVER
Lights up or flashes under the following
conditions:
Lights up when the lamp has reached
the end of its life or becomes a high
temperature.
Flashes when the lamp cover is not
secured firmly.
For details, see pages 34, 45.
qa Focus ring
Adjusts the picture focus.
qs Zoom ring
Adjusts the picture size.
Top/Front/Left Side
Rear/Right Side/Bottom
5
4
6
7
8
9
qa
0
qs
qd
qf
qg
Notes
12 Location and Function of Controls
qd Connector panel
For details, see “Connector Panel” on
page 13.
qf Speaker
qg Security lock
Connects to an optional security cable
(Kensington’s).
Web page address:
http://www.kensington.com/
1 I / 1 (on/standby) key
Turns on the projector when the
projector is in standby mode. The ON/
STANDBY indicator around the I / 1
key lights in green when the power is
turned on.
2 ON/STANDBY indicator (located
around the
I / 1 key)
Lights up or flashes under the following
conditions:
Lights in red when a AC power cord is
plugged into a wall outlet. Once in
standby mode, you can turn on the
projector with the I / 1 key.
Lights in green when the power is
turned on.
Flashes in green while the cooling fan
runs for about 90 seconds (VPL-ES2)/
for about 70 seconds (VPL-CS7) after
the power is turned off with the I / 1
key.
For details, see page 21.
3 INPUT key
4 TILT adjustment key
For details, see“Projecting” on
page 19.
5 MENU key
Displays the on-screen menu. Press
again to clear the menu.
6 ENTER key
Enters the settings of items in the menu
system.
7 Arrow keys (f/F/g/G)
Select the menu or to make various
adjustments.
Control Panel
INPUT MENU
PUSH
ENTER
TILT
132456
7
13Location and Function of Controls
Overview
VPL-CS7
VPL-ES2
1 INPUT A connector (HD D-sub
15-pin, female)
Connect to external equipment such as a
computer.
Connects to the monitor output on a
computer using the supplied cable.
When inputting a component or 15k
RGB signal, use an optional cable.
For details, see “To connect to a video
GBR/component output connector” on
page 18.
2 Video input connector
Connect to external video equipment
such as a VCR.
VIDEO (phono type): Connects to
the composite video output of video
equipment.
S VIDEO (mini DIN 4-pin):
Connects to the S video output (Y/C
video output) of video equipment.
3 AUDIO (stereo minijack)
connector
When listening to sound output from the
computer, connect to the audio output of
the computer.
When listening to sound output from the
VCR, connect to the audio output of the
VCR.
4 Monitor output connector (VPL-
CS7 only)
Connects to the monitor input on a
monitor. Outputs the signal from a
computer connected to INPUT A.
5 AC IN socket
Connects the supplied AC power cord.
6 Component input connector (for
VPL-ES2 only)
According to the connected equipment,
component (Y/C
B/CR), HDTV or DTV
(Y/PB/PR) signal is selected.
Connector Panel
INPUT A
S VIDEO
VIDEOAUDIO
MONITOR OUT
1
2
3
4
5
INPUT A
S VIDEO
VIDEOAUDIO
YP
B
/C
B
P
R
/C
R
1
2
3
5
6
14 Location and Function of Controls
1 I / 1 (on/standby) key
2 ENTER/arrow key (
v/V/b/B)
Press the center of the key to use
ENTER.
3 MENU key
4 D ZOOM +/
key
Enlarges the image at a desired location
on the screen.
5 Infrared transmitter
6 FREEZE key
Used to freeze the picture projected. To
cancel the freeze function, press the key
again.
7 INPUT key
8 APA (Auto Pixel Alignment) key
Adjusts a picture clearest automatically
while a signal is input from a computer.
For details, see “Smart APA” in the SET
SETTING menu on page 33.
9 D KEYSTONE key
Used to adjust the tilt of the projector, or
the trapezoidal distortion of the image
manually. Each time you press this key,
the Tilt menu and the V Keystone menu
is displayed alternately. Use the arrow
key (v
/V/b/B) for the adjustment.
q; RESET key
Resets the value of an item back to its
factory preset value or returns the
enlarged image back to its original size.
This key functions when the menu or a
setting item is displayed on the screen.
Before using the Remote
Commander
Pull out the clear film from the lithium
battery holder.
To replace battery
1 Release the lock of the lithium battery
holder by picking it, and pull out the
holder from the Remote Commander.
2 Install the lithium battery.
3 Put the lithium battery holder back
into the Remote Commander.
Notes on the lithium battery
Keep the lithium battery out of the reach of
children.
Should the battery be swallowed,
immediately consult a doctor.
Remote Commander
+ side facing
upward
15Location and Function of Controls
Overview
Notes on Remote Commander
operation
Make sure that nothing obstructs the
infrared beam between the Remote
Commander and the remote control
detector on the projector. Direct the
Remote Commander toward the remote
control detector.
