Bedienungsanleitung Spartherm Piko L (Seite 14 von 53) (Englisch)

744253

Zoom out

Zoom in

Vorherige Seite

1/53

Nächste Seite

GB 14

2.3.3 FIRE SAFETY

The handover inspection of your stove before commissioning is performed

by the chimney sweep responsible. You can also advise the chimney sweep

prior to installation about installation conditions on site, and can provide

advice on how to install your stove properly.

General Information on fire prevention

Stoves are heat generators and are subject to regulations and necessary

measures for fire protection. The fire regulations and the recommended

minimum clearances of the device must be observed even when selecting

the installation site. Basically, a minimum wall clearance of 5 cm to

the back wall must be adhered to. For reasons of safety and fire

protection, larger clearances must be ensured to protected walls or

combustible materials.

In the following table on page 17, the permissible clearances are docu-

mented according to the type of the stove and the type of on-site mounting

wall. Using the diagrams (Fig. 19-23), match the mounting situation, taking

into account the specified distances that need to be complied with.

Follow the instructions for fire protection during installation and

ask your local chimney sweeper.

• Mounting walls that are non-combustible or not to be protected are

suitable to withstand permanent exposure to temperatures > 85°C thanks

to their structure and their material type.

• Mounting walls that are combustible or to be protected (e.g. timber frame

construction) must be protected from temperatures > 85°C.

Before installing the stove, it is necessary to evaluate the mounting walls. If

the type of mounting wall cannot be clearly assigned, a specialist (chimney

sweep) must be consulted.

• Wallpaper as wall coverings in accordance with DIN 4102-1 are

non-combustible components and do not require special precautions

for fire protection. Ensure here that the underlying structure of the wall-

paper (e.g. timber frame construction) is very easily ignited or must be

protected and appropriate precautions must be taken!

• Ensure that the specified minimum clearances to the back and side wall

must be adjusted for the rotary devices.

• Ensure that the minimum clearances from chimney connecting piece to

combustible components are adhered to (see „2.3.5 Connecting piece“

on page 18).

• Combustible objects must not be located at a distance of 50 cm above

the fireplace!

Floor coverings near the stove

Floors in front of the combustion chamber opening have to be protected

from combustible materials by a board made of non-combustible materials.

The board must extend over at least 50 cm to the front and at least 30 cm

to the side (Fig. 19-23 C + D) (measured from the combustion chamber

opening or viewing window)!

No combustible components, furniture, curtains or decorations may be

placed in the area of direct radiant heat of the fire door or inspection glass.

This distance may be reduced to 400 mm if radiation protection plates are

installed between the fireplace and combustible structures on both sides.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Spartherm Piko L Seite 14

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Spartherm Piko L

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info