Bedienungsanleitung Soundcraft Vi 3000 (Seite 111 von 202) (Englisch)

611458

111

Zoom out

Zoom in

Vorherige Seite

1/202

Nächste Seite

4.3: INPUT CHANNEL > DYNAMICS

Vi3000 USER MANUAL

4.3 INPUT CHANNEL > De Esser

Vi3000 USER MANUAL

13.1 13.1: EDIT > COPY, PASTE, UNDO

13.1: EDIT > COPY, PASTE, UNDO

13.1: Copy, Paste, Undo

Ranges of channels or busses, individual channels or busses, processing blocks (eg EQ), or even individual param-

eters (eg mic gain control) within a processing block can be copied to the clipboard then pasted to another channel,

block, or range. This includes the console’s internal Lexicon FX units.

The last paste operation can be quickly reversed with the UNDO function.

Copy Options

• Put the console into Copy mode.

• Copy A Channel Or Bus Master

In copy mode, select or deselect a full input channel or output bus by pressing its [SEL] Key. Select a range by holding

the [SEL] Key of the rst Channel and pressing [SEL] of the last Channel. When a whole channel or range of channels

are selected, the grey Channel border is replaced with a yellow border.

Some parameters or process blocks are not included with a channel or bus copy by default, but most can be added

to the copy by selecting them individually (see below). The only ones that CANNOT be added are the Insert Point and

Direct Output settings.

Parameters not included with a whole input channel copy but that CAN be added individually are: Input 1/2 switch,

Input 1 & 2 patch, Mic Input Gain and all associated switches (48V, PAD, Phase Inv etc), Fader and Mute, VCA & Mute

Group Assignment, FX settings.

Parameters not included with a whole bus copy but that CAN be added individually are the output patch and FX set-

tings.

• Copy A Block

Select or deselect a function block by touching that block’s Touch eld. Indication that a whole function block is select-

ed is shown with a wide yellow indicator in the top left corner of the eld.

• Copy A Paramter

Select a single parameter by touching the corresponding Rotary encoder or by pressing the small key to the left of the

encoder. To make access to parameters easy while in Copy mode, enter the ‘Zoom’ mode with a long press on a touch

eld. Alternatively you can enter the Zoom mode, before you activate Copy mode by pressing the touch eld in the

normal way and entering Copy mode.

A selected parameter is indicated with yellow text in the Parameter Label. Note that not all parameters can be selected

individually; in some cases a set of parameters will automatically be selected when one of the set is touched.

If only a set or a single Parameter from within a block is selected then a small yellow indicator is displayed.

Copy, Paste,

and Undo Active

Put the console into

Copy mode.

Used for selecting channels, processing blocks, and

parameters and copying them to the clipboard. In copy

mode, the console [SEL] keys illuminate in blue to indi-

cate their function as selects rather than as Solos.

Copy Mode

Active

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Soundcraft Vi 3000 Seite 111

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info