Bedienungsanleitung Soundmaster UR8100 (Seite 10 von 56) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Schwedisch, Finnisch)

674318

Zoom out

Zoom in

Vorherige Seite

1/56

Nächste Seite

UR8100 / English Instruction Manual

ALARM SETTING

SETTING THE ALARMS (ALARM 1 and ALARM 2)

Be sure to observe the PM indicator when setting the alarm to make sure the alarm time is set

correctly for AM or PM. If the PM Indicator is ‘On’, the alarm time will be afternoon/night time. The

setting sequence for AL1 is as follows :

Normal Time → ALARM 1 Hour → ALARM 1 Minute → Normal Time

1. Tap the “ALARM 1” (or “ALARM 2” ) button (1 or 2) to show the preset alarm time.

2. Press and hold the “ALARM 1” (or “ALARM 2”) button (1 or 2) again for about 2 seconds until

the Hour Indicator on the LED DISPLAY flashes. Press the “<<” (3) or “>>” (4) button to obtain

the desired Alarm Hour.

3. Tap the “ALARM 1” (or “ALARM 2”) button (1 or 2) again to advance to the Minute Indicator.

Press the “<<” (3) or “>> “(4) button to obtain the desired Alarm Minutes.

4. Press the “ALARM 1” (or “ALARM 2”) button (1 or 2) to finish setting and exit to normal time

display.

5. To disable ALARM (or ALARM 2) from automatically sounding on the upcoming days, press

and hold the “ALARM 1” (or “ALARM 2”) button (1 or 2) for about 2 seconds, the corresponding

ALARM 1 (or ALARM 2) INDICATOR will go off.

6. To resume ALARM 1 (or ALARM 2) from automatically sounding on the upcoming days, press

and hold the “ALARM 1” (or “ALARM 2”) button (1 or 2) for about 2 seconds, the corresponding

ALARM 1 (or ALARM 2) INDICATOR will turn on and the alarm will sound the following day at

the set time.

TURNING OFF THE ALARM

When the preset alarm time is reached, the ALARM 1 (or ALARM 2) INDICATOR will flash on the

LED DISPLAY and the beeper alarm will sound for 30 minutes unless interrupted by pressing

“SNOOZE” (7). To stop the alarm immediately, tap the corresponding “ALARM 1” (or “ALARM 2”)

button (1 or 2). The alarm will ring again at the same alarm time on the following day, or when set to

go off based on your Alarm settings.

Notes :

 When the Beeper alarm begins, it will sound at a lower beeping rate and gradually increase to

the normal rate within 30 seconds.

SNOOZE FUNCTION

When the alarm source is sounding, press the “SNOOZE” (7) button to suspend the alarm and

activate the snooze function. The Alarm will temporarily stop and sound again 9 minutes later but

the ALARM 1 (or ALARM 2) indicator will keep flashing.

Notes:

This manual snooze operation can be repeated again and again.

To turn off the snooze function before it ends, tap the corresponding “ALARM 1” (or

“ALARM 2”) button (1 or 2). The ALARM 1 (or ALARM 2) INDICATOR will stop flashing.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Soundmaster UR8100 Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info