680544
15
Zoom out
Zoom in
Vorherige Seite
1/24
Nächste Seite
10
DIFETTI CAUSE RIMEDI
Mandata insufficiente
La pompa non aspira
La pompa non parte
- la valvola di aspirazione non è
nell’acqua
- corpo pompa senza acqua
- aria nel tubo di aspirazione
- valvola di aspirazione che perde
- valvola di aspirazione ostruita
- è stata oltrepassata la profondità
di aspirazione max.
- non arriva corrente
- girante bloccata,intervento
protezione termica
Interruttore termico blocca la pompa
- controllare che ci sia la tensione
adeguata nella rete elettrica
- smontare e pulire la pompa
- sbloccare la pompa
- collocare la valvola di aspirazione
in acqua
- riempire d’acqua il tubo in
aspirazione
- controllare la tenuta del tubo
di aspirazione
- pulire la valvola di fondo
- controllare la profondità
d’ aspirazione
- smontare e pulire la pompa,
evitare l’aspirazione di materiale
estraneo. Aspettare fino a quando
il termico si ripristina (circa 20 min.)
- motore sovraccarico a causa di
troppa frizione
- controllare la profondità
d’aspirazione
- pulire la valvola di fondi
- collocare la valvola di fondo
più in profondità
- pulire la girante e sostituire
le parti usurate
- profondità d’aspirazione troppo
elevata
- valvola di fondo ostruita
- il livello dell’acqua si abbassa
velocemente
- capacità della pompa ridotta a
causa di materiali estranei
FAULTS CAUSES REMEDIES
Insufficient delivery
Pump does not suck
Pump does not start
- intake valve not in water
- no water in pump body
- air in suction pipe
- intake valve leaks
- intake valve clogged
- max.suction depth exceeded
- lack of electrical current
- rotor blocked , thermal
protection tripped
Thermal switch stops the pumps
- make sure the mains voltage is
suitable
- disassemble and clean the pump
- unclamp the pump
- pump intake valve in water
- fill suction pipe with water
- check suction pipe seal
- clean valve thoroughly
- clean suction basket
- check suction depth
- disassemble and clean pump take
measures to prevent suction of
foreign material. Wait until the
thermal switch reacts ( approx.20 min.)
- motor overload caused by
excessive friction
- check suction depth
- clean valve thoroughly
- situate foot valve deeper
- clean rotor and replace worn-out parts
- too high suction depth
- foot valve obstructed
- water level goes down rapidly
- reduced pump capacity due
to foreign bodies
15

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Speroni CM wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info