Bedienungsanleitung Spartherm Swing Insert (Seite 7 von 27) (Englisch)

810290

Zoom out

Zoom in

Vorherige Seite

1/27

Nächste Seite

GB 7

• The enclosed heat-resistant glove is only intended to provide protection

from the heat when using the operating handle, the ‘cold hand’ and the

damper lever. The glove is not fire-proof.

• Combustion air, depending on the type of fireplace insert, is either regu-

lated by means of the ‘cold hand’ (see chapter „3.2 Heating and firing“) or

without tools, using the telescopically extending operating handle.

• Read the operating instructions thoroughly to learn details about fuels and

other relevant topics (see chapter „2.1 Wood“).

• Initial start-up (commissioning) should be performed in consultation with

the fireplace installer who constructed the fireplace unit, or (better) with

his on-site assistance. All cladding parts must be completely dried to pre-

vent cracks or damage.

• If you have no external combustion air inlet, ensure you have a sufficient

supply of air to the installation space to prevent any negative pressure from

occurring in that space, and to ensure that no flue gases enter the space.

CAUTION! On controlled ventilation systems, bathroom ventilation systems

and fume extractor fans without a recirculating mode, there is also a risk

of negative pressure (vacuum)!!!

• Note contents of chapter „3.2 Heating and firing“.

Example for an air regulation lever used without tools with a Premium insert

Example on Varia ASh-4S-2 with telescopically extending air adjustment lever (damper)

Wood feed quantity based on the example

of the Varia 1V-51-4S

Nominal heat output 11.0 kW

Wood feed quantity 3.3 - 4.3 kg/h (± 30%)

We always recommend that you

burn split firewood in your fire-

place insert. Triangular-section

firewood made of beech with a

radius of 10 cm and a length of

33 cm weighs about 2.0 kg. The

circumferential edge dimension should be approx. 30 cm. The wood feed

quantity can vary by ± 30%.

Note: on larger fireplace inserts with a combustion chamber width of approx.

60 cm, the firewood can also be about 50 cm in length.

If the quantity added is exceeded consistently by more than 30 %, this can

damage the fireplace insert or the chimney. If the quantity of wood drops too

far below the recommended level, low combustion room temperature can lead

to poor burn-up and to sooting up of the window. Please do not drop more than

30% below the recommended quantity of wood. After setting up the fireplace

insert, only light a moderate fire initially. This enables you to avoid cracks in

the combustion chamber covering (which may still contain residual humidity

before the first firing). The amount burned should be increased gradually over

3 to 5 firings to about 30% above nominal heating capacity.

3. BURNING

3.1 INITIAL START-UP

• Check to ensure that all of the documents and accessories enclosed with

the fireplace insert are removed from the combustion chamber.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Spartherm Swing Insert Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Spartherm Swing Insert

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info