Bedienungsanleitung Spartherm Linear Tunnel (Seite 10 von 27) (Englisch)

695382

Zoom out

Zoom in

Vorherige Seite

1/27

Nächste Seite

GB 10

After adding firewood, the combustion air must once again be opened fully

in order to burn the additional wood rapidly. This causes high combustion

temperatures to be reached again almost immediately, the key to complete and

environment-friendly combustion.

Depending on the type and quantity of wood, remaining embers and chimney

draught, this reheating phase may take about 5 minutes, until the combustion

air, in a way similar to that described in Point 8, can be restricted.

End of the combustion process!

3.3 FIRING/ADDING WOOD

• Depending on weather condition, move the actuating lever more of less

into centre position or slightly above it (closing the supply of air). This

always depends on experience and on prevailing conditions on location.

• Do not open the doors forcefully or gases may enter your living room

through a suddenly produced negative pressure. At first, open the door

slowly and only a crack.

• Putting fresh firewood onto hot embers prevents the possible release of

smoke when the door is opened.

• Typical intervals for adding firewood are 30 to 60 minutes approx., which

ensures that the fireplace insert can be operated continuously.

• When adding fresh firewood, completely cover the hot embers.

• Depending on how much firewood you add, you may move the actuating

lever completely to the right for a few minutes until that fresh firewood is

burning brightly.

• After adding fresh firewood, never choke off the flow of combustion air.

Risk of explosion!

• Never repeatedly put more than the recommended amount of wood onto

the fire.

• This also applies whenever the fireplace system is not operational

• Never close the actuating lever completely during the burn-up process

(risk of explosion).

4. TECHNICAL INFORMATION

4.1 HEATING DURING THE TRANSITION PERIOD

The basic requirement for correct fireplace system function is the draught

produced by your chimney (pressure head). This is dependent on the outside

temperature and therefore, to a large extent, on the season. Higher ambient

temperatures during the shoulder seasons (spring and fall) can lead to weaker

draughts and consequently, poorer combustion or more smoke production.

What can you do to help prevent this?

• Empty the ash can and grate before lighting a fire. Place grate with

embossed engraving facing downwards.

• If the chimney draught is less than this, a larger ‘initial burn’ should be

12. If no more firewood is to be added, the actu-

ating lever can be closed completely using the

‘cold hand’ as soon as there are only a few

remaining hot embers.

The end of the burning process is achieved when

the wood has burned completely, and no smold-

ering or incomplete combustion can occur. Now

the actuating lever can be closed (left position).

11. Provided that there are sufficient hot embers,

you can continue adding fresh firewood.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Spartherm Linear Tunnel Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Spartherm Linear Tunnel

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info