Bedienungsanleitung Soundcraft EPM (Seite 11 von 60) (Englisch)

611452

Zoom out

Zoom in

Vorherige Seite

1/60

Nächste Seite

Soundcraft EFX/EPM User Guide Issue 1210

11 PEAK LED This is used to indicate that the signal is close to distorting (clipping) on a

specic channel.

12 INPUT CHANNEL FADER This is used to control the level fed to the Mix Bus and post-fade sends.

13 MIX OUTPUTS (XLR) & Connect these to your analogue recording device, or to your amplication

MONO OUT (¼” Jack) system.

14 MIX INSERTS (¼” Jack) This is a pre-fade break in the signal path which can be used to feed a

dynamics or mastering device. The signal is sent from the tip of the jack plug

and the return path comes back in on the ring of the jack plug.

15 MONITOR O/Ps (¼” Jack) These are used to feed your monitoring system. This can be directly connected

to powered monitors, or indirectly via an amplier to standard monitors.

16 MASTER FADERS These faders control the overall level of the mix outputs.

17 MAIN METERS These show the level of the mix outputs. When the PFL ACTIVE LED is lit, the

meters show the level of the selected PFL signal.

18 MONITOR CONTROL This controls the level of the signal sent to your monitoring system.

19 PHONES CONTROL This controls the level of the signal sent to the headphones jack socket.

20 AUX 1 OUTPUT (¼” Jack) This output can be used to send the channel signal to an artist’s monitors

(headphones/in-ear/stage monitors). It is switchable pre/post fade.

21 AUX CONTROL This switch globally switches the AUX1 feed on all the input modules to be

either pre or post-fade.

22 STEREO INPUTS (¼” Jack) These two inputs can be used to connect line level stereo inputs from key-

boards, sound modules, samplers, computer based audio cards etc. These

inputs pass through a normal channel strip, with EQ, Auxes and a Balance

control.

23 2-TRACK INPUTS Here you can connect the playback from your recording device.

(RCA Phono)

24 2-TRACK CONTROLS Use these to control the 2 Track signal. The MONITOR switch sends the signal

to the monitor outputs and phones, whilst the TO MIX switch sends it to the

main mix.

25 RECORD OUTPUTS You can connect these to the inputs of your recording device.

(RCA Phono)

26 PHANTOM POWER Press this to switch the phantom power (48V) on for condenser microphones.

WARNING: Do Not apply Phantom Power before connecting a

microphone.

27 HEADPHONES (¼” Jack) Plug your headphones into this socket. Recommended headphones imped-

ance is 150 ohms or greater.

28 STEREO RETURN INPUTS This pair of inputs accept 3-pole ‘A’ gauge (TRS) jacks. Use these inputs for

sources such as keyboards, drum machines, synths or CDs. The inputs are

BALANCED. Mono sources may be used by plugging into the left jack only.

29 STEREO RETURN CONTROL This control sets the level of signal routed to the main mix busses. There is

an associated PK LED to warn of signals which are too high.

30 FX BUS OUTPUT This output carries the signal from the FX bus. It could be used as a second

Aux Output if desired, if the FX Processor is not needed at the time. The FX

sends on the inputs channels to the FX bus are always post-fade.

31 FOOTSWITCH CONNECTOR This is used by the FX Processor, see page 26.

32 LEXICON® FX PROCESSOR See the information starting on page 27

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Soundcraft EPM Seite 11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info