Bedienungsanleitung Soundcraft MFX12 (Seite 25 von 48) (Englisch)

611455

Zoom out

Zoom in

Vorherige Seite

1/48

Nächste Seite

FX PROCESSOR CONTROLS

1. Tempo Button - Tapping this button twice sets the Delay Time of the selected program.

The LED flashes to indicate current tempo. Can be tapped in time with music source to

synchronise the delay.

2. Store Button - Stores program modifications to one of the program locations. Press

and hold for three seconds will store the preset in the current location. The LED will flash

rapidly during the store operation and then stay illuminated for 1 second to show the

operation is complete.

3. Pre Delay / Time/ Speed Knob - Controls Pre Delay of the reverbs or the first param-

eter (time or speed related) of the selected effect. The LED illuminates when the param-

eter matches the stored setting.

4. Decay / Feedback/Depth Knob - Controls Decay of the reverbs or the second pa-

rameter (feedback or depth related) of the selected effect. The LED illuminates when the

parameter matches the stored setting.

5. Variation - Controls Liveliness or Diffusion (depending on the reverb selected) or the

third parameter of the selected effect. The LED illuminates when the parameter matches

the stored setting.

6. Program Select Knob - Navigates through programs, turning to the required program

will initiate the loading of the program which take approximately 1 second. The knob can

be rotated clockwise or anticlockwise and will alternate between BANK A and BANK B

every full rotation. The current bank is shown by its illuminated LED, which flashes if the

FX processor is muted. There is a handy aide memoir of the programs printed on the

front panel.

7. Clip LED – This LED illuminates when either the incoming audio or the processed

audio (within the effect processor) overloads, and causes distortion of the signal.

Footswitch Input (not shown on diagram, see item 29 on page 20) - Using a single

pole, momentary footswitch inserted into the FOOTSWITCH input the effects processor

can be muted/un-muted.

PFL (not shown on diagram, see item 27 on page 20)- This switch routes a post-effects

processor, pre-fade (EFFECTS FADER) signal to the monitor system.

8. MUTE - This switch mutes the output of the FX processor. It doesn’t mute the PFL signal or the FX TO AUX

1 pre-fade signal.

9. FX TO AUX 1 - This pot routes a pre-fade and a post-fade signal to the Aux 1-pre and Aux 1-post busses

respectively.

10. FX TO AUX 2- This pot routes a pre-fade and a post-fade signal to the Aux 2-pre and Aux 2-post busses

respectively.

11. EFFECTS FADER - This fader controls the level of the signal, from the FX processor, routed to the main

mix busses.

FX BUS OUT (not shown on diagram, see item 28 on page 20) - This output carries the signal from the FX

bus. It could be used as a third Aux Output if desired.

12. ‘SP’ LED - This indicates when a signal is present.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Soundcraft MFX12 Seite 25

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info