Bedienungsanleitung Soundcraft MPMi (Seite 40 von 60) (Englisch)

611474

Zoom out

Zoom in

Vorherige Seite

1/60

Nächste Seite

38 Soundcraft MFXi MPMi User Guide Issue 1210

DELAY CONTROLS

Time Range

Controls the length of the delay relative to Tap Tempo. At the 12 o’clock position, delay repeats are synchro-

nous with the Tempo light (represented by a Quarter Note); lower values create faster repeats, higher values

increase the time between repeats. Range 0-72. See the Effects Data Chart for exact note values.

Feedback

Controls the number of delay repeats by feeding the delay output signal back into the delay input. This creates

a series of delay repeats, each slightly attenuated until they become inaudible. Higher settings create more

repeats; lower settings reduce the number of repeats. When this knob is turned fully clockwise, it engages

Repeat Hold – delay repeats play back in an innite loop, but no further input signal is introduced into the

delay effect. Repeat Hold is available only on Studio, Digital and Pong Delay.

Ducker Threshold

Studio and Digital delays offer a “ducking” feature, which causes the delay repeats to attenuate (or get softer)

by -6dB when live (or input) signal is present. This allows the delay to remain as an effect, and not clash with

the original signal. The higher this value is set, the louder an input signal must be for the ducking to take place.

Smear

This parameter controls the amount of “smear,” or signal degradation and frequency loss. Particularly evident

in the Tape Delay, the higher the setting, the more each delay repeat loses intelligibility compared to the

original signal.

Tap Ratio

Tap Ratio sets the length between the rst and second tap repeats of the Pong Delay. With this control set

at 12 o’clock, repeats are evenly alternated between left and right channels. As this knob is turned counter-

clockwise, the rst tap occurs earlier and the second tap occurs later than they did at the 12 o’clock position.

When the knob is turned clockwise, the rst tap occurs later and the second tap occurs earlier.

Depth

This controls the intensity of modulation, or “depth” in the Modulated Delay. Lower settings produce a more

subtle effect, while higher values give a more “seasick” feeling.

Tempo Button

Tapping this button twice sets the delay times. The Tempo button LED ashes the tempo tapped in, and delay

taps will be synchronized to the ashing LED. Use the Time Range knob to increase or decrease delay times

after tapping in a tempo.

Note: When Delay Feedback is at maximum (fully clockwise) in some programs the mode changes to hold

the audio in a constant loop. This is indicated in the Effects Data Chart as “+H”.

MODULATED EFFECTS

Chorus

Chorus creates a lush, full sound by combining two or more signals together where one is unaffected and the

other signals vary in pitch very slightly over time. Chorus is commonly used to fatten up tracks and to add body

to guitars without coloring the original tone. Chorus can also be used with discretion to thicken a vocal track.

Knob 1: Speed Controls the modulation rate of the Chorus effect. Lower settings are subtle, while higher

values are much more pronounced.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Soundcraft MPMi Seite 40

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Soundcraft MPMi

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info