The operation range is limited. The shorter
the distance between the Remote
Commander and the remote control
detector is, the wider the angle within
which the commander can control the
projector becomes.
16 Installing the Projector
B Projecting the Picture
Installing the Projector
This section describes how to install the projector.
The distance between the lens and the screen varies depending on the size of
the screen. Use the following table as a guide.
There may be a slight difference between the actual value and the design value shown
in the table above.
Unit: m (feet)
Screen size
(inches)
40 60 80 100 120 150 200 300
Minimum
Distance
1.1
(3.6)
1.7
(5.6)
2.3
(7.5)
2.9
(9.5)
3.5
(11.5)
4.4
(14.4)
5.9
(19.4)
8.8
(28.9)
Maximum
Distance
1.4
(4.6)
2.1
(6.9)
2.8
(9.2)
3.5
(11.5)
4.2
(13.8)
5.3
(17.4)
7.0
(23)
10.6
(34.8)
Distance between the screen and
the center of the lens
17Connecting the Projector
Projecting the Picture
Connecting the
Projector
When you connect the projector,
make sure to:
Turn off all equipment before making any
connections.
Use the proper cables for each connection.
Insert the cable plugs firmly; loose
connections may increase noise and
reduce performance of picture signals.
When pulling out a cable, be sure to pull it
out from the plug, not the cable itself
This section describes how to connect the
projector to a computer.
For more information, refer to the
computer’s instruction manual.
To connect a computer
Ex. VPL-CS7
1HD D-sub 15-pin cable (supplied)
2Stereo audio connecting cable (not supplied)
(Use a no-resistance cable)
The projector accepts VGA, SVGA, XGA
signals. However, we recommend that you
set the output mode of your computer to
SVGA mode for the external monitor.
If you set your computer, such as a notebook
type, to output the signal to both your
computer’s display and the external monitor,
the picture of the external monitor may not
appear properly. Set your computer to output
the signal to only the external monitor.
For details, refer to the computer’s
operating instructions supplied with your
computer.
Connecting with a Computer
Notes
INPUT A
S VIDEO
VIDEO
AUDIO
MONITOR OUT
to audio
output
Left side
2
to monitor
output
Computer
1
18 Connecting the Projector
To connect a Macintosh computer equipped
with video output connector of a type having
two rows of pins, use a commercially available
plug adaptor.
This section describes how to connect the
projector to a VCR.
For more information, refer to the
instruction manuals of the equipment you
are connecting.
To connect to a video or S video
output connector
Ex. VPL-CS7
1Stereo audio connecting cable (not supplied)
(Use a no-resistance cable)
2Video cable (not supplied) or
3S-Video cable (not supplied)
To connect to a video GBR/
component output connector
Ex. VPL-ES2
1SMF-402 Signal Cable (not supplied)
HD D-sub 15-pin (male) y 3 × phono plug
or
2Component video (3 × phono plug
y 3 ×
phono plug (not supplied) (Use a 75
coaxial cable) (VPL-ES2 only))
3Stereo audio connecting cable (not supplied)
(Use a no-resistance cable)
Set the aspect ratio using “Wide Mode” in
the INPUT SETTING menu according to the
input signal.
When you connect the INPUT A connector
on the unit to a video GBR output connector,
select “Video GBR,” or when you connect it
to a component output connector, select
“component” with the “Input-A Signal Sel.”
setting in the SET SETTING menu. The
input selection must be performed before
inputting the signal.
Use the composite sync signal when you
input the external sync signal from video
GBR/component equipment.
Note
Connecting with a VCR
AUDIO
AUDIO
INPUT A
S VIDEO
VIDEO
MONITOR OUT
VCR
to S video
output
Left side
to audio
output
to video
output
2
1
3
Notes
AUDIO
YPB/CBPR/CR
AUDIO
INPUT A
S VIDEO
VIDEO
Left side
to
audio
output
15k RGB/Component equipment
to RGB/
component
output
2
3
1
19Projecting
Projecting the Picture
This section describes how to connect the
projector to a monitor equipment.
For more information, refer to the
instruction manuals of the equipment you
are connecting.
* This projector is not guaranteed for
connecting more than 2 monitors in loop-
through connection.
Projecting
1 Plug the AC power cord into a wall
outlet, then connect all equipment.
The ON/STANDBY indicator lights in
red and the projector goes into standby
mode.
2 Press the I / 1 key.
The ON/STANDBY indicator lights in
green and the Intelligent Auto-setup
starts. The lens protector opens, and the
powered tilt adjuster rises and stops at
the previously adjusted position.
3 Turn on the equipment connected to
the projector.
