Bedienungsanleitung Sony XM-GS4 (Seite 5 von 152) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Schwedisch)

796240

Zoom out

Zoom in

Vorherige Seite

1/152

Nächste Seite

5GB

Parts for Installation and

Connections

This parts list does not include all the package

contents.

Installation

Mount the unit either inside the trunk (boot) or

under a seat.

Choose the mounting location carefully so the

unit will not interfere with the normal movements

of the driver and it will not be exposed to direct

sunlight or hot air from the heater.

Do not install the unit under the floor carpet,

where the heat dissipation from the unit will be

considerably impaired.

Mounting the unit

First, place the unit where you plan to install it, and

mark the positions of the 4 screw holes on the

mounting board (not supplied). Then drill a 3 mm

(1/8 in) pilot hole at each mark and mount the unit

onto the board with the supplied mounting screws.

The mounting screws are all 14 mm (9/16 in) long, so

make sure that the mounting board is thicker than

14 mm (9/16 in).

Connections

Before making any connections, disconnect the

ground (earth) terminal of the car battery to avoid

short circuits.

Be sure to use speakers with an adequate power

rating. If you use small capacity speakers, they

may be damaged.

This is a Phase-Inverted Amplifier.

Do not connect the  terminal of the speaker

system to the car chassis, and do not connect the

 terminal of the right speaker with that of the

left speaker.

Install the input and output cords away from the

power supply wire. Running them close together

may generate interference noise.

This unit is a high powered amplifier. Therefore, it

may not perform to its full potential if used with

the speaker cords supplied with the car.

If your car is equipped with a computer system for

navigation or some other purpose, do not remove

the ground (earth) wire from the car battery. If you

disconnect the wire, the computer memory may

be erased. To avoid short circuits when making

connections, disconnect the +12 V power supply

wire until all the other wires have been

connected.

Making the terminal connections

Note

When you tighten the screw, be careful not to apply too

much torque as doing so may damage the screw (the

torque value should be less than 1 N•m).

Connect the +12 V power supply wire only after all

the other wires have been connected.

Be sure to connect the ground (earth) wire of the

unit securely to a metal point of the car. A loose

connection may cause a malfunction of the

amplifier.

Be sure to connect the remote control wire of the

car audio unit to the remote input (REM) terminal.

When using a car audio unit without a remote

output for the amplifier, connect the remote input

(REM) terminal to the accessory power supply.

Installation and Connections



ø4 × 14 mm

(3/16 × 9/16 in)

× 4



Power Connections

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Sony XM-GS4 Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info