Bedienungsanleitung Soundcraft EFX (Seite 38 von 60) (Englisch)

611451

Zoom out

Zoom in

Vorherige Seite

1/60

Nächste Seite

Soundcraft EFX/EPM User Guide Issue 1210

USING YOUR EFX OR EPM CONSOLE

The nal output from your sound system can only ever be as good as the weakest

link in the chain, and especially important is the quality of the source signal be-

cause this is the starting point of the chain. Just as you need to become familiar

with the control functions of your mixer, so you must recognise the importance

of correct choice of inputs, microphone placement and input channel settings.

However, no amount of careful setting up can take account of the spontaneity

and unpredictability of live performance. The mixer must be set up to provide

“spare” control range to compensate for changing microphone position and the

absorption effect of a large audience (different acoustic characteristics from

soundcheck to show).

MICROPHONE PLACEMENT

Careful microphone placement and the choice of a suitable type of microphone

for the job is one of the essentials of successful sound reinforcement. The dia-

grams on the left show the different pick-up patterns for the most common types

of microphone. Cardioid microphones are most sensitive to sound coming from

in front, and hypercardioid microphones offer even greater directivity, with a small

amount of pickup behind the microphone. These types are ideal for recording

vocalists or instruments, where rejection of unwanted sounds and elimination

of feedback is important. The aim should be to place the microphone as close

as physically possible to the source, to cut out unwanted surrounding sounds,

allow a lower gain setting on the mixer and avoid feedback. Also a well chosen

and well placed microphone should not need any appreciable equalisation.

There are no exact rules - let your ears be the judge. In the end, the position

that gives the desired effect is the correct position!

INITIAL SETUP

Once you have connected up your system (see the sections on connection and

wiring earlier in this manual for guidance) you are ready to set initial positions

for the controls on your mixer.

Set up individual input channel as follows:

• Connect your sources (microphone, keyboard etc.) to the required in-

puts.

WARNING: Phantom powered mics should be connected before the +48V

is switched on. Ensure the PA system is OFF when switching phantom

power on or off.

• Set Master faders at 0, input faders at 0, and set power amplier levels

to about 70%.

• Provide a typical performance level signal and press the PFL button on

the rst channel, monitoring the level on the bargraph meters.

• Adjust the input gain until the meter display is in the amber section, with

occasional peaks to the rst red LED at a typical maximum source level.

This allows sufcient headroom to accommodate peaks and establishes

the maximum level for normal operation (but see note below).

• Repeat this procedure on other channels as required. As more channels

are added to the mix, the meters may move into the red section. Adjust

the overall level using the Master Faders if necessary.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Soundcraft EFX Seite 38

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info