Connecting with a Monitor
Equipment (VPL-CS7 only)
MONITOR OUT
AUDIO
INPUT A
S VIDEO
VIDEO
Left side
Monitor cable (not
supplied)
HD D-sub 15-pin (male)
HD D-sub 15-pin
(male)
to monitor
input
Monitor equipment
INPUT MENU
PUSH
ENTER
TILT
8
ON/STANDBY indicators
Remote control
detector
20 Projecting
4 Press the INPUT key to select the
input source.
Each time you press the key, the input
signal switches as follows:
Smart APA (Auto Pixel Alignment)
adjusts the picture of the connected
equipment so that it is projected clearly.
5 Switch the equipment to be connected
to output to the projector.
Depending on the type of your
computer, for example a notebook, or an
all-in-one LCD type, you may have to
switch the computer to output to the
projector by pressing certain keys
(e.g., , etc.), or by
changing your computer’s settings.
•If “Auto Input Search” is set to “On,” the
projector searches for the signals from
the connected equipment and displays
the input channel where the input signals
are found.
For details, see “Auto Input Search”
in the SET SETTING menu on page 33.
•The Smart APA is effective for the input
signal from a computer only.
6 Adjust the position of the picture.
To adjust using the Remote
Commander
To adjust the position of the picture,
using the Remote Commander, press the
D KEYSTONE key on the Remote
Commander to display the Tilt menu and
adjust the tilt using the v/V/b/B keys.
To adjust using the Control Panel
Press f on F of the TILT key to adjust
the tilt of the projector.
When you adjust the powered tilt
adjuster with the TILT key, the V
keystone adjustment is performed at the
same time. If you do not want to perform
the automatic keystone adjustment, set
the V Keystone menu to “Manual.” (See
page 36.)
If you set the “V Keystone” adjustment
to “Auto,” the “V Keystone” correction
is automatically adjusted. However, it
may not be perfectly adjusted depending
To input from Press INPUT
to display
Computer connected to the
INPUT A connector
INPUT A
Equipment connected to the
component connector
Component
(VPL-ES2
only)
Video equipment connected to
the VIDEO input connector
VIDEO
Video equipment connected to
the S VIDEO input connector
S VIDEO
INPUT A
t
Component
t
VIDEO
t
S VIDEO
t
(VPL-ES2 only)
VGA
LCD
//
,
F7
Fx
Fn
or
Fx:“x” indicate an optional numerical
value. The Fx key varies depending
on a computer’s makers.
and
Notes
Notes
TILT
to lower the
projector
to raise the
projector
TILT adjustment key
Powered tilt adjuster
21Turning Off the Power
Projecting the Picture
on the room temperature or the screen
angle. In this case, adjust it manually.
Press the D KEYSTONE key on the
Remote Commander until “V Keystone”
appears on the screen, and adjust the
value with the
v/V/v/B key. The
corrected value is effective until the
power turn off.
Be careful not to let the projector down
on your fingers.
Do not push hard on the top of the
projector with the powered tilt adjuster
out. It may be occurred malfunction.
7 Turn the zoom ring to adjust the size
of the picture.
8 Turn the focus ring to adjust the focus.
Looking into the lens when projecting may
cause injury to your eyes.
Turning Off the
Power
1 Press the I / 1 key.
“POWER OFF? Please press I / 1 key
again.” appears to confirm that you want
to turn off the power.
A message disappears if you press any key
except the I / 1 key, or if you do not press
any key for five seconds.
2 Press the I / 1 key again.
The powered tilt adjuster is put away in
the projector and the lens protector
closes. The ON/STANDBY indicator
flashes in green and the fan continues to
run for about 70 seconds (VPL-CS7)/for
about 90 seconds (VPL-ES2) to reduce
the internal heat. Also, the ON/
STANDBY indicator flashes quickly for
the first 60 seconds. During this time,
you will not be able to light up again the
ON/STANDBY indicator with the I / 1
key.
3 Unplug the AC power cord from the
wall outlet after the fan has stopped
running and the ON/STANDBY
indicator has light in red.
When you cannot confirm the on-
screen message
When you cannot confirm the on-screen
message in a certain condition, you can turn
off the power by holding the I / 1 key for
about two seconds.
Attention
Note
22 Turning Off the Power
Do not unplug the AC power cord while
the fan is still running; otherwise, the fan
will stop even though the internal heat is still
high, which could result in a breakdown of
the projector. (VPL-ES2 only)
The internal circuitry of the Off & Go
function may cause the fan to continue to
operate for a short time even after the I /
1
key is pressed to turn off the power and the
ON/STANDBY indicator changes to red.
(VPL-CS7 only)
For details, see “Off & Go Function
(VPL-CS7 only)” on page 25.
Notes
22

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Sony vpl cs7 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info