Bedienungsanleitung Sorel MHCC (Seite 20 von 24) (Englisch)

812335

Zoom out

Zoom in

Vorherige Seite

1/24

Nächste Seite

Room Controller

This value is used to appoint the amount of influence the room temperature has on the reference flow temperature, as a per-

centage. For every degree of the room temperature deviates from the reference room temperature, the percentage of the cal-

culated reference flow temperature set here is added to or subtracted from the reference flow temperature, so long as it is within

the limits of the min. and max. flow temperatures that can be set in the protective functions.

Example: Reference room temp.: e.g. 25 °C; room temp.: e.g. 20 °C ±5 °C. Calculated reference temp.: e.g. 40 °C: room con-

troller: 10 %= 4 °C 5 X 4 °C= 20 °C. Accordingly, 20 °C are added to the reference flow temperature, giving 60 °C. If the value is

higher than the one set in max. flow temp, the resulting temperature is the one set in max. flow temp.

Room Reference (Day)

The desired room temperature for day mode. As long as this temperature is not reached, the reference flow temperature is raised

and/or lowered according to the percent setting in ‚room controller‘. If ‚room controller‘ is set to 0 %, this function is deactivated.

Room Reference (Night)

The desired room temperature for night mode. As long as this temperature is not reached, the reference flow temperature is

raised and/or lowered according to the percent setting in ‚room controller‘. If ‚room controller‘ is set to 0 %, this function is deac-

tivated.

In the modes ‚Set point‘ and ‚Set point program, the room controller has no influence.

Thermostat

The room controller is set here. If no RC21 is connected, a room controller from another heating controller over can be selected

over the CAN bus. The CAN bus ID of controller is shown in Menu 6, ‚Service Data‘ under ‚CAN Bus ID‘. Choose the RC21 with

the CAN Bus ID of the corresponding controller. The heat controller now obtains the switch position and rotary switch position

from the CAN bus.

Eco Display Mode

In Eco Display Mode the backlight of the display is switched off if no buttons are pushed for 2 minutes.

If a message exists, the backlight does not switch off until the message has been scanned by the user.

Network

If applicable, the network settings of the connected data logger have to be adjusted

Access Control

This menu lets you give up to 4 users access to the data logger. The users that are registered then have access to the controller

or respectively the data logger.

To add a user in the list, select <add user>. Leave the now visible menu open und connect to the address of the connector or

respectively the data logger. Your user name is going to appear in this menu and can be selected and confirmed with ‘OK’.

Note

You can find the address of the connector or respectively the data logger on the address sticker on the outside of the casing.

Pointers and help on how to establish a connection you can find in the enclosed SOREL connect instructions or the instructions

of the data logger.

Select a user with ‘OK’ to grant access.

To revoke access again, choose one of the users from your list and choose <remove user>.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Sorel MHCC Seite 20

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Sorel MHCC

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info