Bedienungsanleitung Sony VPLSX225 (Seite 27 von 78) (Englisch)

549899

Zoom out

Zoom in

Vorherige Seite

1/78

Nächste Seite

The Connection/Power Menu

Adjustments and Settings Using a Menu

*1: This may not be optimum depending on the input signal. In this case set manually according

to the connected equipment.

*2: When “Standby Mode” is set to “Low,” the network and network control function cannot be

operated while the projector is in standby mode.

*3: This varies depending on the “Lamp Mode” setting.

*4: As the lamp is dimmed gradually, you may not notice any change in brightness. You might only

notice that the lamp has dimmed when its brightness is restored after there is a change in input

signal.

*5: This mode does not work for about three minutes after the lamp lights. A change in signal may

not be detected depending on the input image. The lamp may become brighter at intervals

during lamp dimming. However, this is not a malfunction. If With No Input is set, it takes

priority.

*6: Select “Off” to avoid entering standby mode when there is no input signal.

*7: Does not function when “Type A USB”, “Type B USB” or “Network” is selected as the input.

In this case, it becomes equivalent to “Standard.”

*8: Reflecting changes in WLAN settings may take a few moments.

*9: To set the IP address manually, select “Manual”, press “Apply”, then enter the IP address.

*10: When you send images or files from a tablet PC/smartphone and display them (page 41), set

“WLAN Network” to “Access Pt. (Auto)” or “Access Pt. (Manual),” to use USB wireless LAN

module IFU-WLM3 (not supplied) as a wireless access point.

*11: The factory default settings for “Access Pt. (Manual)” are as follows.

SSID: VPL + MAC address for LAN

Security Method: WEP(64bit)

Password: sony1

To change the settings for “Access Pt. (Manual)”, use a Web browser.

For details, see “Setting the WLAN Network of the projector” (page 33).

If “Access Pt. (Manual)” is set, when you use Presentation Function via Network (page 39),

select “Manual Connect” to connect to the network.

*12: For changing the settings for “Client,” use the Web browser for change. For details, see

“Setting the WLAN Network of the projector” (page 33).

*13: Constant Brightness mode will be enabled for about 2,000 hours after it is activated at early

usage. After this period, it will be disabled automatically. Activated time and brightness may

vary depending on the usage conditions.

*14: If the projector cannot connect wirelessly, click [Apply] once again to make sure the

connection is established. For details, see “Setting the WLAN Network of the projector”

(page 33).

Direct Power On On/Off: When set to “On,” you can turn the power on without going to

Standby mode when the AC power cord is connected to a wall outlet.

With the projector turned off, you can also unplug the AC power cord

without going to Standby mode, regardless of the Direct Power On

setting.

Notes

Items Item descriptions

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Sony VPLSX225 Seite 27

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info