Bedienungsanleitung Sony VPL-CW275 (Seite 21 von 54) (Englisch)

645222

Zoom out

Zoom in

Vorherige Seite

1/54

Nächste Seite

The INPUT SETTING Menu

Adjustments and Settings Using a Menu

The INPUT SETTING Menu

For adjusting the size, position, and aspect ratio of the projected image for each input signal.

*1: Available when a computer signal is input from the RGB input connector (INPUT A/INPUT B).

*2: Available when a computer signal is input from the RGB input connector (INPUT A/INPUT B)

or a video signal is input from the YP

BPR input connector (INPUT A).

*3: • Note that if the projector is used for profit or for public viewing, modifying the original picture

by switching to the aspect mode may constitute an infringement of the rights of authors or

producers, which are legally protected.

• Depending on the input signal, setting items for aspect ratio or some other setting items cannot

be set in some cases, or changing the aspect ratio setting may have no effect.

• A part of the image may be displayed in black, depending on the setting item.

*4: Available when a video signal is input from the YP

BPR input connector (INPUT A) or the HDMI

input connector (INPUT C).

*5: VPL-CW275 only.

Items Item descriptions

Adjust Signal Adjusts the image of computer signal. Use this item if the edge of the image

is cut and reception is bad.

Dot Phase

Adjusts the dot phase of the display pixel and the input signal. Set to the

value where looks clearest.

H Size

The higher the setting, the wider the horizontal image elements (pitch). The

lower the setting, the narrower the horizontal image elements (pitch).

Shift

H: The higher the setting, the farther right the image is projected on the

screen. The lower the setting, the image farther left.

V: The higher the setting, the farther up the image is projected on the screen.

The lower the setting, the image farther down.

Aspect

Changes the aspect ratio of the projected image (page 22).

When the

computer

signal is

input

Normal: Displays the image on the center point of the projected image

without changing the resolution of the input signal or enlarging the image.

Full1: Displays the image to fit the maximum projected image size without

changing the aspect ratio of the input signal.

Full2: Displays the image to fit the maximum projected image size.

Full3

: Displays a 1280 × 720 dot picture on the screen without changing

the aspect ratio of the original image.

When the

video signal

is input

(VPL-

CX275)

4:3: Displays the image to fit the maximum projected image size with an

aspect ratio fixed to 4:3.

16:9: Displays the image to fit the maximum projected image size with an

aspect ratio fixed to 16:9.

Zoom: Display the center point of the projected image to zoom.

When the

video signal

is input

(VPL-

CW275)

4:3: Displays the image with an aspect ratio fixed to 4:3.

16:9: Displays the image with an aspect ratio fixed to 16:9.

Zoom: Displays the image to enlarge without changing the aspect

ratio of the original image.

Wide Zoom: Displays the image to enlarge with minimum distortion.

Over Scan

On/Off: When set to “On”, the outer edges of the picture will be hidden.

Select this setting when noise appears along the edge of the picture.

Notes

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Sony VPL-CW275 Seite 21

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info