Bedienungsanleitung Sorel SBMC (Seite 16 von 20) (Englisch)

812408

Zoom out

Zoom in

Vorherige Seite

1/20

Nächste Seite

7. Special Functions

Used to set basic items and expanded functions.

The settings in this menu should only be changed by a specialist.

Pump settings V1/ Signal V1

In this menu, the settings for the speed controlled output V1 are executed.

Type of pump/ Type of signal

The type of speed controlled pump used can be set here.

0-10V: Control of special pumps (e.g. high efficiency pumps) through a 0-10V signal.

PWM: Control of special pumps (e.g. high efficiency pumps) through a PWM signal.

Pump/ Profile

In this menu, the preset profiles for the pump can be selected or under “manual” all settings can be done personally. The settings

can still be changed after a profile has been selected.

Output Signal

In this menu, the type of pump is set: heating pumps have the greatest output with a small input signal, solar pumps in contrast

have very little output with a small input signal. Solar = normal, heating = inverted.

PWM / 0-10V off

This signal / this voltage is emitted if the pump is turned off (pumps with cable break detection require a minimal voltage / a min-

imum signal).

PWM / 0-10V on

This voltage / this signal requires the pump in order to turn on and to run at a minimum speed.

PWM / 0-10V max.

With this value, the maximum voltage level / maximum frequency can be specified for the highest speed of the energy saving

pump, which is used, for example, during the flushing or manual operation.

Show signal

Represents the set pump signal in a graphic and text overview.

Speed control

If the speed control is activated, itSBMC offers the possibility through a special internal electronic system to change the speed of

pumps depending on the process.

This function should only be activated by a technician. Depending on the pump being used and the pump level, the

minimum speed may not be set too small, because the pump or the system may be damaged. The specifications from

the affected manufacturer must be observed for this! When in doubt, the min. speed and the pump level should be set

too high instead of too low.

Purging time

For this time, the pump runs with its full speed (100%) in order to guarantee a secure start-up. Only after expiration of this purging

time will the pump have a controlled speed and will switch, depending on the set variant, to the max. or min. speed. Speed.

Max. Speed

The maximum speed of the pump is determined here. During the setting, the pump runs in the respective speed and the flow can

be determined.

The specified percentages are variables, which may deviate more or less strongly depending on the system, pump

and pump level. 100% is the maximum possible power of the controller.

Min. Speed

The minimum speed of the pump is determined here. During the setting, the pump runs in the respective speed and the flow can

be determined.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Sorel SBMC Seite 16

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Sorel SBMC

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info