Bedienungsanleitung Sparky HAG 2000ED (Seite 7 von 74) (Deutsch, Englisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch)

583074

Zoom out

Zoom in

Vorherige Seite

1/74

Nächste Seite

Original instructions

HEAT SETTINGS

Prior operation we recommend testing the appropriate

temperature on a scrap piece of material.

HAG 2000

The air ow temperature at the nozzle in position I of

switch (6) is 60°C. Please note that upon commutation

from position II or III to position I of the switch a certain

period is necessary for the temperature to drop to 60°C.

HAG 2000E (Fig. 1)

The air ow temperature at the nozzle in position I of

switch (6) is 60°C. Please note that upon commutation

from position II or III to position I of the switch a certain

period is necessary for the temperature to drop to 60°C.

In addition to the 3-stage air ow control, the tempera-

ture can be adjusted in the range 60°C to 550°C by ro-

tating the temperature regulator (5a) in direction „–“ for

decreasing or „+“ for increasing it.

HAG 2000ED (Fig. 1a)

The air ow temperature at the nozzle in position I of

switch (6) is 50°C. Please note that upon commutation

from position II or III to position I of the switch a certain

period is necessary for the temperature to drop to 50°C.

The air ow temperature change is shown on the display

(7) by blinking arrows ▲ or ▼. Upon reaching the target

temperature the arrows disappear and the display shows

the actual temperature.

In addition to the 3-stage air ow control, the tempera-

ture can be adjusted by buttons (5) in the range 70°C to

600°C. The necessary temperature can be set in steps

10°C each by pressing the left “–” button for decreas-

ing or the right “+” button for increasing the tempera-

ture. Brief pressing a button changes the temperature

by 10°C. Prolonged pressing a button changes the tem-

perature continuously by 10°C steps until reaching the

target temperature.

The hot air gun features double overheat protection:

- Upon misuse of the appliance a temperature sensor

switches the heater automatically, the fan keeps on

working.

- Upon overloading the appliance (restriction of the

air ow) the overheat protection switches off the

machine.

STATIONARY USE (FIG. 2)

Set the tool down on its rear in an upright position.

Make sure the surface is clean and dust free; polluted air

damages the motor.

Make sure the air stream is directed away from you.

Secure the cord to prevent pulling down the tool.

Do not touch the nozzle.

WARNING: Be especially careful when work-

ing with the upright unit! There is danger of burning on

the hot nozzle and the hot air stream.

Make sure nothing drops into the nozzle.

Carefully hold the tool with one hand while switching it

off with the other hand, and then allow it to cool down.

OPERATION IN CONFINED AREAS

For operation in conned areas the heat protector (2) can

be removed.

WARNING: Keep your hands away from the

hot nozzle. Beware of the increased risk of burns.

To remove the heat protector (2), switch off the machine

and let it cool down. Turn the heat protector clockwise

viewed from the display to remove it.

WARNING: When operating the machine with

the heat protector removed there exists increased risk

of re.

MOUNTING / REMOVING ACCESSORIES

Mounting: Place the corresponding nozzle onto the air

outlet.

Removing: Pull out the nozzle after it has completely

cooled down.

WARNING: Replacing the nozzle can be per-

formed only when it is cold, the switch is in position O

and the machine is unplugged.

The hot air gun is delivered with 4 nozzles for different

applications.

Reduction nozzle (8): This nozzle directs a concentrat-

ed heat ow to the workpiece. It is ideal for use when re-

moving paint in awkward corners, crevices, mouldings,

beading, architraves or whenever precise paint removal

is required.

Glass protection nozzle (9): This nozzle deects the

heat away from glasses or other fragile areas and back

onto the workpiece.

Reector nozzle (10): This nozzle disperses the heat

ow evenly around the whole workpiece. It is ideal for

defrosting water pipes, soldering pipework, bending

plastics and heat-shrinking electrical parts.

Flat nozzle (11): This nozzle directs a long narrow heat

pattern to the workpiece, and it is ideal for use when re-

moving paint or lacquer from larger at surfaces such as

skirting boards doors, stairs etc. It should be used in con-

junction with a at scraper.

APPLICATION EXAMPLES

Removing paint and lacquer (Fig. 3)

Hold the gun with the nozzle (11) approximately 50 mm

from the surface of the paintwork and start at the lower

heat setting to move it slowly backwards and forwards

until the paint blisters and bubbles. Keep a 30° to 40°

angle between the tool and the workpiece. Immediately

remove the paint with the scraper (12) or putty knife, oth-

erwise the paint will harden again. To avoid ignition clean

immediately the paint and the particles from the tool.

Whenever possible strip the paint along the wood bres.

Aim to heat the paint just ahead of the scraper so that you

pages-HAG 2000[ED]-2014.indd 5 25.4.2014 г. 10:31:48 ч.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Sparky HAG 2000ED Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info