Bedienungsanleitung Soundcraft FX 16ii (Seite 10 von 48) (Englisch)

611476

Zoom out

Zoom in

Vorherige Seite

1/48

Nächste Seite

WIRING UP

Mic Input

The MIC input accepts XLR-type connectors and is designed to suit a wide

range of BALANCED or UNBALANCED low-level signals, whether from delicate

vocals requiring the best low-noise performance, or drum kits needing

maximum headroom. Professional dynamic, condenser or ribbon mics are

best because these will be LOW IMPEDANCE. While you can use low-cost

HIGH IMPEDANCE mics, you do not get the same degree of immunity to

interference on the microphone cable and as a result the level of background

noise may be higher. If you turn the PHANTOM POWER on, the socket provides

a suitable powering voltage for professional condenser mics.

The input level is set using the input GAIN knob.

The LINE input offers the same gain range as the MIC input, but at a higher

input impedance, and is 20dB less sensitive. This is suitable for most line

level sources.

Line Input

Accepts 3-pole 6.35mm (1/4") jacks, or 2-pole mono jacks which will

automatically ground the ‘cold’ input. Use this input for sources other than

mics, such as keyboards, drum machines, synths, tape machines or DI boxes.

The input is BALANCED for low noise and immunity from interference, but you

can use UNBALANCED sources by wiring up the jacks as shown, although

you should then keep cable lengths as short as possible to minimise

interference pick-up on the cable. Note that the ring must be grounded if the

source is unbalanced. Set the input level using the GAIN knob, starting with

the knob turned fully anticlockwise. Unplug any MIC connection when using

the LINE input.

Insert Points (Input Channels, Mix Outputs and Sub Outputs)

The unbalanced insert point is a break in the signal path, allowing limiters,

compressors, special EQ or other signal processing units to be added in the

signal path. The Insert is a 3-pole 6.35mm (1/4") jack socket which is

normally bypassed. When a jack is inserted, the signal path is broken.

The signal from the insert point appears on the TIP of the plug and is returned

on the RING, with the sleeve as a common ground.

On Input Channels, the Send may be tapped off as an alternative pre-fade,

pre-EQ direct output if required, using a lead with tip and ring shorted together

so that the signal path is not interrupted.

WARNING !

Start with the input GAIN knob turned fully anticlockwise when

plugging high level sources into the LINE input to avoid

overloading the input channel or giving you a very loud surprise!

DO NOT use UNBALANCED sources with the phantom power

switched on. The voltage on pins 2 & 3 of the XLR connector may

cause serious damage. BALANCED dynamic mics may normally be

used with phantom power switched on (contact your microphone

manufacturer for guidance)

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Soundcraft FX 16ii Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Soundcraft FX 16ii

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info