Bedienungsanleitung Sparky BAR 12E (Seite 9 von 86) (Deutsch, Englisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch)

604125

Zoom out

Zoom in

Vorherige Seite

1/86

Nächste Seite

Original instructions EN





When using your cordless angle drill/driver continuously,

the batteries in your battery pack will become hot. You

should let a hot battery pack cool down for approximately

-

tery pack becomes discharged and is hot, the red light

   

down, the red light will glow continuously to indicate fast

charging mode, 1-hour charge time.

 This will occur when continuous use of your tool

causes the battery pack to become hot. It does not occur

under normal conditions.

VII - Know your product





3. Keyless chuck

4. Torque control collar

5. Battery



7. LED charge indicator

VIII - Operation



1. When the trigger switch is depressed, the tool rotates.

Fig. 4

2. The rotation speed can be controlled by varying the

pressure on the trigger switch. Light pressure on the

trigger switch results in low rotation speed, further

pressing results in smooth increase of the rpm to

maximum upon reaching the extreme position.



WaRning: Switch off the power tool prior to

any procedure on it. To avoid involuntary switching on

we recommend removing the battery pack.

Grip rear collar of keyless chuck and rotate front collar

until chuck is opened sufficiently for the bit to be inserted.

Then firmly tighten front collar by hand. Ensure that the

bit is firmly fastened.

To remove a bit, rotate the front chuck collar.



Install the bit that matches the screw, line up the bit in the

grooves of the head of the screw then tighten it.

Push the driver just enough to keep the bit fitting the

head of the screw.

WaRning: Over tightening can result in the

screw breaking or damage to the end of the driver bit.

1. Applying this power tool for too long, shall tighten the

screw excessively and break it.

2. If the machine is held at an angle to the screw being

tightened, the head of the screw may be damaged,

or the specified torque may not be transmitted to the

screw. Always keep the unit and the screw being tight-

ened in a straight line.



-

ing the R-side of the push button. The L-side of the

push button is pushed to turn the bit counter-clockwise.

Fig. 5

WaRning: The push button can not be

switched while the drill is turning. To switch the push

button, stop the machine and then set the push button.



By rotating the torque control collar behind the chuck,

you can adjust the torque to each of the 12 settings.

Fig. 6

The range of 12-torque setting allows better control

when using the drill as screwdriver as it prevents over

tightening of the screws.



1. Open the chuck jaws entirely.



between jaws to engage the left-threaded screw head.

Remove screw by turning clockwise.

3. Place the hex key in the chuck and tighten. Using a wood-

en mallet or similar object, strike the hex key sharply in

counter-clockwise direction. This will loosen the chuck so

it can be unscrewed by hand.

IX - Maintenance

cleaning

 

vents with dry air at least once a week. Wear safety

glasses while performing this.

         

cloth and mild detergent.

WaRning: Although exterior plastic parts

are highly solvent resistant, NEVER use solvents.



 

the charger using a cloth or soft non-metallic brush.

Do not use water or any cleaning solutions.

WaRning: Disconnect the charger from the

AC outlet before cleaning.

Sparky BAR 12E Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info