Bedienungsanleitung Sony XM-4ES (Seite 8 von 100) (Deutsch, Englisch, Holländisch, Französisch, Spanisch, Schwedisch)

796237

Zoom out

Zoom in

Vorherige Seite

1/100

Nächste Seite

8GB

Connection

•Before making any connections, disconnect the

ground (earth) terminal of the car battery to avoid

short circuits. Connect this amplifier to the +12 V

power supply lead only after all other leads have

been connected.

•This amplifier is designed for negative ground

(earth) 12 V DC operation only.

•Do not operate the amplifier on a weak battery as

the amplifier requires a good power supply for

optimum performance.

•If your car is equipped with a computer system for

purposes such as navigation, disconnecting the

ground (earth) terminal of the car battery may

damage the computer memory. Leave the ground

(earth) lead connected and connect this amplifier

to the +12 V power supply lead only after all other

leads have been connected to prevent short

circuits.

• When connecting and installing the input and

output cables, keep them away from the +12 V

power supply lead. Running them close together

may generate interference noise.

Notes on making connections

• To connect to the terminals on the connector

panel and to adjust various settings, remove the

top cover to access the control panel (top panel).

•When you tighten the screw, be careful not to

apply too much torque as doing so may damage

the terminals or cables.

*1 If you have the factory original or some other car audio

unit without a remote output for the amplifier, connect

the remote input (REMOTE) terminal to the ACC power

supply. In high level input connection, the amplifier can

also be activated without a need for REMOTE connection.

However, this function is not guaranteed for all car audio

units.

*2 Ground (earth) to the car chassis.

+12 V terminal

•Connect the +12 V power supply lead to the +12 V

terminal only after all the other connections have

been completed.

•Use a +12 V power supply lead with a 80 A fuse

attached.

•During full-power operation, a current of more

than 80 A will run through the system. Therefore,

make sure the leads to be connected to the +12 V

terminal are at least 4-Gauge (AWG-4) or have a

sectional area of more than 22.0 mm² (7/8 in²).

• All power leads connected to the positive battery

post should be fused within 450 mm (17 3/4 in) of

the battery post before they pass through any

metal.

•Make sure the leads connecting from the car

battery to the metal point on the car chassis are at

least of a lead gauge equal to that of the +12 V

power supply lead connected from the battery to

the amplifier.

•Make sure the leads connecting from the car

battery to the metal point on the car chassis are

not more than 0-Gauge (AWG-1/0) or have a

sectional area of 55 mm² (2 5/16 in²), and at least

of a lead gauge equal to that of the +12 V power

supply lead connected from the battery to the

amplifier.

REMOTE

12 V

GROUND

REMOTE

12 V

GROUND



Power Connections

REMOTE

OUT*

+12 V REMOTE

GROUND

Fuse (80 A)

to a metal point

on the car chassis

less than 450 mm (17 3/4 in)

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Sony XM-4ES Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info