Bedienungsanleitung Spartherm Piko M (Seite 30 von 53) (Englisch)

744252

Zoom out

Zoom in

Vorherige Seite

1/53

Nächste Seite

GB 30

protocol“ on page 52). When first putting your appliance into service, only

start a moderate fire. This enables you to avoid cracks in the combustion

chamber covering (which may still contain residual humidity before the first

firing). Slowly increase the heating power to about 30% above nominal heat

output by setting the fire 3 to 5 times to give the corrosion coating applied

to the surfaces time to 'burn in' properly The paint can be slightly soft

during this process, please do not place any objects on the stove and do

not touch your device. During this burning-in process, an unpleasant odor

(sometimes accompanied by the build-up of smoke) may appear. Ensure the

provision of good room ventilation for this burn-in process. Open all doors

and windows to the outside of the building.

Initial commissioning of Senso M H2O / Piko H2O

The initial commissioning must only be executed after all necessary com-

ponents are connected and all necessary safety devices are integrated

and functional, the water heat exchanger is filled and the system has been

ventilated. Operation without water, when only partially filled or when safety

devices are not functioning is not permitted! During initial commissioning

of the water heat exchanger, it may be necessary to vent this several times.

Moreover, the owner must be instructed in detail concerning the operation,

function and maintenance of the overall system, including all supplemental

components. In addition, the measures for maintaining safe operation of the

system must be communicated to the owner. The executed instruction must

be documented in the commissioning protocol (see „10. Commissioning

protocol“ on page 52.). The installation and operating instructions must

always be kept in the vicinity of the Senso M H2O / Piko H2O where they can

be easily accessed.

Contaminated condensate exiting the combustion chamber liner may con-

taminate/damage the base unit. Here an absorbent pad should be placed

under the unit for the first burn-ups until condensate no longer emerges.

Before commissioning, check to ensure there are no objects in the combus-

tion chamber/in the ash drawer. These must be removed.

During heating and cooling, metallic grinding noises may be heard as the

components of your stove expand or contract. These are completely normal

and arise as a result of material expansion caused by the high temperatures.

4.1.1 COMBUSTION AIR REGULATION

Combustion air is regulated across an infinitely variable range using the

actuating lever located under the door. Adjustment takes place with the fire

door closed!

Air supply opened (A): For heating-up or for adding more firewood, move

the actuating lever fully to the right. The combustion chamber will now be

supplied with the maximum amount of air for primary and for secondary

combustion purposes.

Throttled combustion (B): leave the setting lever in a near-central position.

The primary combustion air supply is now closed, ensuring that the fire is

not supplied with too much air. Secondary air is diverted across the ceramic

viewing glass to prevent it from sooting up. This is the default position while

a fire is burning. The precise position

depends on local conditions and can be

adjusted by the operator to reflect the

combustion characteristics of the stove.

Air flow closed (C): actuating lever at

far left. The combustion chamber of the

stove receives no combustion air in this

setting. However, do not shut down the

air supply altogether until the fuel has

burned away completely. If the fireplace

is not in operation, you should always

close the air supply.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Spartherm Piko M Seite 30

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Spartherm Piko M

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info