Bedienungsanleitung Spartherm Passo (Seite 18 von 53) (Englisch)

744243

Zoom out

Zoom in

Vorherige Seite

1/53

Nächste Seite

GB 18

2.3.4 CUT-OFF DEVICE

Exhaust systems must be created in accordance with the Technical Rules

of Tiled Stoves and Hot Air Heating System Trade (TROL). Stoves should

have a shut-off device in the exhaust gas flue. These devices must not be

self-closing and must not be positioned such as to prevent or hinder the

inspection and cleaning of connecting pipework. The position of the shut-off

device must be visible from the outside, e.g., from the position of the oper-

ating handle. Shut-off devices may only be installed in the exhaust manifold

or collecting pipe, the flue gas pipe stub or the pipeline connecting piece.

2.3.5 CONNECTING PIECE

Your stove is connected to the chimney with Ø 150 mm/Ø 160 mm connecting

pieces made of steel plate which is at least 2 mm thick. These connect-

ing pieces must satisfy the requirements specified in DIN 1298 and DIN EN

1856-2, and must be connected to the chimney system in accordance with

the requirements specified in DIN 18160 or the country-specific regulations.

It must be ensured that the flue gas pipe is installed in the shortest pos-

sible route upwards towards the chimney. To achieve this, ensure that the

flow of flue gas is redirected as few times as possible. Ensure that the flue

pipe is stable; where appropriate, the flue pipe may need to be secured with

brackets. If the flue leads through a combustible wall or is located close to

any combustible components, the flue is to be insulated according to the

respective regulations. The connecting line must always be mounted in such

a manner that it is possible to clean the connecting line at any time.This must

be ensured through a sufficient number of cleaning openings. If the stove is

rotatably mounted, the connecting pipe must be installed so that no negative

effects occur on the fixing. The flue pipe must not also turn. The minimum dis-

tance from the chimney connecting piece to any combustible components can

increase the distance from the stove to combustible components, in accord-

ance with the manufacturer specifications for the flue pipe. The specified

minimum distances to combustible components as stated in these instructions

refer to the fireplace and must be adjusted if necessary („2.3.3 Fire safety“

on page 14).

Ensure that a cleaning opening is located above the flue pipe connection with

gas evacuation to the top.

2.3.6 INSTALLING THE HEAT STORAGE STONES ON

TOP

The heat storage stones delivered with your stove are packed separately

due to their heavy weight. After the stove has been assigned its location in

the installation space, you can begin with the installation of separate heat

storage stones.

Insert the heat storage stones from the outside to the inside. When the stove

is connected with flue gas connection at the back, the heat storage stone

must be placed in the centre. If you connect the stove at the top, the central

heat stone is not required.

To insert the heat storage stones, remove the cover and the plate to control

the supply of heat. Then insert the heat storage stones as shown.

A = remove

B = insert

C = fit

Passo M:

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Spartherm Passo Seite 18

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Spartherm Passo

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info