Bedienungsanleitung Spartherm Senso S (Seite 5 von 53) (Englisch)

744240

Zoom out

Zoom in

Vorherige Seite

1/53

Nächste Seite

GB 5

inform your stove fitter. Protect the visible elements of the stove from soil-

ing and damage during installation. Only permitted and sufficiently strong

transport aids may be used to transport the stove.

The following points must be noted to ensure safe and problem-free

transport:

• It should be shipped in an upright position or slightly tilted on its back!

• Sack trucks used as a transport aid may only carry the stove from the

back.

2. ASSEMBLY INSTRUCTIONS

The assembly and installation of your stove must be carried out by a spe-

cialist. Please consult your district master chimney sweep before assem-

bling and installing the stove to clarify the suitability of the chimney system

and the installation site, and also when having any further questions.

2.1 BASIC INSTALLATION REQUIREMENTS

For installation, connection and operation of the stove, all relevant national

and European standards, as well as local regulations (DIN, DIN EN, state

construction ordinances, firing ordinances, etc.) must be complied with and

applied! The list of regulations given below is not exhaustive.

In the UK all stoves must be fitted in accordance with UK local building and

HETAS regulations. Appliances may only be commissioned by HETAS accred-

ited installers. Only appliances registered with DEFRA may be installed in UK

smoke controlled area.

FeuVo: Feuerungsverordnung (Firing Installation Ordinance) of the respec-

tive German Federal State

LBO: Regional building regulations and fire regulations of

VKF: VKF (Switzerland)

LRV: (Switzerland)

1. BlmschV: Erste Verordnung zur Durchführung des Bundes-Immis-

sionsschutzgesetz (First Ordinance on the Implementation of the Federal

Emissions Control Act)

TROL: Technical Rules of Tiled Stoves and

Hot Air Heating System Trade (ZVSHK)

DIN 1298 / EN 1856: Connecting flue pipes for heat generating systems

DIN EN 13240: Roomheaters fired by solid fuel

DIN 18896: Fireplaces fired by solid fuel Technical rules:

for installation and operation

DIN EN 13384 Chimneys: Thermal and fluid dynamic calculation methods

DIN 18160-1/2: Chimneys/house chimneys

DIN 4751 / DIN EN 12828: Heating systems in buildings –

Design for water-based heating systems

VDI 2035: Water treatment for heating systems

Art. 15a: B-VG (Austria)

Fireplaces may only be installed in rooms and places where the location,

construction situation and type of utilisation do not lead to hazards. The

floor area of the installation must be of a design and size so that the fire-

place can be operated properly and as intended.

2.1.1 INSTALLATION SITE

Your stove must not be installed:

1. In stairways, unless they are in residential buildings with two or fewer

flats.

2. In hallways with general access.

3. In garages.

4. In Fireplace systems in rooms or flats that are ventilated through venti-

lation systems or warm air heating through the use of fans, unless the

safe operation of the stove is ensured.

5. In rooms in which highly combustible or potentially explosive substances

or mixtures are processed, stored or manufactured in quantities that

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Spartherm Senso S Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Spartherm Senso S

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info