Bedienungsanleitung Soundcraft Vi 3000 (Seite 104 von 202) (Englisch)

611458

104

Zoom out

Zoom in

Vorherige Seite

1/202

Nächste Seite

Vi3000 USER MANUAL

11.1 11.1: SOLO > PRIMARY BEHAVIOUR

11.0: SOLO System

AFL, PFL and SIP

The solo system on the Soundcraft Vi3000™ comprises a non-destructive PFL and AFL Solo capability from Inputs

and Outputs, and also the option of a destructive Solo-In-Place mode, for use only during soundchecks or rehearsals.

Solo-In-Place mode has to be enabled from within the Monitor Setup and changes the mode of operation of the Solo

System. It is automatically cancelled if the Monitor Setup screen is closed, to ensure that it cannot accidently be left

on.

PFL and AFL Soloing (SIP Mode OFF)

• Soloing a single Input locally generates a PFL or AFL Solo onto the Solo Bus, depending on the mode selected in the

Monitor Setup page (default is AUTO, see next point).

• If the Input Solo Mode is set to AUTO in the Monitor Setup page, soloing more than one Input locally (by pressing

and holding the rst Solo/Sel switch then pressing others, or switching off AUTO CANCEL mode) will generate an AFL

Solo onto the Solo Bus from all soloed Inputs. If a single output is soloed, the solo will be PFL.

• The PFL feed from Mono Inputs is taken after the channel Pan control so the signal heard on the Monitor outs will

reect the Pan setting. If the Input is a Stereo Input, the PFL feed is left channel to left Solo Bus, right to right.

• The AFL feed from Mono or stereo (paired) Inputs is stereo and follows the channel Pan.

• Soloing an Output (either locally or via a VCA Master Solo) generates an AFL or PFL Solo, depending on the mode

selected in Monitor Setup (default is AFL for outputs).

The post-fade Output signal is switched onto the Solo Bus.

• In all cases when SIP Mode is OFF, operation of any Solo will switch the audio onto the Solo Bus and the Monitor

section will be automatically switched so that the Solo audio replaces the previous monitor source selection (if any)

assuming that IN Solo and/or OUT Solo have been selected as a Monitor Source in the Monitor Setup Page.

Solo-In-Place Soloing (SIP mode ON)

• Soloing an Input generates a ‘destructive’ SIP Solo, actually muting or dimming all other Inputs which are not Soloed

or set to Mute Safe, as if you had pressed their channel ON switches. Other channels which are subsequently soloed

will be unmuted. The amount of dimming is controlled by the SOLO BLEND control on the front panel.

• Soloing an Input (or group of Inputs) by soloing a VCA Master that the input is assigned to, generates a SIP Solo on

all Inputs in the VCA Group.

* The Input signal is not switched onto the Solo Bus, and the Monitor section does not switch the Solo Bus audio to

override the monitor source selection (you hear the soloed signal(s) via the Master LRC busses directly.

• Soloing an Output generates a normal Output AFL or PFL Solo (according to the mode selection made in Monitor

Setup), the same as if SIP Mode was OFF. The Output signal is switched onto the Solo Bus and the Monitor section

switches so that the Output

Solo audio is heard on the Monitors, replacing the previous monitor source, if any.

SOLO SYSTEM BEHAVIOUR

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Soundcraft Vi 3000 Seite 104

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info