Bedienungsanleitung Soundcraft LX 7ii (Seite 25 von 32) (Englisch)

611475

Zoom out

Zoom in

Vorherige Seite

1/32

Nächste Seite

HF EQHF EQ

HF EQ

Turn clockwise to boost high (treble) frequencies (12kHz and above) by up to 15dB,

adding crispness to cymbals, vocals and electronic instruments. Turn anticlockwise to

cut by up to 15dB, reducing hiss or excessive sibilance which can occur with certain

types of microphone. Set the knob in the centre-detented position when not required.

MID EQ (HMID & LMID)MID EQ (HMID & LMID)

MID EQ (HMID & LMID)

There are two pairs of knobs which work together to form HI and LO MID frequency EQ

sections. The lower knob in each pair provides 15dB of boost and cut, just like the HF

EQ knob, but the frequency at which this occurs can be set by the upper knob over a

range of 550Hz to 13kHz (HMID) or 80Hz to 1.9kHz (LMID). This allows some truly

creative improvement of the signal in live situations, because the mid bands cover the

range of most vocals. Listen carefully as you use these controls together to find how

particular characteristics of, for instance, a vocal signal can be enhanced or reduced.

Set the gain (lower) knob to the centre-detented position when not required. Note: Q

is set at 1.5.

LF EQLF EQ

LF EQ

Turn clockwise to boost low (bass) frequencies (60Hz and below) by up to 15dB,

adding warmth to vocals or extra punch to synths, guitars and drums. Turn anticlockwise

to cut low frequencies by up to 15dB for reducing hum, stage rumble or to improve a

mushy sound. Set the knob to the centre-detented position when not required.

0 - EQ S0 - EQ S

0 - EQ S

WITWIT

WIT

CHCH

The EQ switch bypasses the Equalisation section when released. Alternately pressing

and releasing the switch provides an easy way of comparing the equalised and

unequalised signals.

1 - A1 - A

1 - A

UX SENDSUX SENDS

UX SENDS

These are used to set up separate mixes for FOLDBACK, EFFECTS or recording, and the

combination of each Aux Send is mixed to the respective Aux Output at the rear of the

mixer. For Effects it is useful for the signal to fade up and down with the fader (this is

called POST-FADE), but for Foldback or Monitor feeds it is important for the send to be

independent of the fader (this is called PRE-FADE). All Aux Sends are muted with the

other channel outputs when the MUTE switch is pressed.

All six Aux Sends are POST-EQ, unless the EQ is bypassed using the EQ switch (see

above) and are normally POST-FADE for use as effects sends or additional submixes.

Aux’s 1 & 2 and 3 & 4 may if required be switched in pairs to PRE-FADE by pressing

the respective PRE switch, for use as foldback or monitor feeds. Aux’s 5 & 6 always

remain POST-FADE.

2 - P2 - P

2 - P

ANAN

This control sets the amount of the channel signal feeding the Left and Right MIX

buses, allowing you to move the source smoothly across the stereo image. When the

control is turned fully right or left you are able to route the signal at unity gain to either

left or right outputs individually.

3 - MUTE3 - MUTE

3 - MUTE

All outputs from the channel except inserts are active when the MUTE switch is released

and muted when the switch is down, allowing levels to be pre-set before the signal is

required.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Soundcraft LX 7ii Seite 25

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Soundcraft LX 7ii

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info