Bedienungsanleitung Spartherm Piko (Seite 42 von 53) (Englisch)

744250

Zoom out

Zoom in

Vorherige Seite

1/53

Nächste Seite

GB 42

7. TROUBLESHOOTING

Problem Cause, explanation Chapter

note Solution

Glass becomes

sooted heavily,

rapidly and une-

venly.

You did not use the correct combusti-

on materials. 5. Use natural, bulky bits of timber compliant with 1st BImSchV §3 (German legislation).

The ambient temperature is above

about 15°C. The weather conditions

are unfavorable (e.g. fog). These wea-

ther conditions occur most frequently

in spring and fall.

4.5 Fill the fireplace with a small amount of fuel and light it with the damper fully open (max. air flow).

There is a temperature inversion. That

means that the upper layers of the atmo-

sphere are warmer than the lower layers.

4.5 Fill the fireplace with a small amount of fuel and light it with the damper fully open (max. air flow).

The combustion air controller is not

fully opened. 4.1.1 Move the air actuating lever into its far right-hand position.

The external combustion air line is

not free. 2.2.2.2 Clean the combustion air line.

Combustion air is too heavily

restricted. This means that soot accu-

mulates quickly, within just half an

hour. (it is normal for the fireplace unit

to become progressively dirtier from

operation of the system. When driving,

a car window becomes dirty, too!)

-Check the position of the air lever and, if necessary, open up the combustion air flow rate fully to bring the

fireplace unit up to operating temperature.

The seating of a gasket is not perfect. -Check all seals, e.g. open the fire door and press the seal fully into the door profile.

The wood is not dry enough. 5. Measure the residual humidity in the wood used with a humidity detector. The recommended residual humidity

is 20% or less.

Not enough wood has been added. (an

insufficient amount of wood can result

in temperatures in the stove not being

high enough).

4.2.2 The proper amount of wood feed per hour for your tiled stove can be found in the technical data.

The chimney draught is too strong /

too weak. -Observe the situation. The draught characteristics can be affected by the prevailing weather pattern. If the

glass continues to soot up badly, inform your chimney sweep.

Fire is difficult to

ignite

You did not use the correct combusti-

on materials. 5. Use natural, bulky bits of timber compliant with 1st BImSchV §3 (German legislation).

The wood is not dry enough. 5. Measure the residual humidity in the wood used with a humidity detector. The recommended residual humidity

is 20% or less.

The wood too thick. 5.

Use small-sized timber to light the fire. For firewood, use only split wood that is not thicker than about 8 cm

at its thickest point. The optimum length of firewood is approximately 20 - 25 cm. In the case of prolonged

heating, do not add too much wood. Instead, it is better to add smaller quantities of wood.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Spartherm Piko Seite 42

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Spartherm Piko

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info