Bedienungsanleitung Sparky BBK2 1500 (Seite 11 von 114) (Deutsch, Englisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch)

604126

Zoom out

Zoom in

Vorherige Seite

1/114

Nächste Seite

Original instructions

Switch on the PRCD. Turn on switch (1). Proceed to

drill.

Control the proper position of the machine using the

built-in level (3).

WARNING: Do not touch the core bit or the

machined surface near it immediately after operation.

They may be very hot and may cause skin burns.

13. Apply gentle pressure during operation. Excessive

pressure may damage the machine or the core bit.

14. If pieces of the material are broken into the drilled

opening, take out the core bit from the material and

remove the pieces.

15. Release switch (1) to stop drilling.

1 6. Unplug the machine.

17. Close the tap and disconnect the machine from the

water feed system.

18. Remove the diamond core bit and the adapter (9).

WET DRILLING ON A DRILL STAND

1. Attach the drill stand SP 60 stationary on a solid at

surface as described in SP 60 manual.

2. Mount the machine on the drill stand. (Read SP 60

manual.)

3. Mount a diamond core bit and tighten it gently by

hand.

4. Couple the water feed system.

5. Plug the machine into the socket.

6. Select suitable speed.

7. To switch the machine to continuous use, press

switch (1) and in pressed position lock it by button (2).

8. Using the drill stand lever slowly move the diamond

core bit to the surface and start to drill carefully.

Adjust the water feed so that steady ow of water

ushes the core bit segments.

9. Apply constant gentle pressure during operation.

Excessive pressure may damage the machine or

core bit.

10. Upon completing of work using the lever pull out the

core bit.

11. Switch off the machine.

12. Turn off the water supply.

13. Unplug the machine.

14. Remove the diamond core bit.

15. Disassemble the machine from the drill stand.

ACCESSORIES

Auxiliary handle, water feed system, adapter, set of

spanners.

Maintenance

WARNING: Always ensure that the tool is

switched off and unplugged before attempting to

perform inspection or maintenance.

GENERAL INSPECTION

Regularly inspect all fasteners and ensure they are

properly tightened. Should any of the screws be loose,

retighten it immediately to avoid hazards.

If the replacement of the supply cord is necessary, this

has to be done by the manufacturer or his agent in order

to avoid a safety hazard.

CLEANING

For safe operation always keep the machine and its

ventilation slots clean.

Regularly check to see if any dust or foreign matter has

entered the ventilation slots and the grills around the

switches. Use a soft brush and/or air jet to remove any

accumulated dust. Wear safety glasses to protect your

eyes whilst cleaning.

Exterior plastic parts may be cleaned with a damp cloth

and mild detergent if necessary.

WARNING: Never use alcohol, petrol or other

cleaning agent. Never use caustic agents to clean

plastic parts.

IMPORTANT! To assure product safety and reliability,

repairs, maintenance and adjustment (including brush

inspection and replacement) should be performed

by certied service centres or other qualied service

organisations, always using genuine replacement parts.

pages-BBK2[3]1500.indd 9 9.7.2014 г. 10:22:52 ч.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Sparky BBK2 1500 Seite 11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info