Bedienungsanleitung Soundcraft FX 16ii (Seite 25 von 48) (Englisch)

611476

Zoom out

Zoom in

Vorherige Seite

1/48

Nächste Seite

(essentially the tail of the reverb) heard first, and then grows louder over time until they abruptly cut off.

Ambience Reverb

Ambience is used to simulate the effect of a small or medium sized room without noticeable decay. It is often

used for voice, guitar or percussion.

Studio Reverb

Much like Room reverb, Studio produces an excellent simulation of smaller, well controlled acoustic spaces,

characteristic of the main performance areas in recording studios. Studio is also useful with dialog and

voiceover applications as well as individual instrument and electric guitar tracks.

Arena Reverb

Arena reverb emulates a huge physical space such as an indoor sports venue or stadium. The characteristics

of Arena reverb are long secondary reflection times and a reduced amount of high frequency content. Arena

is a mostly mid- and low frequency dominant reverb, and is an ideal selection for “special effect” type

applications that require extremely long reverb times. It is not a good choice for a very busy mix, since it can

reduce intelligibility.

Spring Reverb

A Spring reverb is created by a pair of piezoelectric crystals—one acting as a speaker and the other acting as

a microphone— connected by a simple set of springs. The characteristic ‘boing’ of a spring is an important

component of many classic rock and rockabilly guitar sounds.

REVERB CONTROLS

Pre Delay

Creates an additional time delay between the source signal and the onset of reverberation. This control is not

intended to precisely mimic the time delays in natural spaces, as the build-up of reverberation is gradual, and

the initial time gap is usually relatively short. For the most natural effect, the Pre Delay values should be set

in the range of 10-25 milliseconds. However, if a mix is very busy or overly cluttered, increasing the Pre Delay

time may help clarify it, and set each instrument apart from each other.

Decay

Controls the amount of time the reverb can be heard. Higher settings increase reverberation times which are

usually associated with larger acoustical environments, but can decrease intelligibility. Lower settings shorten

reverb times and should be used when a smaller apparent space or a more subtle effect is desired.

Liveliness

Adjusts the amount of high frequency content in the reverberation tails. Higher settings increase high frequency

response, creating brighter reverbs; lower settings create darker reverbs with more bass frequency emphasis.

Diffusion

Controls the initial echo density. High settings of Diffusion result in high initial echo density, and low settings

cause low initial density. In a real-world situation, irregular walls cause high diffusion, while large flat walls

cause low diffusion. For drums and percussion, try using higher Diffusion settings.

Shape

This control helps give a sense of both room shape and room size. Low values for Shape keep the majority of

sound energy in the early part of the reverb tail. High values move the energy to later in the reverb, and are

helpful in creating the sense of a strong rear wall or “backslap.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Soundcraft FX 16ii Seite 25

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Soundcraft FX 16ii

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info