Bedienungsanleitung Spektrum DX18 - SPM18000 (Seite 26 von 42) (Englisch)

726853

Zoom out

Zoom in

Vorherige Seite

1/42

Nächste Seite

26 SPEKTRUM DX18 • TRANSMITTER INSTRUCTION MANUAL

Sequencer

The Sequencer menu option provides this-then-that mixing with

a time delay. Five different sequences (S1 through S5) are avail-

able to control 2 functions each (A and B), in 2 timing directions

(forward or reverse). Sequences appear throughout function

screens as assignable switches.

CAUTION: Always review the action of a sequence on

the Monitor or X-Plus Monitor screen BEFORE operating

the model to ensure controls act as desired. Failure to do so

could cause a crash, resulting in property damage and or injury.

You can program multiple functions to sequentially activate

in response to an assigned switch. For example, an assigned

Gear switch can open gear doors, lower the gear, then close the

doors. In reverse, gear doors open, the gear retracts and the

gear doors close.

You can assign each Sequencer function to a switch in most

Function screens such as Flight Mode, Dual Rate, Mixing,

Throttle Curve, Pitch Curve, etc.

You can assign several functions to a sequence to decrease

the number of controls you need to touch during complex ﬂ ight

transitions, for example, applying your assigned dual rates and

exponential when the landing gear deploys and the ﬂ ight mode

changes.

If you select an S-Number-A sequence, for example, S3A, the

sequence operates as a timed 5-position switch. An S-Number-

B sequence operates as a timed 3-position switch. The 5

positions correspond to the sequencer values shown on the

time delay graph in the second Sequencer screen. In a function

screen, highlight each point (0-4) and select the switch position

desired for a function to be active.

When S1B (or another sequence-number-B) is selected as

a switch in a function, the sequence will operate as a timed

3-position switch. The 3 positions act as ‘kick points’ of the

movement at ﬁ xed percentages (equal thirds) of the sequencer

output. In a function screen, highlight each point (0-2) and select

the switch position desired for a function to be active.

Sequencer Set Up

1. In the ﬁ rst Sequencer screen, select 1 of the 5 available

sequences.

2. In the second Sequencer screen, assign a switch to the

sequence. We recommend using a 2-position switch.

Tip: If you need to use a 3-position switch, you must assign

one direction to two adjacent switch positions, for example,

0 and 1. Assign the opposite direction to the third switch

position.

3. Assign the timing for the Forward and Reverse directions as

desired. There is no delay when you use the Nor option. You

may also select a delay time between 0 and 30 seconds.

4. Assign names for each sequencer function, as desired.

5. Select either Step (S) or Proportional (P) for the Sequencer

output.Step: The sequence only changes at kick points.

Otherwise, there is a delay in the sequence until it reaches

the next kick point.

Proportional: The sequence movement is proportional

between kick points. The sequence maintains rate and

direction until it reaches the next kick point.

6. Adjust the Sequencer motion percentages in the third screen.

For example, you may move points 1, 2 and 3 closer to the

beginning of the sequence so the motion occurs earlier. This

results in a delay between point 3 and point 4 at the end of the

sequence.

Testing the Sequence

The Sequencer function determines the response for channels

included in the sequence.

Refer to the Monitor screen to see how respective channels

interact in the Sequencer.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Spektrum DX18 - SPM18000 Seite 26

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Spektrum DX18 - SPM18000

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info