Bedienungsanleitung Spartherm Nova E H2O (Seite 5 von 28) (Englisch)

810449

Zoom out

Zoom in

Vorherige Seite

1/28

Nächste Seite

GB 5

1.2 TECHNICAL DATA

Nova E H2O

Max. admissible operating pressure 3,0 bar

Max. operating temperature1105 °C

Minimum return temperature 60 °C

Water-side resistance

at ~ 900 l/h

at ~ 1,000 l/h

at ~ 1,100 l/h

approx. 20

approx. 30

approx. 40

mbar

Minimum throughput - heating water* 700 l/h

Minimum throughput - thermal discharge safety device 900 l/h

Water content, approx. 42 Ltr.

Weight (empty, without accessories) 260 kg

Nominal power with heat recovery section 14,0 kW

Water-side power * 9,0 kW

Average flue gas temperature outflow top * 193 °C

Average flue gas temperature at side and rear ducts* 400 °C

Average flue gas temperature at the duct of the heat recovery section 166 °C

Necessary min. delivery pressure** 12 Pa

Mass flow of flue gas 12,7 g/s

Fill quantity (after test) 4,6 kg / 70 min.

Possible feed quantity 10 kg / 70 min.

Triplet values for 10 kg/70 min: 14 Pa

Average flue gas temperature outflow top * 230 °C

Average flue gas temperature on side and rear ducts* 520 °C

Average flue gas temperature on side and rear ducts* 25 g/s

Average flue gas temperature at the duct of the heat recovery section 280 °C

Between the triplet values after test (4.6 kg) and the max. fill quantity of 10 kg, interpolation is possible.

The draught length must be determined by the stove fitter based on the conditions, materials and

design. An estimate can be made using 50-80 K/m draught length. This means that 520°C - 200°C =

320 K / 60 K = 5 m

The thermal discharge safety device integrated in the heating system will

open the cold water inlet at a boiler temperature of approx. 95°C!

* The specified values represent the mean value over a combustion. These

values occur under test conditions, if in 70 min a quantity of approx. 4.6

kg of dry pieces of beech wood is burned with heat recovery section (see

Fig. 1d) (see point 4.).

If the heating insert is not combined with a heat recovery section or com-

parable component as in Fig. 1d, different capacities and capacity distribu-

tions occur.

** Increased delivery pressures must be reduced to less than 25 Pa through

suitable measures, such as a draught regulator or a damper.

Necessary minimum insulation thicknesses (Isorath 1000)

Attachment wall (side / rear) mm 80

Ceiling mm 80

Setup floor mm 0

Cladding in the case of a wall that must be protected mm 60

Necessary minimum distances to heating chamber / components

Convection chamber (side / rear) mm 60

To the setup floor mm 90

Heat recovery section to the wall of the heating chamber mm 100

Connecting line to the heating chamber ceiling mm 120

Minimum distances in the radiation areas of the view pane

Flammable parts mm 1000

Flammable parts behind a radiation protection element mm 400

Area of the non-flammable floor covering to the front mm 500

Area of the non-flammable floor covering to the side mm 300

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Spartherm Nova E H2O Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Spartherm Nova E H2O

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info