Certain Epic, Era, Camber, Rumor, Stumpjumper FSR and Enduro models are equipped with AUTOSAG, a unique new feature designed to simplify
and speed up the adjustment of air pressure. The AUTOSAG feature automatically determines the correct amount of sag, and eliminates the need to
refer to an air chart to determine the correct pressure based on rider weight. However, the shock still requires compression and rebound adjustment
based on type of terrain and rider weight. Please refer to the compression and rebound charts (page 17) following the setup steps.
NOTE: Shock air pressure can also be set up manually to rider preference.
Step 1: Setting Autosag
1. Position the shock compression lever or knob (blue) to the full open or off position . Remove the positive
air valve cap (black) and the AUTOSAG valve cap (red).
2. Attach a high-pressure shock pump to the positive air valve
• All models except Epic and Era: inflate to the rider’s weight in pounds (lb) plus 50psi. For kilograms,
multiply by three (e.g. 75kg = 225psi).
• Epic and Era: inflate to the rider’s weight in pounds (lb) plus 100psi. For kilograms, multiply by two +
100psi (e.g. 75kg = 250psi).
NOTE: Do not exceed 350psi before activating the Autosag valve (this is a starting pressure only). After the Autosag is
activated, Fox recommends a maximum working pressure of 300psi when riding.
3. Make sure the rider is wearing all gear that would normally be worn on a ride (shoes, helmet, hydration pack if
used, etc.). Mount the bicycle, prop up against a wall, and sit in the saddle in a normal riding position. Do not
set sag while riding.
4. Press the AUTOSAG valve . Air will release as the suspension settles into its pre-adjusted sag point.
Make sure all the air is out and release the valve.
5. Cycle the shock a few times , then dismount the bicycle.
6. Do not depress the AUTOSAG valve again, otherwise the proper sag setting will be lost, and will require this
procedure to be repeated from step #2.
7. Put the positive air and AUTOSAG valve caps back on.
NOTE: Rider weight in pounds (lb) plus the PSI (depending on model as described above) is the lowest amount of pressure that should be in the shock before
activating AUTOSAG. If the air pressure is too low, the AUTOSAG button may let air out of the negative chamber, which would result in incorrect sag.
NOTE: Sag is measured as the distance between the o-ring and the shock body’s seal, after the rider’s weight has been applied to the bike, with no
bounce. When AUTOSAG is correctly set, sag should measure approximately (20-30% of stroke, depending on riding/terrain experience, i.e travel).
If the rider is approaching 300lbs, AUTOSAG may not function, and sag may exceed the bike’s prescribed amount.
Step 2: Adjusting rebound
Refer to the rebound/compression chart to set the rebound damping (red knob). Rebound damping controls the rate at which the shock returns after it
has been compressed.
Clockwise for slower rebound (slow speed, bigger hits).
Counter-clockwise for faster rebound (higher speeds, small bumps, more traction).
Step 3: Adjusting compression
Refer to the chart to set the compression damping (blue knob).
SPECIALIZED / FOX BRAIN FADE: Controls the inertia valve damping. The blue knob adjusts damping (Race Tune or Trail Tune) from firm
(clockwise) to soft (counter-clockwise) and does NOT completely lock out the shock.
Backing off from full firm can help with tracking in loose terrain conditions while riding off camber sections or climbing. The soft setting can also help
during lengthy downhill or rugged conditions where the rider may want the suspension active at all times.
FOX CTD:Provides varying levels of compression damping, depending on whether the rider is climbing, trail riding or descending.
C (Climb): The firmest low-speed compression setting is activated for maximum pedaling efficiency.
T (Trail): Moderate low-speed compression setting is activated for an optimal blend of pedaling efficiency and bike control on variable terrain.
Factory Series shocks offer three levels of Trail adjust. Performance and Evolution shocks are preset with low-speed compression damping.
D (Descend): Low-speed compression setting optimized for the perfect balance of control and plushness for steep, aggressive descents.
SETUP DATA
DATE
RIDER WEIGHT
FORK PSI
FORK REBOUND DAMPING (# of clicks from full slow)
FORK COMPRESSION DAMPING (# of clicks from full firm)
SHOCK PSI
SHOCK REBOUND DAMPING (# of clicks from full slow)
SHOCK COMPRESSION DAMPING (# of clicks from full firm)
Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.
Art des Missbrauchs:
Forenregeln
Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:
Lesen Sie zuerst die Anleitung;
Schauen Sie nach, ob die Frage bereits gestellt wurde;
Stellen Sie die Frage so deutlich wie nur einigermaßen möglich;
Erwähnen Sie was Sie bereits versucht haben um das Problem zu lösen;
Ist Ihr Problem von einem Besucher gelöst dann lassen Sie ihn / sie wissen in diesem Forum;
Falls Sie reagieren möchten, so verwenden Sie bitte das Antworten- Formular;
Da ihre Frage für alle Besucher sichtbar ist, sollten Sie lieber keine persönliche Daten erwähnen.
Neu registrieren
Registrieren auf E - Mails für Specialized FSR - 2015 wenn:
neue Frage gestellt werden
neue Handbücher vorhanden sind
Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.
Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.
Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.
Ihre Frage wurde zu diesem Forum hinzugefügt
Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.
