Bedienungsanleitung Spartherm Mini H2O (Seite 39 von 44) (Englisch)

810451

Zoom out

Zoom in

Vorherige Seite

1/44

Nächste Seite

GB 39

5.4 MAINTENANCE OF THE HEAT EXCHANGER

At regular intervals during the heating season, the water pressure of the

heating system must be checked. The H2O fireplace insert must only be

operated in a completely filled and ventilated state.

The technical heating inspection and checking of all safety devices (thermal

discharge safety device, safety valve, etc.) and of the other components,

such as the pump thermostat, is required yearly before the heating sea-

son. The instructions in the installation and operating manuals provided

by the respective manufacturers of the components must be complied

with. This check must only be executed by a specialised company that can

ensure the functionality of the individual components. We recommend that

you conclude a maintenance contract with your specialised company.

The yearly safety inspection (e.g. function check of the thermal

discharge safety device, pump thermostat, safety valve, expansion

vessel, etc.) should occur before the heating season. The executed yearly

safety inspections must be documented by your specialised company in

the commissioning protocol! If there is a complaint, documentation of the

maintenance tasks that have been executed must be submitted to service

personnel.

6. GUIDE

Note: The fireplace must not be used as a waste incinerator! Furthermore,

remember that the device is designed for temporary burning only. Continu-

ous burning cannot be achieved even through withdrawal of the combustion

air and is not permitted!

You can solve the following problems on your own:

Problem description Solution

Thermal discharge safety device

trips constantly (constant water

outflow through the discharge).

The water heat exchanger cannot

dissipate heat to the heating

system.

• The buffer tank is "full". Withdraw heat from the tank.

• Check function and settings of the pump thermostat and

the return flow boost.

• Set the pump one level higher (higher flow rate).

• Circulation pump does not run. Is the pump or power

connection defective?

• Return flow temperature too high, < 70°C

• Check whether the shut-off elements are closed

• Is sufficient heating water available?

Thermal discharge safety device

drips.

• Contamination of the discharge safety device.

• Flush the thermal discharge safety device by activating the

red button on the fitting.

• Check the seat of the connection seals and the piston

(see the manual provided by the manufacturer).

• If necessary, integrate filter in the system upstream of the

discharge safety device (pay attention to the minimum flow

rate!)

Gurgling noises, boiling noises in

the water-bearing parts of the H2O

fireplace insert. (Air in the system)

• Check system pressure.

• Ventilate system via the vent. For newly filled or topped

up systems it takes some time for all the air to exit. Often

ventilating once does not suffice.

Bypassklappe

Fig. 9

The steel front is not

shown in Fig. 9.

Bypass

damper

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Spartherm Mini H2O Seite 39

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Spartherm Mini H2O

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info