Bedienungsanleitung Spartherm Piko L (Seite 8 von 53) (Englisch)

744253

Zoom out

Zoom in

Vorherige Seite

1/53

Nächste Seite

GB 8

Make sure that the sealing elements are correctly positioned under the

dummy cover and the flue gas outlet and ensure a tight seal. After screwing

in tight, fit the optional storage elements and convected air gate to prevent

airflow in reverse order and fit the lining elements (Fig. 8).

Note: The installation steps may be different depending on each stove model.

Special notes on the Piko H20 model

The Piko H20 model has gas evacuation to the side and to the top in addition

to the option of connecting the connecting piping around a corner. If the

installation situation of the Piko H2O stove has been decided already during

the planning phase, it is possible to order the stove with preassembled

matching flue gas outlet from the factory.

If the orientation of the flue gas outlet on site has to be changed, please

proceed as follows:

Installation from the top to the back/side

The flue gas outlet can be connected to the back in three different positions:

Carefully remove the top plate (A) (Fig. 9) of the stove and place it in a

protected place. When removing the top plate, ensure that the fitted dummy

cover (B) (Fig. 10) does not fall and get damaged.

Fig. 1

Fig. 5

Fig. 2

Fig. 6

Fig. 3

Fig. 7

Fig. 4

Fig. 8

2.3.1 CHANGING THE FLUE GAS CONNECTION

DIRECTION

The stove is prepared for the flue gas connection at the top when delivered.

Depending on the model, the flue gas connection position can be changed

so that it is aligned to the back, to the side or around corners. Follow these

installation steps when changing the flue gas connection position:

Changing the flue gas connection direction from to the top to the

back using the example of the Senso S

Installation from the top to the back

Remove the top plate (A) (Fig. 1) of the stove carefully and place it in a

protected place. When removing the top plate, ensure that the fitted dummy

cover (B) (Fig. 1) does not fall and gets damaged. Depending on the model,

the top plate of the stove must be removed either upwards in advance or

unlocked by parallel displacement to the front (model Stovo).

In stoves with fitted heat storage stones (for example, Cubo / Piko M (Fig.

2)) or convected air regulation (Fig. 3), these components must be removed

(„2.3.6 Installing the heat storage stones on top“ on page 18).

After removing the top plate, the flue gas connection piece (C) (Fig. 4)

bolted onto the stove body is visible. Remove these by loosening the internal

hexagonal bolts (SW 13). Now remove the dummy cover (D) (Fig. 5) on the

back of the covering panel for feed-through of the flue gas pipe. Depending

on the model, the perforation for this must be broken through or 2 fixing

screws loosened.

The only visible dummy cover (E) (Fig. 6) must be unscrewed using the

internal screws (SW13) and replaced with the previously removed flue gas

outlet (C) (Fig. 4). Fit the removed dummy cover (PE) onto the upper flue gas

outlet in order to close this (Fig. 7) (screw connection SW13).

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Spartherm Piko L Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Spartherm Piko L

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info