Bedienungsanleitung Soundcraft M Series (Seite 23 von 48) (Englisch)

611444

Zoom out

Zoom in

Vorherige Seite

1/48

Nächste Seite

USER GUIDE

MASTER SECTION

PHANTOM POWER

Many professional condenser mics need PHANTOM POWER, which is a method of sending a powering

voltage down the same wires as the mic signal. Press the switch to enable the +48V power to all of the

MIC inputs. The adjacent LED illuminates when the power is active.

WARNING: TAKE CARE when using unbalanced mics which may be damaged by the phantom

power voltage. Balanced dynamic mics can normally be used with phantom power switched

on (contact your microphone manufacturer for guidance)

Mics should always be plugged in, and all output faders set to minimum before switching

the Phantom Power ON to avoid damage to external equipment

POWER INDICATOR

This LED lights to show when power is connected to the console.

BARGRAPH METERS

The three-colour peak reading BARGRAPH METERS normally show the level of the MIX RIGHT and MIX LEFT

outputs, giving you a constant warning of excessive peaks in the signal which might cause overloading. Aim

to keep the signal just touching the red segments at peak levels for best performance.

Similarly, if the output level is too low and hardly registering at all on the meters, the level of background

noise may become significant. Take care to set up the input levels for best performance.

When any PFL switch is pressed, the meters switch to show the selected PFL signal on both meters, in

mono.

PLAYBACK

The rotary control sets the level of the 2 Track Tape input, which is routed to the headphones, monitor

outputs and meters. These inputs, on RCA phono connectors are an ideal way to connect the playback of a

tape machine for monitoring.

PLAYBACK REPLACES MIX

Press this switch to replace the MIX Left/Right signal at the MIX outputs with the Playback signal connected

to the Left and Right RCA sockets

(see also p.22).

PLAYBACK PFL

Press this switch to route the Playback signal to the monitor and phones, over-riding the default monitor/

Phones signal. This listening point is before the PB LEVEL control, so material can be previewed before being

routed.

MONITOR LEVEL

This control sets the level to the MONITOR LEFT & RIGHT outputs. If headphones are plugged into the

PHONES jack, the headphone level will track the Monitor Level.

PHONES LEVEL

This control sets the output level to the Headphone outputs. If headphones are plugged into the PHNS jack,

then the knob sets a comfortable headphone listening level without affecting the Monitor output levels.

AUX MASTERS

Each Aux output has a master output level control and associated AFL switch.

AUX AFLS

Just like the PFL switches on the channels, you can monitor each AUX output by pressing the AFL switch.

This routes the AUX output signal to the MONITOR or PHONES, replacing the MIX signal. The METERS also

switch from the MIX to display the PFL/AFL signal and the PFL/AFL LED lights to warn that a PFL or AFL

switch is pressed. When you release the switch, the Monitor swaps back to the MIX.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Soundcraft M Series Seite 23

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Soundcraft M Series

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info