Bedienungsanleitung Sony XM-1ES (Seite 11 von 100) (Deutsch, Englisch, Holländisch, Französisch, Spanisch, Schwedisch)

796236

Zoom out

Zoom in

Vorherige Seite

1/100

Nächste Seite

11GB

*1 If you have the factory original or some other car audio

unit without a remote output for the amplifier, connect

the remote input (REMOTE) terminal to the ACC power

supply. In high level input connection, the amplifier can

also be activated without a need for REMOTE connection.

However, this function is not guaranteed for all car audio

units.

*2 Ground (earth) to the car chassis.

+12 V terminal

•Connect the +12 V power supply lead to the +12 V

terminal only after all the other connections have

been completed.

•Use a +12 V power supply lead with a 100 A fuse

attached.

•During full-power operation, a current of more

than 100 A will run through the system. Therefore,

make sure the leads to be connected to the +12 V

terminal are at least 2-Gauge (AWG-2) or have a

sectional area of more than 34 mm² (1 7/16 in²).

• All power leads connected to the positive battery

post should be fused within 450 mm (17 3/4 in) of

the battery post before they pass through any

metal.

•Make sure the leads connecting from the car

battery to the metal point on the car chassis are at

least of a lead gauge equal to that of the +12 V

power supply lead connected from the battery to

the amplifier.

•Make sure the leads connecting from the car

battery to the metal point on the car chassis are

not more than 0-Gauge (AWG-1/0) or have a

sectional area of 55 mm² (2 5/16 in²), and at least

of a lead gauge equal to that of the +12 V power

supply lead connected from the battery to the

amplifier.

GROUND terminal

• Be sure to connect the ground (earth) lead

securely to a metal point on the car chassis. A

loose connection may cause the amplifier to

malfunction.

• During full-power operation, a current of more

than 100 A will run through the system. Therefore,

make sure the leads to be connected to the

GROUND terminal are at least 2-Gauge (AWG-2) or

have a sectional area of more than 34 mm²

(1 7/16 in²).

REMOTE terminal

• To turn on the amplifier using a dedicated remote

turn-on lead, set the TURN-ON switch to

“REMOTE”, then connect the remote output

(REMOTE OUT) of your car audio unit to the

REMOTE terminal.

• When using a car audio unit without a remote

output (REMOTE OUT) for the amplifier, connect

the REMOTE terminal to the ACC power supply of

your car or use the signal sensing turn-on setting

instead.

• Use a remote turn-on lead with a thickness from

AWG-8 to AWG-18 or a sectional area from

8.4 mm² (11/32 in²) to 0.82 mm² (1/16 in²).

Notes on using high-level sensing turn-on

settings

• In high level input connection, the amplifier can

also be activated without the need for a REMOTE

connection. However, this function is not

guaranteed for all car audio units.

• By setting the TURN-ON switch to “SIGNAL”, the

amplifier operates automatically when a turn-on

signal is received from the INPUT connector.

Power Connections

+12 V REMOTE

REMOTE

OUT*1

GROUND

Fuse (100 A)

to a metal point

on the car chassis

less than 450 mm (17 3/4 in)

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Sony XM-1ES Seite 11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info